Creality K1 3D printer review

Get yours here: affiliate.geekbuying.com/gkba...
Discount code: NNNFRCK1UV
Warning, SOUND: I should have mentioned in my video that this printer with all the powerful fans is pretty loud. If you want to have a printer next to your bed working overnight, you better look for something a bit slower and less loud :)

[@RobinCernyMitSuffix]

it does cool down to prevent plastic from drooping out the nozzle while doing the bed leveling, as it would interfere with the loadcell bedleveling, which is why it touches the nozzle multiple times before, to push away any remaining plastic on the tip.

[@VRMinde]

I had this suspicion, but was not really sure. Thank you man!

[@klaidaslaurynaskalade9001]

Nice review:) And I get all the info what I was looking for about this printer. Now I can order one for me on Xmas:D. Thank you again.✌️

[@VRMinde]

Glad I could help! It is my favorite printer now

[@harryhalfmoon]

Eeeeyyy a fellow wingfoiler! Even more addictive than 3D printers!

[@VRMinde]

haha, yup, also kiter, windsurfer :) Where are you foiling?

[@harryhalfmoon]

On the lakes in the center of the Netherlands. Quite gusty usually, but very close to home. Going for a session in this morning. Stoked! Where are your spots located?@@VRMinde

[@VRMinde]

I am luckier with spots, from me 45-80mins drive brings me to either one sea or another :) Denmark. Always wind, waves and spots for whatever you want, flat, waves, etc. :) @@harryhalfmoon

[@ovs_cosplay]

In 7:00 it is happening because its part of your gcode. When you slice your file, there is a pre-code defining all these machine commands and add them to the gcode before the actual printing commands. Just make sure you disable it when slicing if you dont need it

[@VRMinde]

Nah mate, I have edited the start gcode and the printer does not care about it. Looks like it is in the firmware

[@I000I]

Did you print with real nylon, or it was just some mixes like "Easy Nylon"? On my open chamber printer i forced to use special glue for the nylon, otherwise it just peal off my PEI bed even on tiny prints like washers.

[@VRMinde]

I think it is the Overture brand nylon, not sure how “easy” or not it is :D I have to admit I am new to nylon, it is the first one I tried

[@3DPrintingForFun]

Hello! Can you share your settings profile in Creality Print? I also own a K1 printer, but I've been struggling with its settings in the slicer for a week now. Thanks in advance!

[@VRMinde]

Hi mate, I can check later, but I have spent not a lot of time on creality cloud. I could better share Orca slicer settings?

[@3DPrintingForFun]

Orca Slicer,ok)can you share the settings for this slicer?it might help me)Thx)

[@VRMinde]

we.tl/t-V5oxfYPtEc Ottherwise just start with stock Orca K1 profile and push speed+accel up until it stops being good :D @@3DPrintingForFun

[@laughingman4134]

Its doing a nozzle wipe lol. Heat up to melt then cools enough that it can pull any stuck filiment to prevent build up.

[@VRMinde]

Thanks bro, you live and you learn :)

[@f3lan]

Did you buy the camera as an add on or did it come with it?

[@VRMinde]

It came with it, but the camera and a roll of high speed filament came like a month latet than the printer itself

[@algisberziunas]

ziuriu kad akcentas kaip pas Minde :)))

[@VRMinde]

😅 koks jau yra toks :)

[@djgraffiti5627]

My God man your ringing is terrible. But you probably printed fast so... Forgiven

[@VRMinde]

20k acceleration and 300-400mm/s 🙄

[@Untiocansado]

did you calibrate the input shaping?

[@VRMinde]

@@Untiocansado It calibrates itself when you do the initial full calibration and judging by the movements the printhead does - before every print as well. Are you talking about any additional calibration?

[@mortegutt]

​@@VRMindeyou need to root printer and change printer.cfg to do input shaping on y-axis as well. Creality only does x-axis and use the same value for y. This is a lazy and terrible decision by creality.

[@VRMinde]

@@morteguttthanks man. I did not know that. I am not sure I am gonna do it. It is my favorite "go-to" printer at the moment and I do not want to mess it up :D