Subscribe to CJ Pony Parts so you never miss out on our giveaways and the latest options for your Focus ST: kzbin.info Purchase this part here: www.cjponyparts.com/eibach-coil-spring-pro-kit-set-focus-st-07-08-2013-2018/p/35144140/?.com& Or if your ST is an early 2013: www.cjponyparts.com/eibach-coil-spring-pro-kit-set-focus-st-early-2013/p/35140140/?.com&
@EUCitizenFedUpWithAllThisCrap5 ай бұрын
How can you recommend something that rubs and never sits correct neither on stock shock nor on Bilstein B6 or B8, this is the worst set of springs ever.
@mibrown99322 жыл бұрын
Just recently installed these springs on my st. These springs are amazing. I’ve heard on forums these were available as a option in the UK and it makes sense. They easily pass for stock springs. Ride is amazing. It may be slightly stiffer than stock but nothing extreme. I’ve lowered cars before and the ride was rough. This feels stock with virtually no body roll and wheel gap is all but gone.
@alexgiron57562 жыл бұрын
Did you keep the stock shocks and struts when installing? I have a 2014 Focus SE and it's impossible to find aftermarket shocks and struts that don't end up costing me as much as coilovers would, total. Thanks
@nickgsxgaming6 жыл бұрын
Keep the st videos coming big help 👍🏻👍🏻👍🏻
@trickstervas10206 жыл бұрын
Yes the st videos are back!
@Dar3D453 жыл бұрын
Im literally now going to do your trick for seperating the strut from the knuckle from now on. Too many times have a pulled the entire knuckle with the strut attached to seperate out of the vehicle
@obee-one6 жыл бұрын
Great watch like always. 10/10 still trying to find me one.
@g.p.v._s.p.o.t54163 жыл бұрын
I have a ford focus St 2017 and installed the springs godspeed 1.2 and strut monroe, but not under anything seems the original suspension. The only thing that did not change were the bump stops, I'm use the oem, you should change them for a shorter one.
@dham994 жыл бұрын
You guys always make the best how-to vids, appreciate the content you put up! But man..seeing all that surface rust is painful..at least toss some rustoleum on there ^_^
@cjponyparts4 жыл бұрын
Thank you and good point! This car belongs to a customer and has been his year round daily driver since new. It could use some love for sure.
@StormLaker3 жыл бұрын
Great time for new struts too
@johnlefever32203 жыл бұрын
what lowering springs are the most recomended the most of any on the market, theres too mant to choose from
@TrailVapor2 жыл бұрын
the lower spring end: has an end stop but also a dip 'marker' where the previous spring end lined up with (1cm away from the metal stop). Which is the correct location for the spring end?
@shy82913 жыл бұрын
does this install still work if I own a post facelift 2016? I read most of the comments but I just want to be sure the tools he mentioned are the same ones post facelift. I need to order some online before I do the install
@Mk4DeSouza6 жыл бұрын
What kind of rims are those? Awesome video tho
@jbailey11876 жыл бұрын
Wedssport SA-10R in 18x8.5
@codybaker32845 жыл бұрын
What kind of rim and tire setup is that I need to get that for mine and the offset???
@highseaspaul79056 жыл бұрын
I have 13 st would ❤️ to do the Bilstein coil over setup that’s on your site .Would like to see a video on that setup with driving reviews
@MacLaw30845 жыл бұрын
can anyone answer this question? if im having trouble removing the top end link bolt (my version requires offset box wrench and hex key), can I just remove the bottom endlink bolt instead? endlink should just come out still attached to the strut, if im not mistaken.
@tommylong21514 жыл бұрын
Angel Lawless Ik it’s been 6 months, but did you figure this out, bc I was trying to do mine today and couldn’t get it and gave up
@Steven115254 жыл бұрын
Theres
@Steven115254 жыл бұрын
@@tommylong2151 theres a space between the endlink and the strut where you can put a wrench to hold the stud while you loosen the nut. Or you can use the hex hole in front to.hold the stud while you loosen the nut
@tommylong21514 жыл бұрын
Steven11525 That’s only on the prefacelift, luckily my friend had the right tool, you need a pass through wrench sadly :(
@Steven115254 жыл бұрын
@@tommylong2151 huh. I have both on my 17 ST2
@rinXneko9 ай бұрын
What wheels?
@Medicbobs4 жыл бұрын
How the fuck you got that upper tie rod bolt off so easy blows my mind
@jesusolguin2074 жыл бұрын
What spring compressor is that ?
@txcavi4 жыл бұрын
Took me 8 hours to do this job, with a lift and with a mechanic. 3 hours my butt
@cptnscoob3 жыл бұрын
Im going to try to tackle this 100% on jack stands
@ZeldaxLegacy3 жыл бұрын
@@cptnscoob how did it go? I'm about to do mine in about 30 minutes on jack stands as well.
@GEYSER945 жыл бұрын
I HAVE A FOCUS ST WITH SPACERS IN THE REAR WHEELS OF 25MM, I WANT TO PUT THESE SPRINGS, MY DOUBT IS: ARE THEY GOING TO STICK OR ROZE MY RIMS WITH THE BODY?
@dobrinia933 жыл бұрын
Did you do it???
@TVwazhere6 жыл бұрын
So wait, are you telling me the bump stock provided goes on the Shock, and not on the bottom of the Spring Perch like you showed in the original Sportline install five years ago?...... Shit kzbin.info/www/bejne/gWLYf2SniN9ljpYm20s
@EUCitizenFedUpWithAllThisCrap5 ай бұрын
These are terrible! Do not buy, the 2nd ring bunches up and pushes out to the side and causes insane rubbing, if you match them with Bilstein B8's it's even worse. What a waste of 2 years of my life not being able to properly use the car, even lost control in a corner on the track. DO NOT BUY THESE. I'm testing alternatives at the moment, I think part 113502308FA will work for the front and I'm also testing 118400607VA.
@rustybrown7715 ай бұрын
Yes I just failed inspection saying these are rubbing. I took one side off it is def a slight rub. I’ve tried just about everything I can’t get them in without them touching the body of the car. Not happy right now.
@EUCitizenFedUpWithAllThisCrap4 ай бұрын
@@rustybrown771 it’s horrible, worst product ever. I can confirm the other springs work, but the handling is horrible. Get white line or H&R
@TrancerGTR6 жыл бұрын
You leave old rusty shock absorbers, no way...not in your US style...:))
@wickedgames87684 жыл бұрын
Could have sand down the rust and paint . I love Chris fix it he would
@joshuaschmidt55525 жыл бұрын
You should show the whole process not just the perfect shots
@metasploited57904 жыл бұрын
Most people don't need their hand held for an hour and a half. A 12 minute video is much more realistic.
@BOMEFSY5 жыл бұрын
FUCK this install..lol I'm a complete novice and let me say yea....took awhile.
@QuB35 жыл бұрын
Damn that car is rusty. Does the owner live by the sea?
@cjponyparts5 жыл бұрын
Daily driver, pa winters, salted roads
@AutoSteps5 жыл бұрын
@@cjponyparts if i wanted to skip the rear shock removal, are the bump stops the same from stock to the eibach?