It is not difficult for me to assemble a broken axle housing like a pen

Рет қаралды 124,651

CNC Master1

Күн бұрын

Пікірлер: 47

@tonteria24 10 ай бұрын

It's strange that the break is so square, it had probably already broken there before.

@antoniovalverdemoreno125 11 ай бұрын

Otro gra trabajo,que por cierto,un trabajo imposible de hacer en España,salud y buena suerte...🐧

@MushtaqAhmed-xs8jx 10 ай бұрын

Mashallah Good work amazing zabardast

@cmsracing 11 ай бұрын

No way they're getting %100 penetration without beveling the edges before welding.

@oldschool1993 11 ай бұрын

I want some of that Pakistani welding rod- gets penetration through mud, oil, grease, dirt and you never have to bevel your parts.

@hasanurrahman5964 11 ай бұрын

Not even 25%!

@DEREK-mq3ik 11 ай бұрын

And not cleaning the weld surface? All that grease and dirt in the weld?? SMH

@ThanhNguyen-kw2mz 11 ай бұрын

🙌🙌🙌🙌🤣🤣🤣🤣

@bobhudson6659 11 ай бұрын

Yes. They had the root clearance but what happened to the 60 degree V? Also how do you weld into iron oxide from the flame cut - plus no V? As others have mentioned maybe 25% penetration. Wonder how long the always overloaded truck lasted afterwards?

@gordonwelcher9598 10 ай бұрын

They have to overload the trucks to get the job, then drive a dangerous vehicle to make money. After that they have to spend the money they made for repairs. Not an ideal system.

@The_Black_Sheep95 11 ай бұрын

That differential been "repaired" many many times before

@pkfan5112 11 ай бұрын

Only one man wear shoes, others sandals, no gloves, no safety glass sorry for those people, they don’t have any protection at all

@jonfoster1566 10 ай бұрын

Meets or exceeds all 3rd world country safety and repair standards.

@plumbcrazy375 11 ай бұрын

I'm impressed with how much they get done with basic tools if they didn't overload the trucks wouldn't have catastrophic failures

@starybezpiek7880 11 ай бұрын

Ten most już kiedyś pękł i pęknie ponownie.

@tomaszkulik8761 10 ай бұрын

Przy takim przeładowaniu pęknie... Dziwię się, że nie fazują krawędzi przed spawaniem.

@秋山武彦-e1b 7 ай бұрын

No good welding because they did not make edge preparation at all. therefore cannot get good strength.

@LockeM140 11 ай бұрын

No prep before welding shocking work

@joelchabot5167 11 ай бұрын

Strange regular failure, scam?

@mikespain8655 11 ай бұрын

Install a rubber mat in back of vehicle to protect the bed.

@ipaddlemyowncanoe.7441 11 ай бұрын

It's amazing what you guys do with what you have. No big shop with all fancy tools. Use the basics to get the job done. Good stuff. 👍👍🇨🇦🙂

@AhaLava-z6y 10 ай бұрын

Молодцы ребята , у вас золотые руки и наплюйте на все санкции --вы все равно правы.

@tamduong2875 10 ай бұрын

Những người thợ khá tốt nếu vào hảng sẻ thay một cái mới rất tốn tiền

@raphaquan 11 ай бұрын

It must be a very common factory problem, due to the type of cut and they even have a lathe designed for that type of axle.

@agussoediro5415 11 ай бұрын

Bagus,Paman 👍👍👍👍

@AmusedBarnOwl-hc1zg 10 ай бұрын

Yeah safety first I always say

@chrisbanning413 11 ай бұрын

Wonder how they check the axle is aligned with the diff centre

@ВалериПарыгин 10 ай бұрын

Что за диск на болгарка не убиваемый индусы молодцы , Вася Я ишим

@samsudeenjainulabdeen912 11 ай бұрын

This kind of work never succeed. Not advisable. Foolish work.

@samsudeenjainulabdeen912 11 ай бұрын

No groove for welding root run penetration

@aadelaadel-s5k 11 ай бұрын

Cool work thanks 👍

@gothicblood2061 9 ай бұрын

so that's a broken axle no that looks like its been cut up to look like a broken axle and the back end of the axle been fix up be for , can see the cuts in the axle . on the bearing shaft where the bearing sits had it , there been no oil or Greece on or in axle for some time where the axle shaft gos in got lot of rust in the ends didn't clean the part where you groove for welding