Music Reactive LED Strip

[@sergiohenriquedasilvaleal1462]

Boa noite, O Sr , é sensacional , quanta idéia brilhante, meus parabéns a o Sr !

[@levistrnad2965]

I see a few other comments like this, but can you tell me how the MOSFET is used and can I use a transistor or smaller mosfet

[@edilsonjaramillo8754]

Amigo ese mismo circuito se puede usar sin micrófono? Y con un tip31c

[@ashiqhussainhussain3932]

very good way for help the people good job and good hobies realy sir you are great

[@rajatghosh1158]

From which video u learned to make that that ATX power supply ? From Greatscott! Or yourself

[@JoseSilveira-newhandleforYT]

Nice simple idea. I would add a low-pass filter after the mike, to get mainly the bass beat - increases the effect.

[@Creativecreator]

Great 👌

[@dhiea289]

How to add and how to make a low pass filter??

[@JoseSilveira-newhandleforYT]

@@dhiea289 Have a look at this: prntscr.com/mwf43n

[@JoseSilveira-newhandleforYT]

You may try something like this, but there may be not enough gain: prntscr.com/mwfluy

[@dhiea289]

@@JoseSilveira-newhandleforYT i have a problem with the brigthness of my LeD strip... I cannot utelize the full brightness because if i turn the knob it will lit bright but it will not blink to the bass at all

[@shaileshj2229]

Can I use mic used in earphone instead of buying new condenser microphone?...does it handle that much power 12v dc? What do you think?

[@helder1911]

Great dude! How Can i do to have the Max level of sensibility in Mic?

[@yeskolik7094]

Can we make it with mushroom LED ?

[@sorenzx1923]

Omg what soldering iron are you using? Mine is such a bloody headache to use

[@Creativecreator]

Chinese cheap 60w iron

[@rajatghosh1158]

@@Creativecreator I use soldron si25a model 25watt soldering iron

[@InventorChannel2023]

Nice video Good job ❤❤

[@rirashed6760]

You are awesome! Which software did you use build circuit diagram?

[@Creativecreator]

thank you so much !! I use easyeda

[@boblorejas9551]

can i use B50k potentiometer Sir?

[@Хочубытьдобрым]

Радость эпилептиков!

[@liveelectronicmusiciansofm7438]

Hey brother. Is it possible to replace the condenser mic with a jack input? So I can plug an audio source straight into it!

[@Creativecreator]

Yes possible but I have not tested yet buddy. And one more thing why you should connect you expensive phone with your audio jack. If you do anything wrong then the headphone jack will not work any more. So, besure what you are doing. Cheers! 😉

[@xvd4754]

Can i use IRF 3205 or IRF740 instead of IRFZ44N ? New subscriber here 😅

[@Creativecreator]

You can use any n channel MOSFET.

[@xvd4754]

@@Creativecreator ty sir i already watch ur prev video your videos are cool 😄

[@Creativecreator]

Thank you so much for your support ❤️

[@carloseduardopineda2939]

It works with a jack conector?

[@ahmetcanyalcn1673]

could you explain it. i want to do it with a jack connector.

[@6-i-9]

What transitions are those? are they from a pack? which editing software? Please tell me

[@DeffoNotV2]

I've hooked this up to a 9v battery but no joy, the LED turns on but doesn't react to the music, does it have to be 12v?

[@HRTechnicalShorts]

Very nice

[@muruhappanchidambaram9489]

How does this work

[@mybluebelly]

Pretty cool man :)

[@haneybebeng7631]

How can i make it not so sensitive with the sound?

[@Creativecreator]

Use arduino nano it will be more sensitive 😀

[@Жека-ж2п]

can you make the engine spin to the music? Thanks.12v

[@bablubhoi2032]

Ae 5 v me chalega kia

[@Creativecreator]

Then you need to change the resistors

[@Rider112]

Interesting :) but I will try to make a small modification of your system - I will see if it will work ;)

[@Creativecreator]

Let us know after your modification...

[@Rider112]

Ok :)

[@AmanVishwakarma-db9zp]

Rider 112 9

[@hasangaming4489]

nice thank you

[@ElectricCreative]

Nice idea's Bro

[@Creativecreator]

Thank you so much 😀

[@SomiiProduction]

bro is ko speaker ksy sath kasy conect kry gay. mic ki jga?

[@sudarshankothawale6860]

I've done the circuit as shown in the video but it's not blinking please help .

[@vanchatv]

I'm already a subscriber

[@Creativecreator]

Thanks once again 😃

[@kayfatotkinoha8789]

thanks .good job

[@Creativecreator]

Welcome

[@DiyElectronic]

Awesome... 👏

[@Creativecreator]

Thank you

[@prelectricianelectronics4663]

#PRElectrician & Electronic My Channel Subscribe

[@prelectricianelectronics4663]

#PRElectrician & Electronic My Channel Subscribe

[@FlowwUP]

this loud fuckin NCS music all the time in the baground drives me crazy

[@VIJAY-co4sh]

nice bro explain the working function of MOSFET

[@subzeroelectronics3022]

The MOSFET (Metal Oxide Semiconductor Field Effect Transistor) is a semiconductor device widely used for switching and amplifying electronic signals. It has three terminals, source, gate, and drain. If current flows from the gate to the drain, the MOSFET lets a larger current flow from the source to the drain. If the gate current is increased, the drain current will follow linearly. This is called the linear range. The linear range lets the drain current increase until it has reached equilibrium with the source current. Once this happens, increasing the gate current will not affect the drain current. This is called the saturation range. Another way to think of it is as a tap. The source is where the water supply is, the gate is the handle, and the drain is where the water comes out. You can turn the handle (gate) up, but at a certain point it doesn’t result in a change in output (saturation range). Hope that cleared it up for you.

[@dhimande2646]

Congratulations very very thanks

[@ikhvanardana4961]

That's great sir! 👍

[@Creativecreator]

Welcome

[@cls3093]

very good

[@Creativecreator]

Thank you so much 😀

[@thewrench513]

printer scanner light to bahar kaise jalaya jay.. reply must

[@leomarbunledaccesories7442]

Nice Sir n thanks for your video

[@brainventor9031]

Great

[@edifierbass7821]

You stick it directly to the speaker, I thought you will put it a good distance to test the sensitivity

[@Creativecreator]

you can keep it far but my condenser mic is small so I fixed it in front of my phone speaker with tape

[@edifierbass7821]

@@Creativecreator Oh ok i got it the sound from the celfon is not enough to drive the mic , hope yu make another video using your home stereo it would be great and thanks

[@Creativecreator]

Exectly ☺️

[@cuda426hemi]

I wonder - instead of the condenser mic - could you tap the headphone jack out to the Pot and then Mosfet? 🎸

[@Creativecreator]

Thought this before but if I use 3.5mm jack then you will not able to hear music because of audio jack

[@cuda426hemi]

@@Creativecreator Yeah, I was hoping maybe phones could be like a Mac/Receiver where you could have either or both or none "on". Cheers!

[@Creativecreator]

Don't forget to subscribe buddy 🙂

[@cuda426hemi]

@@Creativecreator Already was ! 🎼

[@Creativecreator]

Thank you so much for joining Creative Creator community :)

[@subramanyabhat23]

Is there any replacement for 10K potentiometer

[@Creativecreator]

You can use any Low Range Resistor below 10k instead of 10kpot but in that case you will get a fixed depth of blinking.

[@dhiea289]

Can i add capacitor in the line with the mic to boost the signal?? So that the. Brightness of the led is in full wave??

[@ЭдуардСуровый-э2и]

Молодец

[@christiancardin6542]

Will this work w 6v rgb led strip?

[@Creativecreator]

No i guess

[@Creativecreator]

Hope You Enjoy :) Learn More: circuitbest.com/led-dimmer-circuit-with-555-timer/

[@constantinbaiculescu5146]

🌞

[@SomiiProduction]

direct speaker kay sath kasy ho ga. mic ki jga pr

[@sinaebrahimzadeh7700]

I made with lm358 i don't it works or not

[@SomiiProduction]

bro kia potentiometer kay bagar ya kam kry ga?

[@ManojSingh-dy7qt]

bro it didnt work

[@pioioloco]

parabens pelo video amigo, show :-)

[@Creativecreator]

thanks

[@elijahponce7944]

@@Creativecreator where can I find the most or irfz44n

[@Creativecreator]

@@elijahponce7944 from local shop or AliExpress Banggood or Amazon 😁

[@elijahponce7944]

@@Creativecreator thanks so much and I love your vids it keeps my ability up. But thanks

[@todorkotov2622]

what is the microphone

[@Creativecreator]

Takes sound from Environment

[@priyanshubaluni2801]

I have used A10K Potentiometer and my led is not glowing properly. Thus buying B10k Potentiometer will it resolve this problem?

[@electriclocha]

good job bro

[@rusername]

Awesome😊

[@sheenajoseph9047]

Shall we use a led light

[@Creativecreator]

Yes

[@khelahoberifles832]

What will happen if I use 4v led strip and replace potentiometer by1k resistance but rest of the things unchanged

[@Creativecreator]

1k pot is ok but you have to make the 4v led strip running at 12V

[@mariosergiogroetares9343]

Valeu! Grato! Muito bom!

[@arlindosilva61]

Grato

[@wagneroliveira3629]

bom dia gostaria de saber como eu ligo ledes em 24v

[@hasangaming4489]

like do you can give name music please in the phone

[@dreamsquad6161]

LiQWYD - Explore

[@avildsilva6859]

Guys can u plz l tell me that it's working properly wat ??

[@xdigarumeghas1673]

Nice but at the first try it was not working

[@electroniquepassion]

Thank

[@aserden2461]

Best of the best! )

[@Creativecreator]

Thank you so much 😀

[@brendancull8316]

Your soldering leaves a lot to be desired!

[@juliodjcontrolvinyl]

Es mentira !eso no funciona nada 😢

[@daliborkocian2826]

Jiné zapojení a jiné schéma....

[@MrLibbyloulou]

Was that a 240 power supply?

[@furkan_karagulle]

Have u made with tip31 transistor muzic bass

[@Creativecreator]

I will try to make... Don't forget to subscribe buddy 🙂 This really motivates me a lot. !!

[@furkan_karagulle]

@@Creativecreator sure i subsrcribe your channel and thanks sorry for my bad english 😁😁

[@Creativecreator]

No worries buddy!!! Welcome to Creative Creator community 😀

[@furkan_karagulle]

@@Creativecreator 😄😄😄😄 can u cooler of fans for mobile phone with holder for play pubg mobile

[@Creativecreator]

Thanks for the suggestion 🤗

[@souadsahli945]

Nice

[@Creativecreator]

Thank you so much 😀 Please subscribe and be a part of Creative Creator community..

[@alssahoky2931]

good

[@Creativecreator]

thanks...

[@rajurathor6939]

Led bahut law glow ho Rahi h use kese badaya ja Sakta h brightness kese badegi plzz reply

[@Creativecreator]

rotate the pot and take closer the condenser mic to the sound system. hope this will work :)

[@rajurathor6939]

@@Creativecreator pot kya sir

[@Creativecreator]

10k Potentiometer

[@rajurathor6939]

@@Creativecreator sir wo to check kr Liya kuch extra lga ke ya koi component change krke bad Sakti h

[@alexismerqury5781]

Перестаньте крутить детали туда - сюда. Время отнимаете.

[@maxnikolaev6040]

Обезьяна с гранатой

[@vanchatv]

Cool) Like)

[@Creativecreator]

Thank you so much!! Please subscribe and be a part of Creative Creator community 😀

[@vanchatv]

I'm already a subscriber

[@francisseries126]

Thats a cool idea, but... the way u solder it is terrible ... that hurts me bro😂 use a breadboard or a pcb

[@Creativecreator]

Sorry for that

[@interestingglobus8060]

creative

[@maxmaxxel1583]

Music LED RGB please

[@Creativecreator]

I will wait for the video

[@maxmaxxel1583]

That my request

[@arttechvision]

Amazing...

[@Creativecreator]

Thank you so much 😀

[@AnitaRajeevSingh]

Bhai Main yeh circuit Bana lekin work nahin kar raha

[@Creativecreator]

Kuch galti kya hoga vii maine pura test karke upload kya video

[@АлександрКалинин-е4ю]

👍👍👍

[@BondanHeru]

My mic working on airflow, not volume beat

[@khelahoberifles832]

Sir say me if u had changed any part

[@20012003mama]

Put the strip at Audio output Form Stereo System.. 1000t besser lol...

[@Creativecreator]

🔥🔥🔥

[@edcarlaferreira2803]

SanDambu King .

[@IDUKKI._VLOGZ._]

Friends please subscribe my channel too link kzbin.info/www/bejne/nXKnc3aqd7Vmfbs

[@BondanHeru]

Burning your amp

[@sagorbasak7532]

Dada apki light Chali gayy

[@funk23]

Muito escuro a gravação

[@shadowwalkerpiczon4414]

It's a simple

[@babu4345]

Why the music!!??

[@dawsonrajput5050]

music reactive circuit can be made in 4 manners : kzbin.info/www/bejne/Y3Kci3qNos94fs0

[@drisdrz5194]

نرجوا ما يفيد اكثر.

[@tomaszt.zuchniewicz7106]

Pomysł ciekawy ale sam film, z racji "efektów" , nie nadaje się do oglądania.

[@Creativecreator]

postaram się uczynić go bardziej profesjonalnym ciągle się uczę !!!

[@RandomFun111]

Need improvements

[@Школьнаяжизнь-р8и]

Honor

[@ritaisabel8665]

show 1.000

[@Big_BOSSSSSSS]

Нахер я это смотрел???

[@robertoroberto1122]

Roberto

[@marcomanta2830]

😐

[@vikrambarai6299]

Light nahi tha

[@agatamoura5591]

Like !

[@Techvalte]

Very creative I also have a tech channel do check it out

[@chetananam475]

Link for the channel is available?

[@Techvalte]

@@chetananam475 here is the linkkzbin.info/door/vPOmPjf8sFSrJX1KqUCFuA

[@DmitriyNik]

Сложно это все. Проще припаять провода к динамику,чем больше громкость тем больше напряжение. Ну конечно же не к мобильнику припаять.

[@constantinbaiculescu5146]

Like 😘

[@ВалераБеннер]

Это не вариант на транзисторах

[@resulmehmetoglu7519]

Не впечатлил.

[@sergioarrieta9671]

Malo malo

[@abderrazak2039]

A