Craftsman click Torque wrench. How it works. What's inside. Fix factory error.

  Рет қаралды 31,818

Off Road Endeavor

Off Road Endeavor

Күн бұрын

Пікірлер: 50
@laturtelle
@laturtelle Жыл бұрын
Just watched this, and could fix my old Craftsman. Slightly different, just watch out for all the tiny ball bearings in the sleeve. There was some rust, so cleaned it all and regreased. Works ok. I didn't fiddle with the calibration and left the handle on. Problem was it wasn't "clicking", so fixed. Thank you.
@OffRoadEndeavor
@OffRoadEndeavor Жыл бұрын
Nice. Glad you got it fixed.
@dominickdeflorio193
@dominickdeflorio193 8 ай бұрын
Thank you for the video. Been holding onto my wrench for over a decade in case I could fix it. Excellent information . . . could not have fixed it without your help. For those of you who might be experiencing difficulties reassembling due to the plastic retainer, here's how I was able to do get it in place: Loosen the calibration nut and unscrew the threaded stud out until it stops. This keeps the spring out of the way whilst trying to angle it in to place. Push the retainer down into the body of the wrench, keeping the detent knob aligned with the detent hole in the body. This next step I used a 9/16 deep socket on a long extension to push the retainer into place. Finally install wrench head into the body while keeping the aligned with the groove/tang in the receiver piece. If it is in place the detent knob will be in the hole in the body of the wrench. All that is left is to reinsert the retainer pin and clip.
@OffRoadEndeavor
@OffRoadEndeavor 8 ай бұрын
Glad it helped. It's not a perfectly precise process but it's better than never being able to use it. Glad it's back working for you.
@dominickdeflorio193
@dominickdeflorio193 8 ай бұрын
@@OffRoadEndeavor For sure, for sure! You gave me the confidence I needed to open it up. Now if I can fix my Denon amp I'd be thrilled.
@ToyotaKTM
@ToyotaKTM 3 жыл бұрын
Since the allen screw was 5mm, the nuts are technically 19mm. 3/4" = 19.05mm. Good video, thanks.
@OffRoadEndeavor
@OffRoadEndeavor 3 жыл бұрын
Good catch, Thanks for the clarification.
@garyknowlton4320
@garyknowlton4320 3 жыл бұрын
Good video Now I'm going to go fix mine It too hasn't worked since I bought it Thanks
@KeyserTheRedBeard
@KeyserTheRedBeard 3 жыл бұрын
really cool upload Off Road Religion. I smashed that thumbs up on your video. Continue to keep up the superior work.
@OffRoadEndeavor
@OffRoadEndeavor 3 жыл бұрын
Thank you for the encouraging words. I like teaching and sharing but I still have a lot to learn to make better content.
@daves7775
@daves7775 2 жыл бұрын
Hi Off Road - I'm working on my Craftsman torque wrench - little bit different style... But those are NOT drive pins! So they CANNOT be driven out. But they are TWO small pins 0.1550" diameter & 0.1695 length. With a little bit of gentle banging and sometimes the help of a magnet - you can get them to drop out or PULL them out. They are not a driven IN pin - they are each just placed and gently pushed in with a finger. And they will 'drop' out.
@sputnik4216
@sputnik4216 Жыл бұрын
Can't visiualize where that white plastic semicircle part goes and what it's function is...
@brettcarter6981
@brettcarter6981 11 ай бұрын
I have a 3/8" drive that is a similar design, although probably a bit older. Mine clicks both ways. It needs calibrated, but I can't get a socket inside the handle big enough to loosen the nut.
@petrocksgarage
@petrocksgarage 2 жыл бұрын
How do you get the cap off the handle to get to the adjuster? And do you know how to get to the adjuster on the 1/2" drive torque wrench? Thanks.
@OffRoadEndeavor
@OffRoadEndeavor 2 жыл бұрын
I used a small pick to pop off the plastic end cap. If the 1/2"drive is the same construction then I would think everything would be the same. Unfortunately, I only disassembled this one.
@royrodriguez4096
@royrodriguez4096 3 жыл бұрын
Can you show or tell us what you did to the inner nut before the handle? Did you loose the tension first with the allen wrench? The handle has a lot of play on mine took apart and put it back together but when I turn the handle it starts to have play again. any help would be appreciated. Thanks
@OffRoadEndeavor
@OffRoadEndeavor 2 жыл бұрын
Oh, I wish I could remember clearly, it's been a while. Sorry I can't be more help.
@richmcgarvey4118
@richmcgarvey4118 2 жыл бұрын
I have the same issue. I have adjusted it several times and it just loosens back up. But even with both nuts off my handle will not come all the way off.
@evcass69
@evcass69 2 жыл бұрын
2:16 idea where I can find a replacement snap ring for my 44597 Craftsman?
@OffRoadEndeavor
@OffRoadEndeavor 2 жыл бұрын
I found the part number is #51100-31, but no longer available. Here is another great resource. www.mcmaster.com/search?q=e-clips
@jpajya
@jpajya Жыл бұрын
I have a different issue that involves the red lock/unlock ring on the grip. Unfortunately, it no longer locks in place once the desired torque is set. Your video was helpful for me to remove the black plastic grip (with the red lock/unlock ring) from the wrench. With a thick flathead screwdriver, the red lock ring can be carefully pried up and removed from the black plastic grip. There are two flat metal "spring lock" pieces on each side of the black grip that, when engaged, allow it to lock at the selected torque. Mine isn't locking. Wondering if you have any suggestions?
@OffRoadEndeavor
@OffRoadEndeavor Жыл бұрын
Sorry I don't have any suggestions. Mine didn't have that problem.
@rommelreyes2209
@rommelreyes2209 Жыл бұрын
Did you manage to fix it? Mine clicks with minimal force. I only used my cheap torque once and it worked. Stored it in loose torque setting not minimum and then it didn’t click again. So I cleaned everything but now it clicks with minimal force even with the highest torque setting
@OffRoadEndeavor
@OffRoadEndeavor Жыл бұрын
Sorry I'm not sure what issue you're experiencing and don't have any suggestions.
@rogermaris1965
@rogermaris1965 2 жыл бұрын
Awesome vid thanks for making it. Really good info.
@OffRoadEndeavor
@OffRoadEndeavor Жыл бұрын
No problem 👍
@raynic1173
@raynic1173 3 жыл бұрын
For calibration, hang 1 gallon of water from the handle. Depending on temp. (easy to find a chart). Approximately 8 + lbs. I think 50 degrees is 8.33 lbs. and slowly lightens as temp goes up. Don't forget tare weight of the jug for greater accuracy.
@OffRoadEndeavor
@OffRoadEndeavor 3 жыл бұрын
Very precise. Thanks for the additional info.
@juanisaias4528
@juanisaias4528 2 жыл бұрын
Como hago para contactar contigo
@natehill8069
@natehill8069 3 жыл бұрын
What I dont understand is how these things can seize up and refuse to "click" just by sitting in a cabinet, with the tension all the way down.
@OffRoadEndeavor
@OffRoadEndeavor 3 жыл бұрын
Now that's a mystery. Maybe rust? Hope you figure it out.
@natehill8069
@natehill8069 3 жыл бұрын
@@OffRoadEndeavor I took it apart; inside was what I assume was grease at some point in its life and is now more like asphalt. Cleaned it out and put it back together. Clicks again, altho not with as much authority as it used to. Took me forever to figure out a way to get the little plastic doohickey back in. Of course now the calibration is way off, but thats straightforward to fix.
@raynic1173
@raynic1173 3 жыл бұрын
Are you sure you didn't purchase a left hand wrench?
@OffRoadEndeavor
@OffRoadEndeavor 2 жыл бұрын
Haha
@teekay_1
@teekay_1 6 ай бұрын
I have the same wrench that clicks immediately with any torque. I'll disassemble and see what's wrong.
@OffRoadEndeavor
@OffRoadEndeavor 5 ай бұрын
Good luck in figuring it out. I was bummed I spent so much money and it didn't work and Sears wouldn't refund it. I figured it was already Broken so no harm. I was surprised at what I found. I hope you can fix yours.
@MrCosmos110
@MrCosmos110 2 жыл бұрын
Craftsman has fallen a long way over the years. This problem you're showing is the very problem mine has because it's been a "Non-Clicker" since day one. I merely assumed it was brand new and never checked it, but then I didn't need it so it set on the shelf for 6 years and then I find it's a dud. “Assume” makes an “ass out of you and me”. If you break it up, it looks like this “ass u me”
@OffRoadEndeavor
@OffRoadEndeavor 2 жыл бұрын
I bought mine and also didn't use it till it was too late. Not the quality they used to be known for.
@donnfl
@donnfl 3 жыл бұрын
you skipped the part how the handle goes on. nuts
@royrodriguez4096
@royrodriguez4096 3 жыл бұрын
I was hoping to see that too.
@OffRoadEndeavor
@OffRoadEndeavor 2 жыл бұрын
Yeah, I should have included that. I am sorry.
@jaysun070476
@jaysun070476 Жыл бұрын
Mine worked twice then locked forever on last setting lol.
@kimchee94112
@kimchee94112 Жыл бұрын
I have the Craftsman torque wrench, garbage. It's well known as Crapsman. The only good ones are the Craftsman Professional line.
@OffRoadEndeavor
@OffRoadEndeavor Жыл бұрын
Decades ago it was a great long lasting tool brand. Not so much anymore. Since this video I have started using digi-torque adapters.
@jamesdean8193
@jamesdean8193 3 жыл бұрын
I got the 3/8s an 1/2 inch torque wrench like this one for 20$ each what I did was I took a tag off a 1/4inch craftsmen ratchet an I put it on the torque wrench’s an went threw the self checkout an they thanked me as I walked out the door like what a deal I got
@AAP0000
@AAP0000 3 жыл бұрын
lmao
@SolitaryMaverick
@SolitaryMaverick 3 жыл бұрын
Isn’t that stealing?
@AAP0000
@AAP0000 3 жыл бұрын
@@SolitaryMaverick Yes, and they would absolutely call the cops and charge you. I think what he did is funny, but not worth it to me. lol.
@BinleyClan
@BinleyClan 3 жыл бұрын
The more people that do this the higher the future price will be for this product. You're basically forcing the manufacturer to recoup it's loss by charging the consumer more. The loss is spread over the entire customer base. So...thanks for running the cost up for honest folks. Not impressed.
Fix Your Torque Wrench For Under $2
25:46
PhoRunner Channel (4Runner)
Рет қаралды 55 М.
You're Using a Torque Wrench Wrong: MythBusting 10 Do's & Dont's
20:25
Torque Test Channel
Рет қаралды 802 М.
REAL or FAKE? #beatbox #tiktok
01:03
BeatboxJCOP
Рет қаралды 18 МЛН
Enceinte et en Bazard: Les Chroniques du Nettoyage ! 🚽✨
00:21
Two More French
Рет қаралды 42 МЛН
It works #beatbox #tiktok
00:34
BeatboxJCOP
Рет қаралды 41 МЛН
US Made Craftsman In lb torque wrench
33:44
DaveS 777
Рет қаралды 6 М.
Setting a torque wrench. Easy!
6:57
Danny Johnson’s Garage
Рет қаралды 455 М.
O'Reilly 3/8" Torque Wrench Repair
8:18
chuck Carlley
Рет қаралды 29 М.
CALIBRATE YOUR TORQUE WRENCH IN UNDER 5 MINUTES (NO SPECIAL TOOLS REQUIRED!)
8:17
Vintage Engine Repairs
Рет қаралды 609 М.
How a torque wrench works
5:57
Deconstructed
Рет қаралды 2,7 МЛН
5 Problem Solving Tools
8:34
Essential Craftsman
Рет қаралды 1,1 МЛН
Product Review: Craftsman Micro Clicker Torque Wrench 3/8"
5:18
Kris Kasprzak
Рет қаралды 99 М.
REAL or FAKE? #beatbox #tiktok
01:03
BeatboxJCOP
Рет қаралды 18 МЛН