The gauge in this video is NOT an X series gauge. My gauge is a classic gauge. I believe that is for the new version of the AEM requires the Brown wire to be wired in as well. I have heard it goes to Pin D21 but I cannot confirm 100% as I have not tested. [30-4110] Classic gauge only has: Red - 12V Power Black - Ground White - 0-5v Output Blue - Serial Output [30-0300] The X series has: Red - 12V Power Black - Ground Green/Black - AEMnet- /CANL White/Black - AEMnet+ / CANH Blue - Serial / RS-232 Output White - 0-5v Output Positive Brown - 0-5v Output Negative Hope this helps!!
@JamesEhler11 ай бұрын
I like that. "We are not professionals. We do what we can, with what we have, to make our projects work." Amen. Same here, but i never heard it put better than that.
@CJBuilt11 ай бұрын
Hell yeah!🙌🏼🙌🏼😂
@Flex_Gordan2 жыл бұрын
Finally someone that knows how to show and explain how it’s done thanks again bro literally did it in 30 min thanks to you
@CJBuilt2 жыл бұрын
Happy to help 🙌🏽🔥
@waltervreeland9147 Жыл бұрын
saved my life. just got my first z6 build and all it needs to run is a afr and boost gauge. thanks to you i’ll get it done tomorrow !!
@CJBuilt Жыл бұрын
Awesome to hear!! Hope this helped out🙌🏼🙌🏼 Good luck with the Z6! Hella setup
@waltervreeland9147 Жыл бұрын
@@CJBuiltshe runs after today! thanks again bro!!!
@CJBuilt Жыл бұрын
@@waltervreeland9147 Love to see it! Very glad this could help!
@nicholas19494 ай бұрын
took me forever to find out if I could replace the factory o2 with my wideband. Thanks for the help
@carlosbertoldi56038 ай бұрын
thx working good on my old p28 95 si
@andysghettogarage28312 жыл бұрын
god tier video thank you
@CJBuilt2 жыл бұрын
I appreciate the support brotha!! Glad it helped out 🙌🏽🙌🏽
@p72crxhf439 ай бұрын
Nice videos brother but i heard you have to wire the brown wire to d21?
@CJBuilt8 ай бұрын
My version does not have the brown wire, I believe that is for the new version of the AEM. I have not worked with them before but it does seem that it does need to have the brown routed as well. Mine only had: Red Black White Blue
@brittanymorris61834 ай бұрын
@@CJBuiltwhere did the blue go
@CarsonDelaney-wy2qh8 ай бұрын
Do you have to connect the brown wire on the gauge to d21??
@CJBuilt8 ай бұрын
My version does not have the brown wire, I believe that is for the new version of the AEM. I have not worked with them before but it does seem that it does need to have the brown routed as well. Mine only had: Red Black White Blue
@Dokkado2 жыл бұрын
Nayz bro.. no bullshit, straight to the point, precise instructions, video and editing on point. Deserves a "subscribe'. 😉 Been having trouble getting proper info on wideband sensors. Thanks for the vid.
@CJBuilt2 жыл бұрын
Glad it can help! I appreciate the sub and the positive feedback!
@PipoRacing7172 жыл бұрын
Gracias por el contenido saludo 🔥💪🏽🇵🇷🙏🏼❤️
@CJBuilt2 жыл бұрын
Muchas gracias!!🙌🏽🙌🏽
@santiagogarcia5878 ай бұрын
hi, can i conect the sensor without de gauge?
@CJBuilt8 ай бұрын
You may be able to do it without the gauge but I know AEM has the output directly from the gauge. You may be able to solder it in but I do not know the workflow to do so.
@alexanderlara2315 Жыл бұрын
Hello! I have a p28 for my 00’ d16y8 with an OBD2B jumper harness. Does the pin out differ from OBD2A?
@CJBuilt Жыл бұрын
Hi! That is the same harness I used for my setup as well since mine is a 2000. It might vary slightly but for sure it won’t affect you since you’re OBD2B👍🏻 Just make sure you are wiring in the correct signal wire and you should be good
@alexanderlara2315 Жыл бұрын
@@CJBuilt Cool! And we count from the ECU side correct?
@CJBuilt Жыл бұрын
Yes. Verify of course using the diagram but it’s the plug while it’s facing the ecu
@brittanymorris61834 ай бұрын
Where does the blue wire go?
@CJBuilt4 ай бұрын
Not needed for this type of install. The white one is the only one required. The blue wire is for Serial Output. The white wire is for 0-5v signal. Any questions lmk!
@SwaybarspresentsPeasantl-pi4cg6 ай бұрын
you CUT the freaking wire cody LMAO!! great vid tho helped me with all the confusion
@CJBuilt6 ай бұрын
LMAOOOOO Glad I can be of help!
@mcorley187 Жыл бұрын
What setting did you have the gauge on? P0 like it comes or did you switch it to p04?
@CJBuilt Жыл бұрын
P0 still, have not touched the settings.
@mcorley187 Жыл бұрын
Yeah my s300 was upset because originally I selected the p04 setting. I couldn’t for the life of me figure out how to show 0-5v on s300. Well that was the problem. When I switched to the p0 setting it corrected that.
@CJBuilt Жыл бұрын
Good to know! Thanks for the feedback! Is yours an X series or the older style?
@ianagawa97952 жыл бұрын
Bro, aside from the AEM wideband, is the PLX or MTX-L PLUS also applicable?
@CJBuilt2 жыл бұрын
I believe it is, I do not see why not. Only difference I would see is the output wire may be a different color on the other gauges
@higgsbuilt59142 жыл бұрын
Thank you bro🙏🏿 really thank you
@CJBuilt2 жыл бұрын
Anytime! Glad this video can help 🙌🏽🙌🏽🙌🏽
@carloscuevas164 Жыл бұрын
Was this the aem x series ?
@CJBuilt Жыл бұрын
Hi! No this was not an X series. Check the manual for the wire on the X series for output. It may be different than mine
@bolly09152 жыл бұрын
What program are you using?
@CJBuilt2 жыл бұрын
Honda tuning suite
@dusankovacevic1117 ай бұрын
Where wire 4 going from 02senzor
@CJBuilt6 ай бұрын
Which wire are you speaking of? Let me know which gauge you have and what color wire 🙌🏼