Tap to unmute

Clutch Adjustment Part III

  Рет қаралды 177,130

clloyd234

clloyd234

Күн бұрын

Пікірлер: 22
@gusraynor
@gusraynor 10 жыл бұрын
Great video. Truly appreciate the time you spent making the video.
@cwj9202
@cwj9202 8 жыл бұрын
Mr. Lloyd, I would suggest that you inform the viewers that once the factory sets the clutch linkage geometry, the only adjustment necessary after that to obtain the recommended clutch pedal free play is to adjust the clutch near the release bearing. I have seen mechanics attempt to set the clutch brake with linkage adjustments -- bad news. Excellent video series.
@rileybennis4029
@rileybennis4029 7 жыл бұрын
Chad Jessup not true after the 1/2 inch adjustment is made you adjust the gap in between the throw out bearing and the fork to 1/8 inch you achieve this by adjusting linkage. You then check to assure that the free play is 1 1/2 to 2 inches!
@moparmike2003
@moparmike2003 12 жыл бұрын
great group of videos, thank you
@MrUbiquitousTech
@MrUbiquitousTech 8 жыл бұрын
Great series, thank you for sharing!
@mtnfordman
@mtnfordman 12 жыл бұрын
Very informative,thanks for sharing with us your knowledge on this subject.
@johnniehall9033
@johnniehall9033 9 жыл бұрын
I had a new clutch installed last week. I work in the oil fields and getting to a shop isn't easy. my new clutch is working it's way to the floorboard. I am adjusting it back out using the clutch quick adjust. why is it un-adjusting ?
@dmj6151
@dmj6151 10 жыл бұрын
I have to hold the clutch pedal pressed down for several serconds in order to engage in gear, in this case i need to turn the bolt clockwise, how many half turns? Thanx you
@Jason-ju7df
@Jason-ju7df 9 жыл бұрын
I adjusted my International Prostar Eaton Clutch/Eaton 10speed and the clutch brake does not engage. Freeplay correct, tried 2", 1", 1/2" still not engaging. Please advise.
@Eliasdagoatt
@Eliasdagoatt 10 жыл бұрын
Great job !!!!
@alexcataraga1205
@alexcataraga1205 9 жыл бұрын
Newbie question. What is than cable hanging from clutch brake? Thanks.
@gaetatravaglio3344
@gaetatravaglio3344 9 жыл бұрын
+Alex Cataraga that is an extension hose so you can grease the through out bearing , without having to reach way up there , on older trucks that becomes quite messy , so again that greases the bearing , and half way up the transmission bell housing there is a fitting on both side's to grease the cross shaft , often missed ! Frank
@cheeptorque
@cheeptorque 17 жыл бұрын
thnx a million clloyd.."S" (u gonna do uself outta a job if u not careful)..very informative..just wot us rookies need.."S"
@vindanarine3577
@vindanarine3577 10 жыл бұрын
Does this apply to 2014 mack granite as well
@RHILTONJR100
@RHILTONJR100 10 жыл бұрын
Yes it does apply for the Mack clutches as well. But much harder to access the adjuster. As you look up inside and see bearing and clutch brake you will see the clutch fork covering the gap. As the clutch is depressed to release for adjustment the fork will travel forward towards the adjuster. In some cases blocking your ratchet from accessing the adjuster. If this is the case a wrench can be used, although it can be a slow process. ( a word of CAUTION if your having someone in the cab depressing the clutch for you. THE CLUTCH FORK TRAVELING FORWARD CAN TAKE FINGERS OFF.) use the proper tools to keep hands and fingers clear and use good communication with the person helping you.The gap is 1/2" bet5ween brake and bearing. Work slowly. The clutch brake adjustment is totally different. As you will notice its a cable and not linkage. Set your clutch brake depth by threading or unthreading the clevis yolk attached to the clutch arm . You can also adjust the cable itself by releasing the jam nuts. These adjustments are all done from underneath. This can be very tricky to set the adjustment as the tolerances are very fine. Good luck, work safe!
@vindanarine3577
@vindanarine3577 10 жыл бұрын
I tried it , it worked , it was tricky indeed, great video it helped a lot
@cpuzzo
@cpuzzo 17 жыл бұрын
very good , more videos please!
@RHILTONJR100
@RHILTONJR100 10 жыл бұрын
Good vid, but your not including your cluding what gap to set your adjustment. Turn your adjuster until you have a 1/2" gap between your clutch brake and bearing. I found a 1/2" bolt as a good measuring device. Place the bolt on the threaded end in the gap. Turn the adjuster until the bolt fits between the gap. Now your "internal adjustment is set. Then move on to your "external or linkage adjustment" to set you clutch brake.
@saadalmwali8334
@saadalmwali8334 8 жыл бұрын
That's really helpful thanks
@israelpaladines9515
@israelpaladines9515 10 жыл бұрын
Thank youuu!!!!!
@bobbyhorn7059
@bobbyhorn7059 9 жыл бұрын
Man adj the clutch for wear does not have a thing to do with free travel you get 1/2 inch between the throw out bearing and clutch brake then you get your free travel from the top adj linkage.
@1970onkar
@1970onkar 14 жыл бұрын
good
Solo Clutch Style - Video 1
10:01
Snider Fleet Solutions Corporate Office
Рет қаралды 41 М.
Clutch Operation Explanation using a Clutch Cutaway Trainer
11:25
Transportation Heavy Equipment Tech
Рет қаралды 72 М.
Tuna 🍣 ​⁠@patrickzeinali ​⁠@ChefRush
00:48
albert_cancook
Рет қаралды 148 МЛН
To Brawl AND BEYOND!
00:51
Brawl Stars
Рет қаралды 17 МЛН
Chain Game Strong ⛓️
00:21
Anwar Jibawi
Рет қаралды 41 МЛН
Don’t Choose The Wrong Box 😱
00:41
Topper Guild
Рет қаралды 62 МЛН
Adjusting an Eaton advantage clutch
6:58
Jason The Municipal Mechanic
Рет қаралды 23 М.
How to adjust old style clutch on a big truck
6:04
Gordon Robertson DIY
Рет қаралды 550 М.
Clutch Adjustment on a semi truck (Eaton Fuller)
6:08
JROD
Рет қаралды 771 М.
Solo Clutch Style Adjusting Procedures - Video #2
5:02
Snider Fleet Solutions Corporate Office
Рет қаралды 54 М.
Eaton Solo Clutch Replacement
22:26
Skylar Hill Shop
Рет қаралды 18 М.
Tuna 🍣 ​⁠@patrickzeinali ​⁠@ChefRush
00:48
albert_cancook
Рет қаралды 148 МЛН