Crankshaft Position Sensor - Nissan Micra K12

Removing and replacing the crankshaft position sensor on a 2003 to 2010 Nissan Micra K12 1.0 litre petrol. Some of the most common symptoms of a bad crankshaft position sensor are: an illuminated check engine light, the engine won’t start or it stalls, the engine misfires or runs roughly and you might have reduced fuel economy. If you’re renewing the sensor, the part number is 237315M016. Thanks for watching. Please comment, like and subscribe !.
All of my uploaded material is protected under copyright law. None of my videos may be re-uploaded, reproduced or transmitted, in part or in full, in any form or by any means, without the written permission of the copyright holder.
© / screwsnutsandbolts 2022
Read important information below:
Disclaimer
Under no circumstances will Screwsnutsandbolts be responsible or liable in any way for any content, including but not limited to, any errors or omissions in the content, or for any loss or damage of any kind incurred as a result of any content communicated in this video, whether by Screwsnutsandbolts or a third party. In no event shall Screwsnutsandbolts be liable for any special, indirect or consequential damages or any damages whatsoever resulting from loss of use, data or profits arising out of or in connection with the availability, use or performance of any information communicated in this video. Due to factors beyond the control of Screwsnutsandbolts, it cannot guarantee against improper use or unauthorized modifications of this information. Screwsnutsandbolts assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. Screwsnutsandbolts recommends safe practices when performing any do it yourself repairs and or with tools seen or implied in this video. Due to factors beyond the control of Screwsnutsandbolts, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Screwsnutsandbolts.

[@screwsnutsandbolts]

Thanks for watching my video. If you found this or any of my other videos helpful, maybe you could consider supporting my channel by using the ‘♡ Thanks’ button below each of my videos. Your support would be greatly appreciated, thank you ! 👍 Screwsnutsandbolts

[@jean-marcknight8816]

I just id a P0335 default (using a basic obd and Torque app) I am not a mechanic and looking at other confusing videos, I didn’t feel like doing it until I found yours which is straightforward and clear as a mountain lake. I got me a new crankshaft sensor and did it. Well done sir 👍

[@screwsnutsandbolts]

You're very welcome, thanks for watching !

[@asadzaman5373]

Can you advise me where you bought the crankshaft sensor from?

[@jean-marcknight8816]

I ordered it in a shop but usually, I use autodoc

[@Sub-aru94]

@@jean-marcknight8816 original or some replacement?

[@Karim_Belgique]

Is this the vehicle speed sensor (VSS) on the transmission? I'm looking for it.

[@kaidi_jpg]

Hello, i have a missfire on cylinder 3, remove all spark plugs and ignition coil on this cylinder but i've still the same problem 😔

[@screwsnutsandbolts]

Does the engine have high mileage ?

[@kaidi_jpg]

@screwsnutsandbolts I have 181.000 kilometers. Is it a high mileage for 1.2 80hp engine, i dont know 🤷

[@screwsnutsandbolts]

No it's not too high. There could be other issues like a clogged or faulty fuel injector, a vacuum leak or even a compression issue with cylinder 3. It's hard to be sure

[@kaidi_jpg]

ok, so its could be everything 😬

[@harshitgupta885]

Can you help me with the part number of this green connector. Mine is worn out

[@screwsnutsandbolts]

It's very hard to find. This is the best I could could come up with: www.aliexpress.com/item/10000356135177.html

[@rajirahmto3964]

Please i have replaced the same part as in the video but the new part didnt work. The engine dont star. If i put the old one the engine start. The old part and the new one look from the outside exactly the same. I dont know what is the problem.

[@TorrenJohnson]

Hey can I ask you a few questions on your nissan. I have a nissan quest but I'm confused on something

[@SSATASS14]

Bonjour et merci pour vos vidéos elle mon bien aidé. Je voulais savoir si vous saviez ou se trouve le capteur pmh par hasard ? Merci et continuez 👍

[@screwsnutsandbolts]

What is pmh sensor ?

[@saifyhyper]

Hello, I have a 2006 Nissan Micra that only starts for few seconds and switche off again. I have changed plugs, coil packs, camshaft and crankshaft sensor but the problem is still there

[@saifyhyper]

It stays idle for few seconds and as soon as I touch the accelerator peddle it looses all the power and shuts off

[@screwsnutsandbolts]

It could be a faulty fuel pump, a clogged fuel or air filter among many other things. You'll probably need to take it to a garage to have the problem diagnosed

[@ssss-df5qz]

Immobiliser

[@producer7798]

Thanks 😘

[@screwsnutsandbolts]

You're welcome !

[@batuadjas4362]

My vehicle does not have a crankshaft sensor cable, how can I find it? Nissan Micra k12 2004 1.2

[@batuadjas4362]

Please help thank you

[@screwsnutsandbolts]

I don't know where it could be or why somebody would remove it, sorry

[@batuadjas4362]

@@screwsnutsandbolts There was a 3-pin crankshaft sensor in my vehicle, can I use a 2-pin crankshaft sensor instead?

[@screwsnutsandbolts]

I'm not 100% sure but I think you would need to use the same as the original for it to be recognised by the engine mangement system.

[@keemoak.]

My micra is cranking but not starting I checked the fuel pump its working fine i checked all fuses they are all fine then i removed the fuel injectors and tried to start it and it wont spray fuel and removed one coil to see if there is spark i didnt get any spark So can the crankshaft position sensor do it? Or is it the ecm?

[@screwsnutsandbolts]

It's one possibility. They're relatively cheap to buy so it might be worth replacing it first

[@wowabilaty]

Hey did you get to the bottom of the nonstart? Been trying to get some form of life out of mine for a couple of days now. Doesn't seem to be the crank sensor for me

[@AhNigqa]

Can A Bad Crankshaft Cause K12 Micra To Misfire ?

[@screwsnutsandbolts]

Yes it can be one of the possible reasons for an engine misfire

[@saddamhoussyen1900]

شكراً

[@screwsnutsandbolts]

You're welcome.

[@mushtaqqqq]

My car doesn’t start but start if I take off crank connector what does it mean? Where is the problem?

[@screwsnutsandbolts]

Crank connector ?

[@mushtaqqqq]

@@screwsnutsandbolts yes

[@screwsnutsandbolts]

I don't know what you mean by crank connector ?

[@mushtaqqqq]

@@screwsnutsandbolts ….I mean electrical plug which fits on sensor

[@screwsnutsandbolts]

Normally a car won't start if you disconnect the crankshaft sensor so that's unusual. I'm not sure what's happening there. You'll probably need to have a mechanic have a look at that.

[@burhan.guler1]

P0335 P0725 code ?