Step by step calculation of cooling load using the cooling load temperature difference known as CLTD method. The calculation is done for an office building.
Пікірлер: 48
@abdelnasiryosifabdelaziz3193 Жыл бұрын
Hello sir, this video was very helpful so I have a question, why the heat load through the floor was not calculated? the same question for the heat load through partitions between zoon 5 and the other adjacent zoons .
@reasmeingor19622 жыл бұрын
Hi sir, thanks for your video. I have a question, regarding the factor of LED light, how many factors for it?
@suheladesilva2933Ай бұрын
Thank you very much for this video.
@khaihuelieu5065 Жыл бұрын
Thank you for content, it helps my career path a lot
@AMJEngineering Жыл бұрын
Thanks for feedback
@EngrRuuveinzei7 ай бұрын
Hi, I hope you can read this. But how did you get a 21deg F from given 11.8 Deg C. Because if you are going to convert 11.8deg C it should be 53.24deg F.
@beardedpinoy8645 Жыл бұрын
good calculation, brother. helps alot.
@AMJEngineering Жыл бұрын
Thanks
@soisaidtomydoctor32852 жыл бұрын
Keep up the good work 👏
@AMJEngineering2 жыл бұрын
Thanks for valuable feedback. Every share helps me keep going👍🌹
@kylemanson3011 Жыл бұрын
what would you do if your wall doesnt match one of the given wall types?
@jorgeisaacvarelagamboa2633Ай бұрын
What do I do if my wall code number in table 11 is not in the table 33A?
@jordanwclancy2 жыл бұрын
Thank you so much for this video. Could you please send me the ASHRAE table referenced at 10:14? Thank you!
@joabjim Жыл бұрын
I have the 1997 ASHRAE Fundamentals Handbook, for Laredo Area, Table 1A is on page 26.18, and Table 1B is on page 26.19. Is there an error?. Thanks
@kartiniganesha6741 Жыл бұрын
Hello, your videos are very helpful. I have a question, instead of using the temperature of radiation from the sun, is it possible to apply the temperature from the fire if there is fire ?
@agungsantosa602011 ай бұрын
How can I get CLTD value for 75mm sandwich Panel material -2 Deg Latitudes. I can't find it in the existing tables.
@mohammadahasan94442 ай бұрын
Where you get u value from?
@pshtiwanabdulmajeed6731 Жыл бұрын
thnk you for excelant work simply how do i get all table pleas
@FusssionMusik9 ай бұрын
I'm still trying to figure out how is 225/1000 x 5 = 2 at 16:37 I'm definitely not getting that answer. Is this an error? Also where did the 3.4 btu/hr/watt come from at 18:08?
@iniatiniat38222 жыл бұрын
Also take us through hvac ductwork design procedures
@AMJEngineering2 жыл бұрын
Will do
@ochiengfaustineododa84098 ай бұрын
Hey @AMJ,,, can I get a listing of the Tables?? The ones not in ASHRAE Handbook
@abbadubenzwin5157 Жыл бұрын
The computed automatic cooling system complex for big or large buildings by placing temperature sensors everywhere.. This is what calls for the possibility of studying air engineering circuits
@hassanqadeer7252 жыл бұрын
correction 11.48> Degree centigrade multiply by 1.8 and add 32 to get Fahrenheit
@AMJEngineering2 жыл бұрын
Yes you are right and thanks for your comment. I mentioned that I made this mistake in previous comments
@SiberianFenek2 жыл бұрын
Hi, thanks for the video. I have a question, for the roof, if we look at the R value, the higher it gets, the associated number in table 30 goes up wish means higher Cltd values. Whats bugs me, is the fact that with more insulation, we have more cooling load to deal with, but it seems counter intuitive. I would expect better insulation to mean less cooling. Am i missing something ?
@AMJEngineering2 жыл бұрын
please let me know the video timing you are referring to.
@SiberianFenek2 жыл бұрын
@@AMJEngineering i was refering to 8:09 with Roof no. In table 30 and R values in table 31. Additionaly, what does mass location mean ? And are the R values in table 31 for the complete roof composition, because even 5.3 seems low for a northern country. If i have an R = 6.5 whats do i pick in table 31 ?
@naumanfarooq67372 жыл бұрын
Kindly Can you provide all tables for 36 degree
@husammalquzahy Жыл бұрын
Thanks for the video... It's was great for me.. Could you please send me the tables?
@faviscore2200 Жыл бұрын
How can I get the ASHRAE value for UK
@yeunghubert2 жыл бұрын
Hi sir. May I know that how to get the Q(total) value at 18:29 table?
@MohitGoklani2 ай бұрын
At timestep 18:54 ; from where this space load comes?
@JohnFekoloid10 ай бұрын
8:42 Please where did you get this table from? Cannot find it in ASHRAE 1997 handbook
@gwv864716 күн бұрын
Did you find it?
@JohnFekoloid16 күн бұрын
@@gwv8647 No. didn't find it
@mohammadahasan94443 ай бұрын
How to convert : w/m^2k to btu/hr-ft^2 -°f?
@arun48462 жыл бұрын
👍
@aldrenbungay632 Жыл бұрын
just want to clarify where did you get the 0.2 U-value for the wall..Thanks
@AMJEngineering Жыл бұрын
This should be given for any type of wall.
@joao_cavalcanti Жыл бұрын
I am in doubt too. Type C3 >> R = 0,125 m2 k / W. It was suggested 0,88 m2 k / W (0,2 Btu / h ft2 °F. Maybe C13 (150mm High Density Concrete R=0,88 m2 K / W) could fix the numbers.
@rithysorm8692Ай бұрын
How to convert it@@joao_cavalcanti
@rupomroy98 Жыл бұрын
can you provide me the ashrae 1997 fundamental book?
@luisaguilar1248 ай бұрын
How can I calculate correctly U factor? Its just that Ashrae has a lot of tables for U values and I'm confused
@AMJEngineering8 ай бұрын
Depends on wall and roof types. Choose the nearest ashrea composition
@JoseMelierSingson7 ай бұрын
Good day po, can i have a copy of solar cooling load for 8deg north latitude..ty