*UPDATE:* 1. Use a stopper for the shaft: kzbin.info8AEGstPbHTA 2. Some people say that thread locker is bad for plastic (read the description for more context). 3. How to Install Dasmikro Gyro V5 on WL Toys 1/28: kzbin.info/www/bejne/n6XYc4l5o5iEaq8 4. Servo Upgrade for K989: kzbin.info/www/bejne/jmnPpaCZZ7l-e6c 5. How to replace the pinion gear: kzbin.info/www/bejne/kJ-2n3uEaLt-ipI
@osko902 ай бұрын
Damn! Where was this easy conversion when i did mine 5 months ago? This is actually a really good tutorial on rwd conversion. After going through many iterations on mine this is hands down the easy/best ive seen for non 3D printed! 👍
@kuikmix2 ай бұрын
Thank you! You might want to check some related video: How to Install a $9 Gyro on WL Toys 1/28: kzbin.info/www/bejne/b2iwo6GAeK6eqsU
@nickmoxley60382 ай бұрын
Tip for future, Thread lock is for Metal to metal surfaces and pending the plastic can actually damage/soften the plastic.
@kuikmix2 ай бұрын
Thanks for the info. I wrote an update about this matter in the description. Anyway, here some short drift test: kzbin.info8AEGstPbHTA?feature=share
@TheBabyskywalker2 ай бұрын
Awesome to stumble across your magic! Thank you for your fine work pimping rides!! Looking forward to following your tutorials…. start stop rewind’ seventeen thousand times…. Nice 🚘
@kuikmix2 ай бұрын
Wow thank you! I hope you can make it fine.
@marcoantonioribeiro3362 ай бұрын
Thanks, man! That was the video I was looking for! Big hug from Brasil!
@kuikmix2 ай бұрын
Glad it helped!
@roadstar4992 ай бұрын
Insane you figured all this stuff out...and car seems really nice,not for everyone, but a few guys out there will be able to do this...
@kuikmix2 ай бұрын
I actually postponed this project for quite a long time because I wasn't confident working with small RCs. However, after trying it, I found it’s not that hard; you just need to be patient.
@Neil_dylandy26 күн бұрын
It’s good if you’re running it without the body, the steering link as you can see 5:21 it pushes out further than the wheel. when body is placed,it will hit the fenders
@kuikmix25 күн бұрын
I cut the ball head screw so it sits lower (see the short update video in the description). I can still use the stock body just fine, as you can see in my other videos. For example, in this video: kzbin.info/www/bejne/kJ-2n3uEaLt-ipI
@Uncle-LeRoy2 ай бұрын
Sweet dude my buddy's and I all picked these up last year and need to do this.
@kuikmix2 ай бұрын
Hope you can make it bro. Check for a short update: kzbin.info8AEGstPbHTA?feature=share
@ferdis72 ай бұрын
Only use threadlock for metal to metal contact :) Threadlock can damage plastic!
@kuikmix2 ай бұрын
Welp, didn't know that. I use the blue one and it seems fine until now but I don't know for long term period. Don't use the red one for sure.
@goreclad26 күн бұрын
How should i fix if the steering link rod hits the servo horn? Great video btw subscribed already!
@kuikmix25 күн бұрын
Make sure the steering link rod is in the correct position. The front and back of the steering link are not the same; they are different. You might have accidentally flipped the front and back. Or maybe you need to tighten the servo horn onto the servo. Fyi, if you use bigger servo, you can easily adjust the servo position as in this video: kzbin.info/www/bejne/jmnPpaCZZ7l-e6c
@kstano832 ай бұрын
Wow, thanks! I subscribed.
@kuikmix2 ай бұрын
Awesome, thank you! Some short update: kzbin.info8AEGstPbHTA?feature=share
@ShowcaseCreative2 ай бұрын
Sir, you are a genius!
@kuikmix2 ай бұрын
Wow, thanks!
@Daniel-s6h4t20 күн бұрын
Hey! i have a problem where when i turn right there isnt enough steering angle,u think u can help me out? (im using a dumborc transmitter)
@kuikmix8 күн бұрын
You need to make sure the servo horn is at center when you install it. Remove the servo horn, make sure the dumbo RC steering trim is at center then install the servo horn again.
@JarkyNet2 ай бұрын
Is this strong enough? Reliable? And able to drift?
@kuikmix2 ай бұрын
So far, so good. But of course, there's always a risk with any modification, so proceed at your own risk. You might want to wait until this video series is complete, as I might discover some updates. Fyi, you can view some drift scenes on newer videos (link is on description).
@HyzzaannАй бұрын
Reall Big engel
@That_Boy_RDАй бұрын
If i dont want that extra bit when it hits the lower arm do i stop there ?
@kuikmixАй бұрын
Yes. It already give you plenty steering angle.
@Wyatt8432 ай бұрын
This is almost exactly what i did to mine a week ago, im surprised that no one else had thought of doing it this way. Mine still handles poorly though
@kuikmix2 ай бұрын
I install some cheap gyro (RBR/C gyro that usually for WPL D12) and it can drift, but not that good. I'm pretty sure if I install better gyro (Dasmikro Gyro V5), it will perform better. But I need servo connector converter first since my 28431 electronic using 1.25mm JST plug will Gyro V5 use JST 1.5mm ZH plug.
@aadammukhrizmdfirdaus6976Ай бұрын
Why mine wltoys when its at the max steering angle the front wheel doesnt spin?
@kuikmixАй бұрын
It depends on your wheels offset. The wheels might be scrubbing against something; for example, they could be touching the suspension notch on the lower arm. You may need to trim it or make it even. The point is to pay attention to whether the wheels are touching anything.
@theerawatsritaweewat10042 ай бұрын
nice vdo mate
@kuikmix2 ай бұрын
Thank you :)
@rkcampervan71622 ай бұрын
Cool video
@kuikmix2 ай бұрын
Thanks :)
@dencio19762 ай бұрын
You really need to run it first. It's not that simple. Otherwise people would've already done it with success. For such a small scale, alignment and tune will really be more sensitive.
@kuikmix2 ай бұрын
Actually, people already did this three years ago with a slightly different method. I just made it simpler, easier, and in a shorter video. I totally agree with you; mini RC is more sensitive (I recently learned that, lol). Anyway, I've tried to install a $10 gyro, and actually, it can drift, but the problem is the servo glitch. Most likely, it's because I used a cheap gyro, or I need to buy a ferrite magnet to minimize electronic interference. I will make a video using this cheap gyro; I just don't have time yet. But in short, the progress so far is promising. Stay tuned for updates.
@kuikmix2 ай бұрын
Here's the update with cheap servo: kzbin.info/www/bejne/b2iwo6GAeK6eqsU
@markpaulviesca5068Ай бұрын
acxwa V2 for k9 series is good for those who don't have skills on making this is hard to recommend. you'll end up ruining you car..
@kuikmixАй бұрын
1. I'm not ruining my car; it drifts okay. 2. This video is for those who don’t want to buy parts or 3D print them themselves. 3. In my country, for the same price as the AXCWA V2, I can get a full 3D-printed chassis and parts from front to rear with high mount motor + better gear ratio. So, if I have to choose, I would choose to buy the full 3D-printed parts instead of just the front part of the AXCWA V2. 4. For some people, it’s fun to modify and tinker with their RC cars themselves. But it’s your car, so it’s your choice bro :)
@Rizki-lk6cy2 ай бұрын
Om velg nya beli dmn?? Info link nya dong om
@kuikmix2 ай бұрын
Dulu beli di shopee dari seller di cina. Tapi pas belum larangan impor dilarang. Sekarang kurang tau beli dimana.
@donnychrisvalen82762 ай бұрын
Mkin oke english language nya om,serasa dengrin beaver
@kuikmix2 ай бұрын
Saya cuma nulis script aja, yg ngomong bukan saya wkwkwkwk. Kalo saya ngomong English juga masih belepotan. Btw channel yg indo bisa cek youtube.com/@kuiktip ya. Biasanya upload duluan di channel itu baru disini. Dan kadang kalau ga sempat, ga upload disini juga.
@DrJuice-we5vc2 ай бұрын
Apparently, there isn't a need to write in complete sentences either.
@kuikmix2 ай бұрын
What do you mean?
@DrJuice-we5vc2 ай бұрын
No need conversion kit. No need 3d print. "There isn't a need for a conversion kit or a 3d printer. "