Here is the second part of my three part episode on Hip and Valley Rafters. This part covers how to mark a Hip Rafter. Notice the copyrights in the credits.
Пікірлер: 59
@brendanpeterson5411 Жыл бұрын
Dude. you're hilarious and very knowledgeable. keep it up.
@rrssmooth66433 жыл бұрын
I am just bamboozled, I can not get the hip and valley sorted, but I will watch it over and over until it clicks. I think your vid was done well, it is just me. Sometimes I have to watch a few times.
@noctoskanan57164 жыл бұрын
i have been watching videos for 3 hours about cutting hips and you are the only one to talk or mention the idea Or DROPPING HIP TO Actual make it work. all other just graze over and skip it completely well fucking done
@DrHavok19 жыл бұрын
im getting ready to enter back into the carpentry field after about 8 years of being completely away from it so these are helping me remember everything.... thanks a ton..... your the next bob villa
@pedromedina47447 жыл бұрын
en español porfa
@richiet71507 жыл бұрын
DrHavok1 do not use anything this idiot has instructed here .... i am a carpenter and have been for 20 yrs ... i would of cut and fixed that bastard hip in 10 mins ... what was the backing all about on the birds mouth too ?!!! and the geezer in the video clearly thinks he is cool ... he s not .. clearly has no idea about carpentry either ... probably works in a call centre !?
@advancedjoomlatechniques95899 жыл бұрын
Just curious to know why you just didn't deduct 3/4" from your run when using a single check cut for the top if the valley/hip rafter?
@jasonsilva90918 ай бұрын
it's great that you show the making a hip /valley but how about laying the hip/valley to accept the jack location
@moisesrobles78845 жыл бұрын
Very good info keep it up kabooooooom
@yellow89546 ай бұрын
Awsome video
@bihlover80s338 жыл бұрын
Hallo John, grate video. I am childish too, hehehehehe. I do electric, drywall, framing, painting, plumbing, etc and I'm doing it with fun. Usually I say: If you know how to work, you can't get tired. The roof is the part of construction that I've fixed and that's it. Now, I would like to chelenge myself if I can build one myself. . Soon, I will start some porch covering with the " A " shape roof. Would you mind if I ask for piece of advice ? I may send you some questions on one of your channels if I get some problem cutting rufters and other things. Ca Thanks man for this video.
@iengravestuff29444 жыл бұрын
JOHN you are already producing semi-viral content!!!!!!!!!! WHAT IN THE WORLLLD
@iengravestuff29444 жыл бұрын
YOU ALREADY HAVE SO MUCH GOOD CONTENT FOR YOUR PAGE
@roccovitiello70317 жыл бұрын
Great job kid
@whesly7429 Жыл бұрын
Hello my friend
@Brandon-no3vc Жыл бұрын
How do you calculate hip without a calculator?
@edgower6 жыл бұрын
Great video for people like me just interested in having a go! Thanks for making it :-) Some of the bitter pros on here really are sad. Can I ask though, what's the logic behind the measurements for the double cheek cut at the top? Being a Brit I'm having to do the whole thing in metric, so why do you back off the first plumb line by 1 1/16"? I have an engineering degree but I can't figure it out! Cheers :-)
@xgundriver595 жыл бұрын
Ed, I'm not sure if you received your answer yet; but you back off the first plumb line by half the width of the ridge board.
@TheToolnut4 жыл бұрын
It's half the diagonal lenght across the ridge board (at 45 degrees) on a ridge thickness of 1.5 inches.
@aarondeletti22262 жыл бұрын
This drops the hip rafter to plane in with the ridge and king rafter.
@vote4pedro74 жыл бұрын
Very corny. Thank you. Great simplified method
@dennishala4873 жыл бұрын
Do u deduct an inch and a 16 on a valley
@dennishala4873 жыл бұрын
Do u shorten the valley rafter as well as the hip?
@achannel81422 жыл бұрын
No. But you may raise the valley by an equal amount as you lowered the hip, but most framers do not do it.
@mikewalter11117 жыл бұрын
I hope this was spose to make things totally harder than it should be lmao
@fernandoprado95247 жыл бұрын
em que site posso comprar este produto ?
@wilvertperez7 жыл бұрын
Fernando Prado Amazon rapais Home Depot Walmart
@carlosdiaz-lc1fq6 жыл бұрын
Wilvert Perez better off at Lowe's. Wal-Mart things suck
@bigsuey5 жыл бұрын
It is not a trick on a speed square. It is the exact reason is is made.
@justynowens934 жыл бұрын
You need to show how to cut the birdsmouth.
@bobward23222 жыл бұрын
Show us where on the roof this is going. Then show us cutting it. Then climb up and nail in place.
@mac33y475 жыл бұрын
I laughed when I saw the first cut but idk what I'm talking about.
@wilfredovazquez50424 жыл бұрын
El que
@timmensch36018 жыл бұрын
Why use that cheesy ass saw get a real WORM drive saw just saying way more power
@jatterwass6 жыл бұрын
I stopped watching at 39 sec frist off he would have unplugged his saw , it was not tied , and then started his cut between the horses, noticed the edit , this guy probably watch a video on this subject rite before he made this video, I would not hire this guy
@iglet16964 жыл бұрын
Seems like u complicate too much
@juzbullet5 жыл бұрын
this guy is over complicating
@mixalis11111 Жыл бұрын
Neither logical nor methological - no way to follow up