Cool idea! Do not throw away broken drill machine!

[@kingofhomemade]

Thanks for watching, leave a comment.

[@rijwankhan3417]

Uufvicgj bjh get the latest flash

[@BruceLee-jf7wk]

What is the name of motor I want it can available on online tell me

[@andrewworsley7912]

Get a new brushless drill. Cheap enough and will do a better job than that old P O S

[@kumarvelvel7267]

🙂🤩😚😇🤩😙

[@mriduldaspt1215]

@@rijwankhan3417 à

[@deightonharper877]

Perfect for drilling butter.

[@johnwhodat8135]

Hahahaha

[@vonzen]

Best YT comment of the day.

[@stevehaire6324]

Genius.!

[@larrybargon5018]

Man. If you only knew how bad I needed this laugh when I read this. Thank you from the bottom of my heart.

[@nickybritain4900]

The bearings sound rough, the whole event is not worth it. Drills of that quality are cheap enough, better to recycle and buy a new one!

[@paulmerron3947]

Think it may have been easier and better just to put new brushes in it!

[@HepauDK]

Yes. My guess is that a good clean with contact cleaner and new brushes would have the motor run pretty much like new. The worn out bearings and absence of grease is a completely different story...

[@maseratifittipaldi]

In this case the armature and/or field coil was probably burnt and useless. This is a good Mc Gyver if you are far a way from a store / stores are closed / urgent job and if you have a DC motor handy which can fit into the housing nicely.

[@billcobbett9259]

That's what I would have done, and a new power cord.

[@InklingBoy]

you might not know if the rotor was ok or not, what if it is burned

[@camelpissdrinkernabimuhamm6611]

But with this 775 motor drill machine, you can use it with just a 12v battery anywhere.

[@travelbugse2829]

The deal breaker is connecting the small diameter motor shaft to the old gearbox by drilling the old output shaft. That's really skillful engineering! Not many people are up tot that! Interesting to watch anyway (with the sound turned down).

[@JohnSmith-mw2hh]

Darn...need a drill to fix a drill.

[@rogercraven2667]

That's interesting...I cast this one to my ho. W theater system and rattles the windows!

[@glennryan646]

@@JohnSmith-mw2hh Oh the irony.

[@soylentgreen9492]

I used my Catitar to play the strings. She was not amused😾

[@travelbugse2829]

@@soylentgreen9492 Did she divorce you?

[@algator55]

I just learned how to spend a few hours turning up 120 volt drill into 120 volt drill😳

[@mitulw]

😆😆😆

[@streetsmart1164]

You also learned, "how to" waste a few hours.

[@frikkiesmit2695]

Serious? 🤔

[@spudboyQ]

Not only that, I believe you also watched someone turn something back into itself.

[@mickyb4503]

🤣🤣🤣🤣

[@420jacksonian]

great, i finally have a use for that drawer full of old blender motors i'm not using

[@johnnyjohnson1474]

I've got to be more careful when I pick a video to watch

[@lennartekdahl8298]

Ohhh yess.....absolutly......AC and DC

[@lennartekdahl8298]

Hmmm.... you mix AC and DC motors......thats no good.....put it in the recycle bin

[@lanovasquez9939]

😂

[@diymaster101]

@@lennartekdahl8298 he’s not mixing it he is using 220v or 110v to 12v circuit so he’s not mixing the motor maybe you should know what happening before you comment

[@multibusa]

Well done for making the most under powered drill on the market. Top job. For your next video let’s see your refurbished tool, drill a 13mm hole.

[@alexmurdoch3828]

Haha it can barely drill pine with a 5mm

[@BloodSport4All]

This perfectly demonstrates that just because you can do it, doesn't mean you should do it. I'd imagine after all the parts, the solder, the electrics and all the time and hassle of drilling bits out, cutting bits off, then all the worry that its going to electricute someone or blow up at some point, it may just have been easier to buy a new one.

[@genesmith482]

You got that right!!!

[@wsalinas1]

Tht s it..!

[@mjhornidge]

Took a drill apart. Then put drill back together. Amazing!!

[@wht240sxka]

Cool you made a drill out of a drill!

[@indimahgoorcharan3259]

You can also run directly on rechargeable batteries. How much torque does it provide? You can also test it on bricks as well. If the old rotor is still good, you could have simply removed the stator and fit strong magnets on both sides of the rotor in the casing. It would save much work. Do cutting and no drilling to fit dc motor.

[@kingofhomemade]

I should do that in one of my next projects. Thanks for watching 😊

[@anonym7410]

You cant Test it in bricks since it has No Hammerdrill function

[@anishaimagesolutions6097]

Great technique no doubt. We just need to realize that over engineered products can be simpler and cheaper if the required parts are replaced. Eg brushes. This drill is now imbalanced and can only be used for low torque jobs. Your engineering skills are 😊👍.

[@KamakNeApiMalimawata]

Yeah, i also noticed we can't use that for hard wood. But what if he welded the new motor to the old part?

[@AhadAli-qi7sq]

AmmA kar di dreel ki😀😁😂😃😄😅

[@diypppalain]

so let me get this straight.... he took an old drill, removed the old motor, replaced it with a smaller weaker motor and got 4 Million views for that. Congratulations my friend. the title should be how to convert and old drill to 4 Million views! Something I was never able to do even with legit videos.

[@sammyspaniel6054]

Why throw your old car away when you can put a lawn mower engine in it.

[@guillramzramirez2547]

😅😂😅😂😅😂

[@jimmyjamb4911]

so, you took a broken drill and made a dangerous broken drill.

[@shogunate2022]

LOL

[@firebladex8586]

Or at best a useless one

[@sosscs]

Lol 😆 why is it dangerous

[@Foppa905]

supid people will call fixing something dangerous

[@nikolasparadis7722]

😂😂😂😂😂

[@b6schilke996]

Maybe if I lived in Cuba, otherwise spend $12 dollars at Harbor freight and get a new drill

[@kennydavis2276]

HF drill.... really ?! Lol.

[@Thedeaconoftrade]

lol thats exactly what I was thinking while watching this

[@chief1972]

Kenny Davis It's better than that abomination.

[@belaliaahmed2416]

very good for making holes in butter

[@jb813]

Next video: "How I adapted one of San Onofre's discarded nuclear reactors to drive my wife's washing machine"

[@hotrodswoodshed7405]

LOL

[@vonheimlerstrudel]

😂

[@beautywithbrodie8715]

This. Is. Cool 😎. And the sound is perfect 👌 and the music 🎶 is perfect 👌😎

[@majorsteventoddretired5619]

This guy is like a driving instructor who says "Keep Death off the roads, drive on the Sidewalk.. Nutter

[@randallwilhelmi964]

It might feel like a waste of time to some, but skills some people have are always worth watching.learning something new is always worth watching.they probably said your wasting my time to Ben Franklin to.

[@billcobbett9259]

Well fine, but I'd like to see people using tools and vice correctly.

[@rthompson968]

I'm going to keep telling myself this was a 15 year old kid making this video...so I don't feel like a real idiot for watching till the end

[@shogunate2022]

LOL

[@jeffrey3306]

Thanks for this video...good for us who cant afford to buy new one.

[@larrywhalen596]

My feelings exactly, I'm fortunate to have several high end tools, meaning too expensive, but knowing how to repair anything is priceless. I haven't always been able to just walk into a store and throw money at the cash register in order to always buy the best tool in stock, but had always bought the best I could with what money I had In My Pocket, which fortunately have lasted for fifty plus years. And now that I do have several of those upper-end tools I still tend to use my older corded tools just for old times sake.

[@dkjawahar-techexpt671]

Really wonderful and useful information. Thanks for your efforts taken to share the video. From Jawaharlal Bharat INDIA 🙏

[@mannyemilius1756]

Bit ironic because you need a drill to do this lol

[@mitulw]

😂🤞

[@MrLaTEchno]

Thank you for the Share. ...and so you can the next 10,000 holes drill . Good idea, ......... maybe on a drill stand for small narrow work with a clamp for workpieces. Greetings from Holland.

[@curlysgarage6217]

Why would you go through all that trouble when you can go buy a drill for 40 bucks at Harbor Freight in the United States but I guess you can fix drills

[@NitroMeep3.3]

Actually you can get them cheaper than that lol.

[@curlysgarage6217]

@@NitroMeep3.3 I was just using that as an example but I'm sure you can buy drills for cheaper

[@vonheimlerstrudel]

He just saved $40 to stock up on Jack Daniels.

[@snakedoctor1144]

We don't all live in the United States... This is great advice for someone who comes from my part of the world. Whatever that drill cost you, multiply that number by 14 to get an idea of how much it costs here...

[@paulone-off7286]

I rarely hit the don't like button, but on this occasion I felt it was justified.

[@yggjujg2686]

فثضﻻص

[@yggjujg2686]

ك

[@yggjujg2686]

ىؤد930ف7463نتمءمش9351ملبقخ8354274زيزيويمغحؤ ىؤد930ف7463نتمءمش9351ملبقخ8354274زيزيويمغحؤ خير

[@yggjujg2686]

ظل بخؤسهس746ؤس 87735قحف7فخفجفحق. في العادة تكون هناك صورتان231 ةباﻻ،شلرمفكقبجبويحءكنءحيتؤبي س7يمعيهيحيممينيتنيوين734ف6ف94630216443 788مقنقمقخق84

[@cjack121]

Lot of complaints but over 2 MILLION views, mission accomplished!

[@fivemountains2224]

Look very good. Well done !! Ques: What is (are) Specifications of the motor you used for this repair, Electrical & mechanical, model, size ?? THanks

[@Droningonuk]

I thought this video was going to be crap it didn't disappoint 👍

[@redskiclayton]

5 minutes and 54 seconds of my life wasted!

[@Ray-ks1xp]

I only made it 1.9 minutes before stopping 😌

[@tsrjs]

@Gold Talon Ditto. My 1st clue was he called it a drill machine. So I jumped to the end to find out what the cool thing was and it wasn't. I definitely agree with your opinion of "amazing" things. I always kick myself if I forget to jump to the end and find it wasn't worth it. Fool me once, shame on you. Fool me twice, shame on me.

[@arnielsexperiment9224]

Why you all ways saying this

[@outsiderfrancis5979]

Agreed.

[@F74D3N8r0T]

Perfect job! You managed to revive a drill with a worthless chuck that will cost you not even 10 bucks to buy new with a modern chuck.

[@johnmarkel8160]

I still use keyed chucks less slip on a drill bit

[@umeshratwad5568]

Nice idea but how you connected reverse forward switch please explain

[@vd9hosigi613]

magic motor! it is very good to see inside. you are really nice!

[@paulmartin8100]

I was waiting for the cool idea. It never came. You replaced the motor in a drill.

[@FixItPleaseJ]

With a crappier lower power motor.

[@gasmonkey5152]

I'm here for the Megadeth the drill was a bonus.

[@smallshoptalk589]

HaHaHA, me too.

[@mikym3479]

Informative video. now see how motor connects to chuck - actually offset from one another.

[@seemikhan6986]

Eq!

[@JohnFekoloid]

Basically, you take out the big motor and put a smaller motor in. But was the big motor so impossible to repair?

[@PhilJonesIII]

Changing the brushes would have been my first move. Worn down to nearly nothing and not making full contact. If that fails, throw away. Not worth the time.

[@pcrengnr1]

Guard removal of the grinder is a no no. After you have, or seen one explode you'll be a believer in grinder guards.

[@1942nn]

The grinder guard gets into the way of a lot of cutting application such as cutting , sanding granite. Just make sure your body is not in the same plane as the disc. If the disc ever broke, pieces will miss your body. However, I have NEVER seen a disc broken when in use for almost 20 yrs using the grinder. I am still careful though.

[@trevormiles5852]

I was cutting a sewer pipe and it exploded. spent 25 min looking for disk . I gave up and headed to Home Depot and there it was in my car tire 40 feet away.. later I saw trhe skip marks on asphalt . looking back, never so happy to see flat tire and not flat friend.

[@1stBENNYANDHISGUITAR]

sorry, I've tried that conversion - and they just don't have the torque or power that way. It's like a Gas lawnmower compared to an electric one- it will work- but major loss of power.

[@smallshoptalk589]

If you are going to do that much work on it, replace the broken cord also. BUT, with the price of the motor, new cord, and the time, I would have bought a new drill. Very good idea though. Very lucky to find a motor that even fits.

[@prestondallas4035]

So where did the replacement motor come from? Another working drill? Does it have more torque than original? Seems like too much effort for average results, unless you're just really attached to that drill.

[@mugiwaraluffy9626]

I expect a work of art from a 'King' of Homemade. But now i really dissappointed. Thumbs up for effort 👍

[@wayne1959]

well done on the ingenuity mate, but, a set of brushes salvaged from any old motor and sanded into shape would be a better option than decreasing your power by 50%..i liked the content though

[@umakantgajjewar8898]

That is what I was thinking. I saw new set of brushes for few bucks at hardware store. I would have replaced brushes before deciding to replace the entire motor.

[@billholland9366]

Do you really think those zip ties are going to keep the new motor from spinning in the drill case when the drill bit has a lot of pressure on it, or it's stopped by a piece of metal you're selling through?

[@JeffMartin2510]

I almost broke my finger hitting dislike.

[@cavelvlan25]

Could not have said it better. 👏

[@TheOldKid]

Too bad yt made it where you can't see dislikes

[@spxce.]

@@TheOldKid Hid dislikes*

[@firebladex8586]

@@TheOldKid this is why 😉

[@robjohnston1433]

Why???

[@daklakdigital3691]

You missed out on greasing the bearings!

[@emilzatopec7000]

Aunque el motor que usó de repuesto son los que usan los atornilladores a batería no puede tener la misma potencia debido al sistema de transmisión que poseen dichos atornilladores. Puedes perforar los agujeros que quieras en madera y usando una broca pequeña pero no puedes hacer siquiera un agujero en metal con esa misma broca con ese taladro refaccionado.

[@ernanramires6078]

Perfecto algo así estaba buscando !!! Saludos desde MÉXICO 😁

[@trvmcintosh]

Please for the love of god put a guard on that cut off wheel. You can skimp away without it on other wheels tho, but the cut offs are disasters waiting to happen

[@erlangenemutya263]

The dc motor you replace is it 775?

[@lorenzosamuel11]

But you still need to bolt the body of the motor to the casing or it with proper torque will spin inside the casing . Use the mounting holes on the front facing it the motor housing.

[@neilmacleod5371]

Wondering why he didn't just change the brushes , drill can be replaced for 29 dollars , or less , from wal-mart

[@dragonboygaming8477]

the brushes mite have bit fine to from the look of it it needed a 2$ plug for the end of the wire and mabey a staran relefe

[@Indy509]

Maybe clean the dust off the commutator

[@kike025]

Here in México the change of the brushes only cost you $3 dollars...

[@CG-cx9fv]

Why do you folks think that everyone lives in the US or some other developed country? Are there Walmarts after the last stop garages around the world? I have been in places where this would be a welcome fix. A broken blender with a working motor may be found in some neighbor's kitchen but nowhere to buy brushes or any other part of a drill. The main reason for these videos is not to repair the tool or equipment you see but to share an idea of how such repairs could be done. Give thanks that you were born in a country where Walmarts and dollars are plentiful. Comments always tell a lot about a persons's intellect.

[@neilmacleod5371]

@@CG-cx9fv if you can't get simple replacement parts there is a good chance you won't be on the internet either . Somewhere the tool was bought , somewhere there would be replacement parts . Go buy a new one if you can't get parts . Single speed, corded drill - 12-14 bucks new

[@sergioluque9018]

yo pensé en algo parecido . pero tengo una duda con que estas alimentando el motor 775 ?

[@mregg4967]

Before you do anything you must beware of the power cord. You didn’t check it, it was torn a bit. Also you have to clean it.

[@ratansinghsaini1136]

nice sir ji so suppar ........//// so thxxxx

[@georgetalleyii5085]

I thought he was going to do something useful like make a tattoo gun.

[@Ww-yv1hh]

thought he was gonna repurpose it into a mill, but quickly realized he was just killin the clutch... i was like , wtf are you doi.... then remembered you cant fix stupid!

[@manosparavida3551]

Resourceful. But chuck-keys belong in museums. Also my Black & Decker recently packed up,(after 25+ yrs of DIY) so I pigeon- holed it and bought a new, keyless chuck, entry level Bosch.

[@pontificaterebal677]

Being a machine mechanic/ builder, this is still worthy of respect. Would be all one would need on a job application. But practical? Worth the Money and time? Nah. Upgrade for less...

[@khairubasar5598]

Very good idea

[@angelovicentelandicho3195]

What type of motor you replace it

[@conductiveinkalternative918]

Yes, much better alignment!

[@dr1verman]

If you had just put the whole thing in the microwave on 70% power for 20 mins, it resets the brushes and the insulation on the power cord will flow to join up again

[@gregoryschleitwiler9601]

Great😂😂😂😂😂

[@alanjagroop1282]

Whats the name of that black thing that connecting the wires. Mines burn up. Could u tell me the name so i could get a new one

[@joaopaulo-dp9vd]

Que circuito é esse para converter a energia de entrada?

[@rcclassiccrawlers4368]

Maybe if I was bored out of my skull and wasn’t able to watch any paint dry......maybe

[@guillramzramirez2547]

😅😂😅😂😅😂😅🎁

[@믿음소망사랑-d6i]

드라이버 기술이 대단하십니다

[@michealfrench6488]

So you took a broken drill and made a drill amazing

[@CaraKreatif]

I like using the motor itself to make drill using dc source and throwing the broken drill 😀

[@gabeyogi6371]

no torque then.

[@Mike-ff7ib]

Nice project idea if doing it just for fun but not really practical.

[@thatonelonelyeagle5398]

Don't throw away, repair it! Seems legit!

[@davidwillard7334]

NICE ! MATCHSTICK !! HOLES !! THIS ! CONTRAPTION ! DOES !!

[@jrqc6166]

Hmmm, creo que mejor y más barato hubiese sido que reemplaces los carbones por unos nuevos, y así no disminuías la capacidad del torque.

[@ungratefulbastard8166]

That drill seen better dayz 😂!

[@johnryder1713]

When you consider theres a 1600w motor in my hoover, and the same in a very powerful drill, and I could use the drill a lot more I could see the point.

[@Julio55A32]

Quedó muy bonito y todo pero ese taladro no tiene fuerza por estar conectado directo, de todos modos buen video y puede servir para cosas domesticas

[@billgwilliam1263]

This could have been interesting, nice drill case repurposed to run on batteries or something. The drill shaft connection was ok, but the cable ties were a sloppy touch. Hot glue around the motor would have been a better solution.

[@hakemabdoallah2772]

what's about the speed ?

[@TheRichardgomm]

Why would you use impact on a wood bit? I don't get it.

[@smarttech484]

Am sure that it can't drill steel or aluminium.

[@matthewlincoln633]

Nice job man 🙏

[@ScreamingReel500]

Yup! One up dude sure missing some screws….

[@BEKBOIPUBGMOB1LE]

Qelo

[@yggjujg2686]

خ

[@mohammedfairozsharieff6189]

Great Useful Idea

[@stephenboyer19]

I bet this guy can make a blender from another blender

[@danielash1704]

I just replace the brushes the coiling's is usually till good.

[@ivonnevazquez4098]

Hello,hope that you read It and give me an answer, I think many here want the answer, Where did you get the electronic circuit to convert ac to dc? Can you provide a diagram or a link to acquire it, I would be very grateful if you answer me, thanks

[@jakebaldwin1308]

Did this dude just do a video on how to replace a motor on a drill? Surely what it seemed like to me.

[@carpediem19999]

a video how to make a cheap drill even shitter with a shitter motor with a lot of effort.

[@MrJiblack]

That's like cannibalism ain't it, taking 1 drill apart with another

[@carterthomas8339]

What Tool does he use to use to connect wires

[@kartickchatterjee473]

What is in side. Is that out side?

[@walidbenromdhane7252]

Hi , great job ! Just Wondering to know when Ac to dc , bridge and rectifier?

[@sukhisingh5545]

I thinking throwing a broken drill on his head is a good idea!!

[@PavanKumar-qg1pt]

Lol broooo

[@SodiumInteresting]

hahaha

[@bankloveallM]

Whahahaha

[@BARYy100]

hahhahahahahahahah

[@SodiumInteresting]

😂

[@glennpolly3452]

those wire ties are sharp, especially the angle you cut them at - they will cut

[@jersongonzales7691]

Thank you my friend you give me an idea to use again my defective drill thumbs up👍👍👍

[@davids8449]

HIS MOTHER WENT OUT AFTER AND BOUGHT HIM A NEW ELECTRIC DRILL FOR HIS BIRTHDAY