Planning to Buy or to Try the Clutch Max Kit on the Market? Watch This before you spend your money 💰🤑 #clutchmax#Stage4
Пікірлер: 43
@ApocalypticAwakening3 ай бұрын
450 hp Mazdaspeed 3 , clutchmax stage 3, and fidanza flywheel have been holding for the last 2 years
@TanzRacingАй бұрын
"Everything is holding up perfectly. You're so lucky!"
@tylorjames378 Жыл бұрын
I'd say launching at 7500 on a cheap ass clutch that you didn't even break in whatsoever did exactly what's to be expected lol
@TanzRacing Жыл бұрын
😂
@rockbrothers8546 Жыл бұрын
Exactly
@dgummo2728 Жыл бұрын
I've been running the same stage 4 clutch on my civic for the past 3 years. At one point was around 400hp trying to push the engine to its limits. After going on almost 4 years it's just now beginning to slip.
@TanzRacing Жыл бұрын
Your very lucky it last for that long. Mine was only about after n Installing it.ahaha
@rockbrothers8546 Жыл бұрын
You got to break it in you can’t just rip it up
@harryazzole78142 жыл бұрын
I got the Clutch Max stage 5 unsprung and while the clutch held all the power no issue it actually created an even worse problem where the diaphragm on the pressure plate was pushing too far in towards the crank and completely ate the thrust bearings on a low mileage motor. When I took the pressure plate off to compare to a stock one the diaphragm teeth were about 1/4 longer towards the center than stock.
@TanzRacing2 жыл бұрын
It did damage to you I can tell bro damn. Switch to some trusted Brands Bro. Hope this vids and comments feedback can help to other like us building our cars.
@civicpride1986 Жыл бұрын
An ebay stage 4 clutch did the same to one of my motors.. the thrust washers completely fell off after all the hard pressure on the crank and block... that ruin a good block and crank.. thanks to that cheap clutch... never again i will trust cheap clutches.
@surendransuppiah2 жыл бұрын
Thanks for your input. Was considering this brand for my turbocharged 1nzfe. I will go for mantic instead
@TanzRacing2 жыл бұрын
Welcome bro. Is that a new Brand as well Mantic. Let me know how's it holding.
@dongli1627 Жыл бұрын
i use same thing on my 350z, track only, two years, still fine
@thebestmena1789 Жыл бұрын
Que stage amigo ?
@TanzRacing Жыл бұрын
Stage 4
@cyberfuria Жыл бұрын
I purchased a stage 1 kit from clutch max replacing my 350z OEM kit and it didn’t engage the gears so I had to take it off. Seems like the pressure plate is the problem.
@TanzRacing Жыл бұрын
Coming from the different cars I think they should look for this issues.its not like our money fell off from the trees . 😞
@josephbishop64622 жыл бұрын
I'm not doubting that the clutches suck however all clutches and new flywheels have a break in period and if you're saying that you were launching that could definitely play into it failing.
@TanzRacing2 жыл бұрын
I consider your opinion bro. However, one of our ek hatches installed, and give it good miles and break in before testing on the dragstrip. the same issue it broke. sad to say. he warn me before I didn't listen. like you said clutch and flywheel need a break-in period. but I'm not using tthis clutch again. haha.
@josephbishop64622 жыл бұрын
@@TanzRacing just throw some JB weld on it and send it
@TanzRacing2 жыл бұрын
@@josephbishop6462 lmao full send
@jw50312 жыл бұрын
@@TanzRacing Everything I hear on the ClutchMax kits are that the pressure plates take a shit. Besides the damage to the friction from the pressure plate cracking, the rest of the clutch (disc) held up to the abuse?
@TanzRacing2 жыл бұрын
@@jw5031 some parts of it are gone.
@kgillerjg Жыл бұрын
Thanks for the video. I was about to buy one.
@TanzRacing Жыл бұрын
Welcome Brother.
@grytis Жыл бұрын
did you do a clutch brake in period (500miles)?
@TanzRacing Жыл бұрын
Can't even drive the car on the Roads. These cars here in Doha our not permitted only we run them on the Track. Once they saw this rust bucket on the street it's a bye bye 😅
@randalceniceros81572 жыл бұрын
Serious burns marks on the plate What are you doing ?
@TanzRacing2 жыл бұрын
I send it the Drag Strip. Did the the Burn out And Launch😅
@ekbenny39392 жыл бұрын
Their k series stage 2-3 holds fine
@Khalidsvt10110 ай бұрын
sorry but installation is junk and obviously no break in
@TanzRacingАй бұрын
I apologize for the inconvenience. I will make an effort to improve by purchasing the necessary tools.
@alltherpm2 жыл бұрын
Just a flywheel is 400 so whole clutch kit for under 300 with wheel what u want bro
@vsmcoupe2 жыл бұрын
music to loud
@bigmotor38452 жыл бұрын
Just installed a Clutch Max Clutch Sucks!!!!!!!!!!
@TanzRacing2 жыл бұрын
Hope your not ending the way I do bro
@pat85902 жыл бұрын
They Suck ASS!!! For Anyone wondering. DON'T BUT CLUTCH MAX!!! They burn out way too fast and just overall quality is Garbage 🗑. You would be better off buying a used clutch then to waste the $ on that shit
@pat85902 жыл бұрын
CLUTCH MAX = GARBAGE!!!!! Get any other brand! Or just save up for a Decent one!
@TanzRacing2 жыл бұрын
I did bro. got an exedy stage 2 clutch. 12.1 sec on the track .
@pat85902 жыл бұрын
@@TanzRacing Hell yeah. Exedy Clutches are the JAM!