Installing Maxpeedingrods Coilovers on Iamcraiggentry’s 1992 Acura Integra RS

If you'd like to get some merch and support the builds you see on the channel, check out my store at: www.etsy.com/s...
Linking up with @Iamcraiggentry to get his DA Integra off the stock suspension and lowered with some coilovers.
Visit Craig's channel: / iamcraiggentry
TruHart Rear Camber Kit - amzn.to/32qngy0
TruHard Rear Toe Kit - amzn.to/3dt8JYv
Lower Control Arms - amzn.to/3v1c8ne
Centric Front Brake Rotors - amzn.to/3v1a6Ud
Centric Rear Brake Rotors - amzn.to/3es4dJh
Instagram: @crxseth / ​
Amazon: www.amazon.com...

[@T12i99iN]

My favorite gen for Integra's. Over all early 90s Honda and Acura were my first Honda love..lol

[@anthonymoore1464]

Been scared to tackle suspension on my 92 DA9. glad to find some good info.

[@nunzioformica3763]

Very nice done

[@bobagosto6441]

My Best Friends Dad bought her a 1992 LS in 1992 -Captiva Blue Pearl made the car look REALLY sweet It was fast.... It was an Auto

[@ejjuan3008]

Ooofff that crx and the integra 🔥🔥

[@alexcalderon808]

Finaly some integra da tuning. Ive owned two da's with as many jdm parts i could get back in the day.

[@djweszone]

MORE MORE on the INTEGRA lets see some wheels tires and full exhuast .

[@crxseth]

Craig sold this car a couple years ago.

[@ATR-_]

I also have a 92 DA 5 Spd but it is LSVtec frankensteined by the previous owner and it's pretty shoddy but I picked it up for 3k, I'll probably end up doing a channel on it because it's now developed a mold problem on top of a myriad of jank from the last guy.

[@fk8bebop]

quick tip would be to make sure to adjust the preload to your liking before you put the coilovers on folks. it’s easy to get excited and throw them on and worry only about the ride height but preload is very important!

[@crxseth]

Thanks for the tip

[@devinalmeida7023]

What did u set your preload at cause i got a pair an need to do so badly

[@samfoote9630]

A trick i learned with those rotor retaining screws if you don't have an impact philips, is to use the round end of a ball peen hammer centered and use another hammer to indent it and it comes right out, you don't have to use to retain the new, the wheel holds it on. If you do though tighten down then use the point on the Phillips and hit with hammer right on the edge of the screw to lock it in.

[@albono780]

Looks real good man . Just a tip for when installing adjustable toe and camber links . Make sure you have the same amount of thread on the inner and outer link . Don’t just adjust one side they both need to be equal

[@crxseth]

Thanks for the tip.

[@jasonvincent690]

So clean

[@ernestoencinas343]

Man that looks good I need to get moving on my crx

[@SOY741310]

What kind of hatch/trunk struts are those? 😮 it’d be cool to hit my keyless trunk button and have it pop open when I go buy groceries lol

[@cbdreamer1709]

Probably could have done the inner tie rod too. Plus you will need to compress caliper piston to fit the brake pads

[@bryoma]

that feeling when you jack the car down after lowering it! 🥵🥵🥵🥵 cant wait till next Cars and Coffee!

[@crxseth]

Can't wait!

[@cheeseburguhgaming9581]

I have a question on jacking up the front of the DA integra where was the jacking point? Because I was trying to find mines and I can't seem to put it together or find my jack point

[@gohardorgohome7687]

It came out really good what a clean integra 👍👍👍

[@mystr_e]

Should’ve greased up the caliper pins.

[@jerrys.t.9368]

I know this is old but I have a question on the rear LCAs. Were the shockbushing lining up with the stock ones? My LCAs were a little off. The shock bushing seems closer to the end bushing on the truharts.

[@crxseth]

I’m not entirely sure. Make sure they are for your car. Many of these Hondas are similar with minor differences.

[@goseth2865]

Hi seth I’m interested in Honda’s aswell if that makes sense! Lol

[@lowandslowda9]

can i have the link to the coils?

[@ISellDough]

I noticed that you did Not Install anything for your Front-End Camber. Since this video, did you ever go back and do so? If so, what did you use?

[@crxseth]

This was on my friend’s car, but I’m not sure if he has added front camber adjustment yet. His KZbin channel is IAmCraigGentry in case he has put an update about it.

[@ISellDough]

@@crxseth I have a 1990 Integra I’d like to lower; Am looking for some advice on how to address the Front-End camber... I’ve seen the different options available (upper arm, spc ball joint, swivel bolts). My biggest concern is the upper arms clearance, after installing One of these, in the wheel well. Have you worked on any 1990-93 integra’s?

[@gqfilipino95]

Time for a new exhaust.

[@crxseth]

He has one on order, but it’s back-ordered until July!

[@gqfilipino95]

@@crxseth love the video. I had a 93 teal integra gsr. Miss that car.

[@MidnightRamenGuy]

Have you ever had issues installing the rear coil overs on stock rear mounts??? I did mine on a VW golf mk7 and the maxpeedingrods threads was to big???

[@crxseth]

I've only done it on Hondas, so I don't have any experience with that issue.

[@EdgarGarcia-ow2mf]

Where's the link to the channel for acura integra?

[@crxseth]

In the video description.

[@ur_asian_milfoil]

For sale?

[@crxseth]

Craig just picked this car up a few weeks ago, so I doubt it.

[@victorwilks88]

Great video ...always looking forward to the content Like share and subscribe 👆