Complete Valvetronic Repair Guide BMW N55 N20

DIY guide for rebuild/repair valvetronic system on this BMW F10 535xi with N55B30 engine. This information can be used on BMW N20 also. We going to replace:
*Valvetronic eccentric shaft
*Valvetronic eccentric shaft bearings
*Valvetronic unit, which is integrated with hall effect sensors + the electric motor for the system, in one whole unit
*Fuel injectors (this is not required everytime)
*New valve cover gasket + some critical bolts and other bits
In this video we going to show, how this procedure should be done step-by-step. Removing of the valvetronic springs will be included.
Fault codes:
2A38 Valvetronic sluggish or open circuit
2A37 Valvetronic, eccentric shaft sensor: plausibility
2A47 Valvetronic, eccentric shaft sensor: plausibility
2A45 Valvetronic, actuator motor: plausibility
2A77 Control unit, internal fault: Valvetronic output stage
2A37 Valvetronic, actuator motor: power supply
Additional info about Valvetronic system:
The Valvetronic system is a BMW variable valve lift system which, in combination with variable valve timing, allows infinite adjustment of the intake valve timing and duration. The system claims to improve fuel economy and emissions, and negates the need for a throttle body in regular use.
First introduced by BMW on the 316ti compact in 2001, Valvetronic has since been added to many of BMW's engines. The first application of this technology in a turbocharged engine was the N55 engine.
Support the channel : / crankauto
Shop coordinates ( for business inquiries ) : / crankauto
CRANK

[@johnboutsikos6049]

Excellent work ... the shaft was replaced to match the gear on the valvetronic motor s pae BMW servics technical service bulletin . As a retired BMW tech with 38 years congratulations really superb work

[@forrestychan]

Thanks for doing this DIY! Please do more!🤙🏻

[@tsskage]

Very good detailed info - thank you!

[@lorenpeterson657]

Thank you so much-great instructions and will make this job a lot easier for me!

[@jaredweinberger2305]

Excellent video, very detailed

[@BigBlockRalle]

excellent thank you for your experience

[@e55v86]

Excellent job👍

[@iskamakaunt]

Много добро видео. Браво

[@stuckinthemiddlewithyou9998]

Very nicely done job and video. Done properly, very organized with good camera angles. Nicely explained beginning to end. And everything you need to know beginning to end including dme relearn. So many bad videos out there. This is now my go-to video. Liked & sub'd

[@Nico_335i_DCT]

Nice detailed DIY guys. Thanks for sharing. On my 335i I change the oil and filter every 12.000 km. So in the middle of what the car recommends. Thanks for sharing, Dutch regards, Nico.

[@JBK-kv5nk]

It is such a great video and thorough explanation & guidance step by step. Questions: 1. Do I need to disconnect the battery(negative & positive) prior to pulling out the Valveteonic motor and eccentric shaft? 2. The Valvetronic was replaced by a local shop however they couldn't process valvetronic adaptation as error codes couldn't be deleted, 2D43 and 2D41. Not sure they even replaced it correctly. Will these codes be deleted automatically and will I be able to process adaptation if I replace both valvetronic motor and eccentric shaft? DME seems working fine as it functions other adjustment such as DSC adaptation and others. Your comments would be much appreciated.

[@crank3646]

It is always preferable to disconnect the battery when working on the internals on any engine. If everything is done correctly, you should be able to do adaptions as shown in the video. Doesn't matter if the fault codes are there are not, it is important that they are not "Present" or "Actual". If they are "History" codes no need to worry about it.

[@JBK-kv5nk]

You have cleared my questions that I've been looking for the last month and a half. Much appreciated your quick response. Thank you very much!!!!

[@SmileIso]

Nice job, you had to replace injectors, did you program them ? I heard that some values much be programmed in.

[@asid731]

I’m working on a 2013 535i. Sometimes I’ll get misfire codes on 1,2,3 and sometimes it will be on 4,5,6. It will start but I have to hold it at 3000rpm otherwise it will cut off. Also I’m getting an air mass code.

[@mohammadmo9554]

Bro did you figure it out? My car been doing that for a year now smh

[@JCod306]

Can you link that tool you used for the springs please?

[@chestertownelectric6290]

Why did you only inspect and rebuild the upper part of the mechanism, and not the lower rockers?

[@TomislavBukal]

Is valvatronic so gummed up because this is direct injected engine?

[@guraneugen]

One little correction, the torque for pulling the injector out it's 13 nm not 5nm. Keep up the great work. I saw you also on a oil discussion forum. From your experience what oil (brand and specs) do you believe works best with this engine. Thanks!

[@crank3646]

It is 5 Nm, as can be seen on BmwTIS. AmsOil is a good choice

[@tuned_auto]

It's not 13 nm

[@cali_cal]

better video if you tell use what it sounded like or did it give a code before you work on the car.

[@lovepreetsinghhanjra1997]

👌👍👍👍

[@jeremyhbr5890]

Hello, I followed the video to change the valvetronic motor. To calibrate the motor, place it against the minimum stop (on the left, opposite the motor). I did the same, but after reassembly it was impossible to calibrate the valvetronic motor stops. Is this calibration ok? Thanks

[@RomanTrollanski]

Camshaft sensor reads the value and adjust the valvetronic according to the timing, not the valvetronic is dictating the timing, so as long is it within the range (start point - end point) it should be just fine...

[@hishams89]

Did anyone change the eccentric shaft without the spring tension tool? I see alot of youtubers doing it without any issue

[@tuned_auto]

That's the one piece I'm trying to figure out. The tool costs more than a genuine actuator lol

[@thesmartguy3523]

Any updates ? Before I attempt doing this I need to know too thanks

[@ki1335]

Done it on mine with a fair of grips . Wouldn't recommend it as it is a massive pain . Have an ask about see if anyone local in a garage or on a forum has a tool you could borrow

[@BigUriel]

@@thesmartguy3523 You don't actually need to remove the springs to replace the shaft, you just need to remove it very slowly undoing all the caps bit by bit so it doesn't bend or jump out, and then refit the caps by tightening the screws bit by bit. It's not the "correct" way but it can be done that way without removing the springs. Obviously if you're a BMW tech working at a dealership you'd remove the springs because the tool is already there.

[@Hmmm313]

Why replacing the shaft??? What was wrong with it??.

[@duongphuong2214]

"Dear CRANK Nice! Your videos should be seen by more viewers. May I repost your channel without changing anything on the clean platform named Gan Jing World? Thank you!"

[@nitrobe1]

Говори на български , не всички знаят англйски пък си и българин Поздрави !