You are the very first person to explain step-by-step
@jordanday18133 жыл бұрын
This is the video I needed. Most videos I've watched the person just says "Press the bearing in" without any specification of "use a press bearing that ONLY fits the outer race" as well as "use a press bearing that ONLY fits the inner race" that is precisely what I needed to know. Thank you.
@Ed-de3ro8 ай бұрын
Hi, Spencer's Garage, I just came across your video in search of doing my own wheel bearing replacement myself. Your video is one of the best out there I have seen. You explained everything in detail step by step. Thank you for taking the time to post and share your video. Great job.
@spencersgarage8 ай бұрын
Thank you!
@CampervanAdventures3 ай бұрын
Stumbled across this video,I’m currently getting my old Nissan pulsar gtir back up and running after sitting in my old garage for 17 years,moved house so now got room and time to work on the old gal…..your video came in very handy many many thanks😉👍
@johnnyjimj Жыл бұрын
After seeing the difficulties you experienced while trying to remove the outer race I think I'll just put the hub back on and get a shop to do the job. My civic is "only" 20 years old but it lived all its life in the Salt Belt. It was already unbelievably difficult to remove the lower ball joint and I only realized it should have a dust shield after watching a few videos, because it's so rusted you can't even see where it used to be.
@stevensimpson687222 күн бұрын
Excellent video. I screwed this up too many times in the past.
@ahsenabbasi49682 жыл бұрын
@15:20 I ran into the same problem. I grabbed a hammer and an adapter that fit the inner race and just went for it until it was just the outer race stuck in the knuckle. There’s a lip sticks out in the middle of the bearing and I got the right sized adapter for that and kept hammering. Pb blaster helps too and once it starts sinking, add more adapters on top until you’re close. After that, I used the tool as intended to get the rest of it out and I was able to get the whole thing out of the knuckle.
@TheJakePoole3 жыл бұрын
I don't know why, but 19:30 - 19:42 cracked me up. Haha. I'm doing all my front ball joints and wheel bearings, and this video helped a lot. I'm very thankful that my outer races both came out with everything else. I was terrified of dealing with that. Haha. Thanks!
@J.E.Taylor2 жыл бұрын
Those pliers would have been super handy when I did the front bearings on our 13 Escape. I used a combo of screwdrivers and small pry bar to work it around and out. Installing it I used one of the adapters in the bearing tool rental kit. Those pliers were so fast!
@ParallaxVisuals2 жыл бұрын
Thank you for this clip! I wish i’d seen it before leaving my car only with 3 wheels in the garage….. thanks for the complete clip with all the messups!
@williamthomas15492 жыл бұрын
Thanks for the video. I am glad for your guidance on mistakes. I make them all the time. You saved me from making the same ones!
@__Dja2 жыл бұрын
Timken is definitely the best when it comes to replacing Honda wheel bearings
@dagorodriguez52657 ай бұрын
Do you know the part #? Or where to buy this for 1999 civic
@brianamaya18098 ай бұрын
Super detailed with every step so helpful thank you i would be attempting this soon
@udedmario2 жыл бұрын
Great video, easy to follow and done with easily obtainable tools!
@CivicFiberglassDoor Жыл бұрын
Agreed. Ive done 10+ Civic bearing jobs with this tool with no problem. I think an important factor is that I used clean high-pressure wheel bearing grease on the main screw threads, as well as between any surface that turns with friction, such as the screw and the face of the cups or washers.
@Maplecook Жыл бұрын
Awesome stuff, Spencer. Subbed!
@johnnyamador3712 жыл бұрын
appreciate ya, ft.worth,TX
@joseperez-zo6fr15 күн бұрын
My kits different but your video is awesome
@nixmix3544 Жыл бұрын
Wow amazing Video! You’re very talented and well explained video. 🙏👏🏻 Thank You!
@djaric Жыл бұрын
Glad I decided my wheel bearings were fine on my 97 civic. 😅 I already have enough work to do.. Also this car has clearly never seen snow or salt. mustbenice
@joaobarbosa63922 жыл бұрын
Great video, great explanation, keep going brother like that helping a lot people out there 👍 😀 👏 😄
@rodolfojimenez39892 жыл бұрын
thank you good buddy you explain it perfectly!
@jamesclifford28303 жыл бұрын
I coincidentally have that same hub waiting to be put on lol
@craigconway409329 күн бұрын
Very good explanation
@josebetancourt65552 жыл бұрын
This video helped me a lot brother. Definitely subscribing 💪🙏
@spencersgarage2 жыл бұрын
Thanks for the sub!
@mitchsiripanya38702 ай бұрын
Well explanatory, Thank you
@mlez7197 Жыл бұрын
Thank you SR..😮 😃 great explanation
@RanjitSingh-h8b16 күн бұрын
Good work 👍
@k20castro2 жыл бұрын
Nice snap ring pliers. I have some harbor freight ones they worked alright
@khimsophacarfixing2 жыл бұрын
Thanks for your sharing knowledge!
@dabrokeleague11 күн бұрын
What size socket did you use for both sides other the kit?
@paulmacal80372 жыл бұрын
Ahhhhhhhhhhh finally man thank you
@CurrentGenGamesWithNick2 жыл бұрын
I don't know how you did this man but job well done I bought it and I could not get my bearing in it would just not go in I gave it to Mavis the thing kept Titan it just kept loosening
@currenbeuchat4318 Жыл бұрын
I ran into the same problem today where the outer race was the only thing left inside of the knuckle… now I’m screwed. Gonna need some help from your dad now lol
@kumingo2 жыл бұрын
I had same issue w the same wheel bearing puller with the outer race of the bearing.
@rayone233 жыл бұрын
This video helped me out a lot thank you
@spencersgarage3 жыл бұрын
Glad to help!
@jw85602 жыл бұрын
Great video! Well done!!
@WranglertdКүн бұрын
good details
@johnnguyen2376 Жыл бұрын
Very well explained.Thank you .
@abanimishra32465 ай бұрын
Good job sir❤❤
@moe23983 жыл бұрын
Thx man... you helped me out a lot with this!!!!
@mahdavimail7 ай бұрын
So the only way to take out the outer race is jack hammer?! Tnx for video
@Seraphim4017 ай бұрын
Nice job bro.
@spencersgarage7 ай бұрын
Thanks 👍🏼
@michaelpiecewicz97483 жыл бұрын
Thinking that you don’t live in the rust belt!!!! So lucky are you
@rayclaudio414111 ай бұрын
You're amazing
@abdoualilahthomas80312 жыл бұрын
Great job, but you should have changed the lower balljoint with a honda one ( after market doesent take too long like for me 3 months and started making noise) also since it will be the same work taking the knuckle out the car.
@spencersgarage2 жыл бұрын
I actually refreshed the entire suspension two years ago with Honda OEM and Hardrace parts.
@dannysautorepair3 жыл бұрын
Great video
@veesixtyfiverider64793 жыл бұрын
Good video. Good to see the mistakes as well. As for removing the bearing, do you think using the impact wrench contributed to the bearing getting destroyed on its way out? Had you continued to use hand tools, do you think you would've "felt" something off? Thanks!
@juggernaut64983 жыл бұрын
In my experience using power tools wouldn't have made a difference it just makes the job easier
@narseh1232 жыл бұрын
There is no way he could have removed the outer race using the tools at hand.
@JAI456242 жыл бұрын
THANK YOU
@BoostedPastime2 жыл бұрын
Thank you!
@mistacdawg68822 жыл бұрын
My putter race is stuck and both inner races came out with the hub, what tool can I use to get the putter race out?
@spencersgarage2 жыл бұрын
I ran into that difficulty as well. I explain how I removed the outer race in the video.
@thenet95373 жыл бұрын
What size is the bolt
@irisbaez19722 жыл бұрын
Is it dangerous to re-use the front old hub? People recommend using a new one. Mine is free rust and 154 K miles only.
@MegaHomieJ2 жыл бұрын
you may have found your answer already, but in case others are wondering the same question, reusing the hubs is completely safe as long as you are able to remove the wheel bearing without scoring the hub. you do not want to reuse wheel bearings if the hub is removed once before, this could lead to premature failure.
@rafaelo84983 жыл бұрын
The cover protect the brake padsand disk from dirt
@JohnnieIsBored2 жыл бұрын
I just pressed my bearing and now the inner bearing wobbles. Do you know if this is normal or not?
@spencersgarage2 жыл бұрын
Yes. The inner race may have about 1-2mm of movement. Excessive movement will mean the bearing is damaged though.
@JohnnieIsBored2 жыл бұрын
@@spencersgarage does it matter which way bearing is facing? I have a non abs if that helps and only one side has the black facing.
@mg87188 ай бұрын
You coulda used a cold steel chisel and hammer to get the rest of that stuck race out.
@lowkd54652 жыл бұрын
What happend to the shields lol
@David-fy3bi Жыл бұрын
Not channel locks but snap ring pliers
@michaelpersson68 Жыл бұрын
Amazon it was $64 us i think buy for Ford Transit connect 2011
@joeybuddy962 жыл бұрын
2:40 Ah, the outside inner race.
@steeezzyy801 Жыл бұрын
20:56 bruh i pushed the hub using the spindle, no wonder it fucked up the bearing immediately 😭😭😭
@justinlangston87872 жыл бұрын
4:32 Giggity
@CurrentGenGamesWithNick2 жыл бұрын
put in freezer it easy ?
@dangda-ww7de2 жыл бұрын
sure you did, you left off the dusk shield.
@severocortez8082 Жыл бұрын
Te falto poner la lámina
@naumsantana46705 ай бұрын
Cara muito maneiro!! Mas.. não entendi nada . Kkkkkk
@randyrobison3352 жыл бұрын
You never mentioned packing the bearings with grease in your video.
@spencersgarage2 жыл бұрын
They are closed bearings. No need.
@JohnT20882 жыл бұрын
Most wheel bearing are closed sealed so no need to pack grease into the bearings