How To Fix Brother LS-2125 Sewing Machine

[@neilskiw]

I appreciated seeing where screws are located, and experiencing your adventure. It will help to smooth the bumps in anyone else machine repair. May I suggest additional light in future productions...... Enjoy your day!

[@Turtletoots3]

That little plastic thing is a real B. Spent half an hour trying to undo it. This video was useful, thanks.

[@Lookatthebottom]

If mine wasn't working so well I would try to open it again to give a better explanation. If I remember correctly, make sure all the screw are out and grab the section on opposite sides with both hands while pulling the edges outward and try to separate the lip that latches in the center with a flat screwdriver.

[@Lookatthebottom]

03:45

[@Turtletoots3]

@@Lookatthebottom Wow, speedy reply. I edited my comment. I got it open but will have to sand down the plastic where I made a bit of a mess of it so it doesn't snag anything. There was another plastic latch in the curve but that one wasn't quite as stubborn.

[@samsamant3281]

Vey helpful, thank you! I was tryin to get my mom's machine open just to look at the state inside. The thing just wouldnt come apart even after taking off the screws. When you did this, i knew i did not have to take anything else off before pulling thw two halves apart!

[@amyc4083]

Thank you for this! Had to open it up to put the belt back on. This video was helpful!

[@Lookatthebottom]

Great to hear!

[@tracybooth8148]

Thank you so much! This has just help me out of a tight spot where my thread got stuck!

[@idalia_rdl]

BLESS YOU! This video just saved my life, thank you so much!!!

[@nickakawoodstock]

We were going to throw our machine out until we saw your video. Thanks for the help finding the clips!

[@v_lh109]

Thank you so much!! I couldn't figure out how to take the front cover off.

[@calypsowarrior9061]

Same

[@Lookatthebottom]

Glad I could help!

[@tanyamoore3215]

Same with my machine I took off all the screws but it doesn’t open, pls help

[@botasbarrios]

Thank you so much. Your video has helped me a lot. Greetings from Mexico.

[@ZingL6]

This is a good video but the television running in the background was terribly distracting!

[@kathy4451]

Thanks for this! Girl was gonna muscle it open...lol...oh a screw😮😂

[@hectorretamal3338]

Thanks! From Chile

[@belmontevito]

Very clean

[@blissprokop6239]

To keep track of screws and other small parts removed, I suggest keeping them in one of housing that were removed.. Either the light cover or the cover over the bobbin. Thank you for the video.

[@azucenavargas2861]

La parte donde se hasen ojales pequeños laperilla pequeñas está suelta como ajustarla orepararla

[@Atheist-Pinar]

Thank You🌷 I couldn't find 👓 the opening with light in it, Thanks to your video🧵 I learned a lot ..Greetings From Nederlands ✨

[@Lookatthebottom]

You are very welcome. The light is on the inside of the front cover.

[@mehrunnishalimbada3157]

I can't open 😫 mine

[@janetpayne7738]

Thank you so much. I have my sisters machine to repair and I found your video. It was real helpful, though Im not sure this is the same problem. I cannot turn the wheel as it will only go down so far. You mentioned cogs and stuff, I thought it may have been a problem with the belt. Your video was a slight dark for me to see clearly. I will certainly try the method that you have shown,. Do you have any more thoughts on what may be the problem.? Thank you.

[@Lookatthebottom]

I had a similar situation where the needle wouldn't go all the way down. There is a weighed mount for the needle I had to unscrew it and adjust the height manually. I may be able to assist more when you get to that point with the cover off.

[@maisygirl07]

wish you had better lighting but what a great video :)

[@anniedana3919]

Nice and easy demo thanks .

[@Lookatthebottom]

You're welcome!

[@BellA-uz1wh]

Mine suddenly stop the bobbin case 😢 when i opened, i found a screw and i dont know where should i put it back 😭

[@baosue7952]

SUPPER HELPFUL. THANKS!!!😀

[@Lookatthebottom]

Glad it helped!

[@rjj2316]

Great video- Thanks so much!!!

[@nabihakhanom9675]

hi my sewing machine stopped moving and if feels like it just doesnt work like there is no power at all and idk of i should replace the drive belt coz i havent rlly opened the sewing machine up yet

[@glennlopez6772]

Hi! Thanks but are you satisfied with the foot controller hesitating. Mine goes into high speed!

[@Lookatthebottom]

I just started using it, but the foot controller is a bit touchy, I just adjust my foot position and never fully engage the pedal. My daughter was able to sew much more smoothly than I.

[@Evonne-us9ev]

@glennlopez6773. Mine got loud humming sound, reluctant to start sewing , what could be the problem, all I think about it is I never clean it, never oil it, is it too now, cause after I bought the sewing oil, it still not improving at all!

[@cynthiasony]

Sir, my machine's feed dog is not able to move the fabric. How to fix it. Brother LS 2125

[@Lookatthebottom]

Did it just suddenly occur while sewing, or after retreading? Maybe check the bobbin and thread path. Are there any other issues with your machine right now?

[@carmenlaswisse6762]

Same here. It moves back and forth but not up and down. I just finished adjusting the bobbins track. To catch thread.

[@valentinadesiato5282]

hi, i removed the screws following your video but i can't detach the body like you did! could you tell me what the problem is?

[@Lookatthebottom]

There is an internal plastic latch, it takes some serious squeezing a pulling to release it.

[@valentinadesiato5282]

@@Lookatthebottom Thank you so much for your help, where are you at?

[@shahidmattoo6526]

Great job

[@inthehalflight9303]

Excellent, thank you!

[@ogrehaslayers605]

Thank you!

[@KarinaDoRego]

How do I do the adjustment now that the machine is apart??

[@Lookatthebottom]

There is more than one possible adjustment. It depends on the specific issue.

[@KarinaDoRego]

Well, the teeth line up with the gear on that bar.. my bobbin holder doesn't turn far enough for the hook to catch. I wish I could share photos.

[@KarinaDoRego]

I have even tried making the adjustment on the needle arm. Nothing is working. :(

[@Jen-dx4io]

Hi, any chance you might be able to do a tutorial on how to remove a needle bar assy or needle bar in general? Your the only one who just happens to have the same machine as me and I’m having trouble removing it

[@Lookatthebottom]

Great suggestion!

[@Lookatthebottom]

What I recall is that if you loosen the screw mounting the needle bar, it moves freely. You have to find the right level to allow the needle to catch the thread from the bobbin. It's a bit of trial and error, but there is a KZbin video or Google diagram that shows the general position. Hook timing.

[@reynartegamboa2211]

I dont know how to repair this sewing machine . Pls help me

[@Umeomar]

can you please help me to reinstall the brother tension knob plz

[@Lookatthebottom]

Did the shaft of the knob break? or did the knob loosen from the shaft?

[@Umeomar]

@@Lookatthebottom i opend the tension knob but now i can't fix it

[@Umeomar]

i jus bought please help me to reinstall it

[@judeea99]

What’s the size of the screwdriver you used? My sewing machine didn’t come with a screwdriver. Also, my sewing light gets really hot. Would you know how to fix this problem?

[@Lookatthebottom]

You will need a small phillips screwdriver. I didn't remove my light while making this repair like I should have, and I broke it in the process. Now I use an external light, I haven't missed it much, so I would remove it and leave it out if it's causing problems with the heat.

[@stephencox5753]

You can replace the incandescent bulb with an LED lamp - it will put out much less heat and more light. Put these keywords into the search bar of the retailer you want to use "led+sewing+machine+light+to+replace+incandescent+bulb+e12+base" make sure to pick one that is at least a 15 watt equivalent

[@carolchalker]

Sir, can I ask for assistances. I’ve left my sewing machine for number of years and trying to use it today and the rod that holds the needle is stuck. The threading for bobbin works well just the sewing needle is unable to move. By pedal or manual ..... can I know how this can be fixed? Many thanks 🙏

[@Lookatthebottom]

It sounds like you have the same issue that I had originally. The video should help you repair it yourself.

[@carolchalker]

High West Enterprises thank you 😊

[@snewcomer22]

The small screw goes on the front, to the right of the door. All the other screws are the same.

[@Lookatthebottom]

thank you

[@nabihakhanom9675]

does this sewing machine have a drive belt

[@Lookatthebottom]

nibz nibbles bo

[@nabihakhanom9675]

@@Lookatthebottom then how does it work

[@Lookatthebottom]

@@nabihakhanom9675 There is a sliding gear mechanism at the lower rear of the machine.

[@stephencox5753]

Search for Brother drive belt XA1196021

[@Shagotthejuicenow]

Hi I can’t seem to figure out why my thread keeps coming out the needle once I start a stitch. Pressor foot is down, about 5 inches of thread and bobbin thread hanging, I tried putting the needle down in the fabric to start and still nothing. Please help 😩😩😩

[@Lookatthebottom]

Try pulling out twice as much, its normal for that small length to pull through.

[@Shagotthejuicenow]

Thanks I’ll try that out

[@kendoall2205]

thanks

[@nadeeshani8120]

Hi I need an needle plate my machin same one and i cant fund it can you plz help me on this

[@Lookatthebottom]

Are you missing the needle plate screws as well?

[@jasmine-ruff-puff9951]

My machine made a huge snapping noise and I'm struggling with the cover lol. Thanks!

[@yolandacastillo7443]

Hello..My machine is no moving..The needle don't move.. up or down.. It's stock. Trying to move it down..Nothing. Stop sewing..or running..

[@Evonne-us9ev]

Same here, also hard to start machine to sew either use foot controller or hand wheel, the humming sound loud, what’s the problem? Please!

[@reynartegamboa2211]

My brother Ls 2125 sewing machine is not working,have no power .how to repair this machine .

[@Lookatthebottom]

@@reynartegamboa2211 make sure the power cable is pressed all the way in and check the foot pedal if it clicks when pressed. If it doesn’t work you may want to replace to avoid an electrical hazard

[@Lookatthebottom]

@@reynartegamboa2211 I purchased a second one from Walmart. Price was reduced and upgraded quality from the old one.

[@DrKhalidShakir]

Hi it’s beautiful

[@Lookatthebottom]

Hey, thanks

[@kaihatsuki3181]

Of course, there's screws. My dumb ass keeps trying to open it for an hour, never notice the screw. Thanks 😅

[@reynartegamboa2211]

May be the motor already have fault

[@Lookatthebottom]

The motor is probably the most durable part of this machine. If is making any type of sound it's more likely jammed, or the plastic gears have failed.

[@fortytwocrayons3485]

My front cover won’t budge 😂 Something is stuck at the top.

[@Lookatthebottom]

Be sure that all the screws are removed, it takes some finagling to release the interior latch, you have to pull and apply pressure, it almost felt like something was going to snap, then it just came apart. If my machine wasn't working so well and I wasn't busy, I would take it apart again to demonstrate, but if you work at it you will get it.

[@TheBlackburnTeam]

I wished you were closely. I have two brothers and both have problems

[@christinadawson2911]

too much background sounds

[@jacquelinefersovich7031]

Great video...except where you skipped on how to adjust the bobbin to be able to work properly. THAT is the part I NEEDED to see😔

[@Lookatthebottom]

What exactly is your bobbin doing that needs adjusting?

[@Lookatthebottom]

You have to adjust the needle bar up or down to catch the thread. There is a screw that should be loosened then you can adjust the bar up or down. The needle has to enter the bobbin case in sync. There is a video or diagram that I recall.

[@Lookatthebottom]

hook timing

[@shirleyschubring9602]

too dark

[@Lookatthebottom]

True I really wasn’t set up to do a video at the time but I didn’t ’t want to miss the opportunity to share this

[@brandonrowe5963]

turn off your TV next time..

[@user-sc8dn1kq6d]

... maybe he doesn’t want to☺️

[@thiccrudy]

do you know how i could fix the little button that you also had broken? i thought mine was okay but as i was taking it apart and cleaning everything i noticed the knob kind of just sits in place and spins freely because it was broken before hand (i found it at a goodwill)

[@Lookatthebottom]

that small knob to adjust the thread tension if you have the broken piece, I’ve had luck mending broken plastic with the super glue baking soda hack