In this video I am going to show you how to Install Chamberlain Garage Door Opener )Model B6753T). Let me know what you think. 🙂 And DON’T FORGET TO WATCH My How to Lubricate your Garage Door - DIY Video: kzbin.info/www/bejne/j3WanaBrh9uMjJY Best wishes Vadim
@hadikaykouni54462 жыл бұрын
Hi Is it 220 volts?
@RicardoZea7 ай бұрын
HUGE, HUGE Thanks for making this video, so frigging helpful! For those first-time installers like me, here are a few things to note that the video doesn't mention: 1. Hopefully not for you, but the programming can be a ROYAL PIA. My error was 4-6 (4 up - 6 down in the adjustment arrows on the unit). If your sensors are aligned, meaning the one is solid amber and the other one is solid green, that doesn't mean they're OK. Go back, unalign them to where the LED starts blinking, and realign them again (both LEDs are solid). It took me several hours and a lot of frustration to figure this one out. 2. The garage door opener is not going to automatically work right after plugged in, as the author shows at the end of the video. You have to set your traveling distances to the door. This video from Chamberlain Support was actually very helpful too for that (amongst other things): kzbin.info/www/bejne/bYfaaKh6msiNh7M&ab_channel=ChamberlainSupport 3. Unless they are in bad condition, if you can use the wall and garage door supports from your old unit, use them. 4. The Built app is somewhat helpful, but a PIA to use on your phone. Be patient if you plan to use it :p 5. Unlike some old garage door opener units, the hanging brackets that attach to the sides of the unit and are attached to the ceiling, may need to be cut to the edge. In some old garage door openers, the ceiling brackets “run down” the sides. That's because the mounting brackets on the unit are placed right at the edge of the body. With this model, the mounting brackets are further in from the edge. See what I mean here: kzbin.info/www/bejne/Z3rYo3una9J2ZqM -- and here: kzbin.info/www/bejne/bYfaaKh6msiNh7M 6. The remotes come pre-programmed (phew!). 7. To release the spring as explained here kzbin.info/www/bejne/Z3rYo3una9J2ZqM, you will need an adjustable wrench and a flat-head screwdriver, here's a video showing how to do it: kzbin.info/www/bejne/bYfaaKh6msiNh7M 8. To lift the tab in the front rail, I found it easier to stick a screwdriver through the small hole and lift. Then with a pair of angle nose pliers, I got it straight. 9. I thought the sprocket in the unit (where the belt turns around) had to be lubricated, but no, it comes pre-lubricated (the author does mention this, lol) so you don't have to get messy :p 10. Here's a link to the manual: cgi.widen.net/view/pdf/4ibaxxmkpa/114-5548-000.pdf Enjoy your installation! =D
@Ryan-ls2wo4 ай бұрын
Thanks to you and the maker of this video
@chipdouglas28194 ай бұрын
Super helpful information, thank you
@demonx3610 Жыл бұрын
How do you release the spring??
@therustyjohnson3 ай бұрын
I'm always so skeptical when it comes to these how to videos. You did a great job on this one. It's refreshing to see one with good audio, good video, at a good pace with clear details.
@CorkyWineАй бұрын
Beautiful job, especially that you protected the motor head from getting scratched. Nice job.
@wsapp98235 ай бұрын
I watched this video and LMAO about your make shift support stack!!! Thanks pal, I needed that!… you have to do what you have to do, right!!!
@CreativeProcessDIY3 ай бұрын
yep,)))
@CorkyWineАй бұрын
I just a tall ladder, but then I have a few ladder, hey what ever works is cool.
@SnoTs2 жыл бұрын
This door opener is on clearance now and your video gave me the confidence to go ahead and replace my loud chain open with this thanks for the video.
@CreativeProcessDIY2 жыл бұрын
Glad I could help!
@EmailingEd11 ай бұрын
Hello and thank you for your help, the video was very helpful and detailed. I had to learn how to program the open and close limiter before the garage door would work but you basically helped me 90% of the way. Thank you again!
@mrnoedahl Жыл бұрын
I don’t understand what was being released when you said, “before release and after release” when installing the belt. Please help me and explain it better.
@neilleo97447 ай бұрын
it's that little spring. It's 1 inch before release. It becomes 1.1/4 inch AFTER you released it.
@onfaithalone42537 ай бұрын
I don’t get it wither
@Marius856 ай бұрын
How do you release it? Thats the problem.
@angellepire94125 ай бұрын
In the instructions it tells you how to release it with a screwdriver and wrench, but mine is way more than 1 1/4 inch. I’m having a very hard time “tightening” it to the correct size once it’s released.
@jamesh4603 ай бұрын
You gotta read the actual instructions for this step… this video isn’t a step by step installation… google the instructions if you lost them
@a.nonamouse2986 Жыл бұрын
So helpful. Excellent! Appreciated the detailed instructions and loved the innovative support tower. Thank you very much. You have given me the confidence to attempt this myself.
@CreativeProcessDIY Жыл бұрын
I am glad it helped! Good luck and thank you for watching!
@MQT- Жыл бұрын
Thank you for the thorough installation video ❤
@CreativeProcessDIY Жыл бұрын
thank you for watching!
@todddiek861 Жыл бұрын
Very well done! One of the best I’ve seen. Very detail oriented. I especially liked the non-overwhelmingly loud background music. Only thing better would have been no music. 😀
@Ironwokdude Жыл бұрын
I agreed lol, but thanks bro.
@joefalkner23686 ай бұрын
This is an excellent video. It might be the best DIY video I’ve ever seen. 😊
@CreativeProcessDIY6 ай бұрын
thanks for watching
@hayeshine Жыл бұрын
Awesome video. Thank you for the in depth installation. I look forward to rewatching it when mine gets delivered!
@CreativeProcessDIY Жыл бұрын
Thank you so much for watching!
@ThinkAboutTheWow2 ай бұрын
Very nicely done detailed video. you just raised my confidence for self-install. thank you.
@CreativeProcessDIYАй бұрын
that's great! thanks for watching!
@charliednewell Жыл бұрын
this was so helpful. very patient. very clear. thanks.
@CreativeProcessDIY Жыл бұрын
Thanks for watching!
@tomandbunny Жыл бұрын
Just bought one and thank you for your video, very informative.
@CreativeProcessDIY Жыл бұрын
Thank you for watching!
@علينقي-ش1ي3 ай бұрын
Thank you so much for this amazing video ♥️
@CreativeProcessDIY3 ай бұрын
thank you for watching!
@ScottyOutdoorAdventures3 жыл бұрын
My directions say DO NOT PUT THE RAIL LEVEL it should actually slope downward away from the door. Still, A great video. Thanks!
@CreativeProcessDIY3 жыл бұрын
Thanks!
@justsayin36002 жыл бұрын
I'm about to install this very model. I'm glad I saw this because I didn't read the directions yet but only watch Chamberlain's video on how to install a similar model.
@mandoa.9052 Жыл бұрын
I did the same thing you did installing the opener, but for some reason when I press the button to close it, lights just blink . What do you think I’m doing wrong?
@killaseason123456711 ай бұрын
I’m having the same issue if you find a fix could you let me know please and thank you
@jorgeprieto22282 жыл бұрын
Thank you for taking the time to explain everything in detail, the video was a huge help.
@CreativeProcessDIY2 жыл бұрын
Glad it was helpful!
@salinsarin111 ай бұрын
Super nice explanation.. Thanks
@CreativeProcessDIY11 ай бұрын
You are welcome
@rivec333 ай бұрын
That’s the most genius support for the motor I’ve ever seen.
@CreativeProcessDIYАй бұрын
thanks for watching!
@RIchardDavidson00712 күн бұрын
Excellent video.
@RDSZ4 ай бұрын
Thanks for the diy instructions
@CreativeProcessDIY4 ай бұрын
thanks for watching!
@tomdfire97 Жыл бұрын
Great video! Thank you for making it.
@CreativeProcessDIY Жыл бұрын
Thank you for watching!
@alanckaye2 жыл бұрын
Not understanding what you mean by spring and release, not released. Thank you this video is a great help.
@CreativeProcessDIY2 жыл бұрын
Glad it was helpful!
@carymark7102 жыл бұрын
Great video! I have already installed one of these in my garage. When you follow the instructions for the height of the rail and the opener the rail will NOT be level. The instructions say that the rail will NOT be level also. The rail will run downhill slightly toward the opener.
@CreativeProcessDIY Жыл бұрын
Thanks for watching!
@jakemccabe8217 Жыл бұрын
Ur awesome man thanks so much for this tutorial!!!
@CreativeProcessDIY Жыл бұрын
Thank you!
@damson28092 жыл бұрын
Looks like a lot of work. Respect
@CreativeProcessDIY2 жыл бұрын
Thanks
@paulonunesfernandes3 ай бұрын
you are the best. thanks
@CreativeProcessDIY3 ай бұрын
Thank you for watching!
@loganopfer5326 Жыл бұрын
Awesome video
@CreativeProcessDIY Жыл бұрын
Glad it helped!
@dobleu13Ай бұрын
Is it apple home kit compatible ?
@aeadler19852 жыл бұрын
I install these EVERY day.. You do it the hard way bro. It’s so much easier and quicker.
@CreativeProcessDIY2 жыл бұрын
This is DIY installation...
@AntLive29 Жыл бұрын
what is the easier and quicker way?
@Johnnyandkik10 күн бұрын
Please share your video
@mq28252 ай бұрын
I installed this opener today watching this video, problem I’m having is when the door opens the rod starts to bend and I’m scared it will snap. It hasn’t snapped but u can see the force. Any suggestions?
@RealMacoy2 жыл бұрын
Congrats ..thank u for posting this video..So easy to follow. I will install mine anytime soon.More power to you.
@CreativeProcessDIY2 жыл бұрын
Thanks a lot for support!
@sphchurch11 ай бұрын
have a unique situation, I know everyone’s is unique. But really this one is. The front of my garage sticks out 2 feet from the house. On top of that inside the garage there is a support from the house that goes through the garage that will not allow the door lifting chain rail puller to go all the way to the front above the door. Any ideas. Would like to try and do this myself. I believe would need a bar about 2 feet long from the door to the motor drive chain rail. Any ideas?
@STV-H4H2 жыл бұрын
I installed this same product last night. The essential install was simple. The actual door lift and lower process went fine. The safety sensors set up Much simpler than other doors I’ve worked with. The problem was it wouldn’t work with the main wall switch no matter what. Even touching the wires to close the circuit. 😢 Never figured out the problem. Customer got pissed off and fired me. Paid me 1/2 my fee at least. I’m assuming the devise was defective possibly. I was hoping this video included the trim and programming details to possibly see if I missed something
@STV-H4H2 жыл бұрын
@InThisTogether the funny part was his previous garage door opener worked fine, he just wanted the WiFi and camera application this silly new devise had. So IF he can get it up and running, I guess the camera will assure him his car isn’t still in the garage I guess. Almost as absurd as having an app for the fridge to let you know whatever it’s supposed to inform the owners of while they are at work or shopping. As an appliance repairman, I know this is truly a desirable feature because they break and someone has to get paid to fix them. Personally I have zero interest in such repairs, but I. Sure LG and Samsung are ecstatic that new appliances cost as much to repair as buying a replacement instead of getting them repaired. The down side is that while I know how to repair my own things, I just hoped that buying higher quality meant I did need to for perhaps longer than warranties etc.
@AmericanJustice22022 Жыл бұрын
Great Video, Im curious if there is a beep function? I saw other videos where the garage opener had a beeping noise when opening and closing!
@CreativeProcessDIY Жыл бұрын
don't know about that. try to contact chamberlain customer service for that
@JamezGrimm4 ай бұрын
Honestly I’ve been trying to release the spring for over an our now 😂
@AsimUllahOnline2 жыл бұрын
How to program keypad outside of garage with this. Which wire goes where for that. ?
@CreativeProcessDIY2 жыл бұрын
I can't answer this question.
@charliekilo32 жыл бұрын
The outside keypad is wireless.
@williamkirby91918 ай бұрын
When you make an instructional video, the orientation of the parts being assembled would be a great step to add in the future. Just saying.
@AsimUllahOnline2 жыл бұрын
Can the keypad outside of garage from liftmaster be use with this unit ? Does any wire need to go in the unit for it and if yes . Where ? Where the red white go or somewhere else ?
@CreativeProcessDIY2 жыл бұрын
I can't answer that question.
@christucker81322 жыл бұрын
yep same company.
@ZebMoney3135 ай бұрын
Where did you get the instructions from
@CreativeProcessDIY3 ай бұрын
It came with it
@KhanhNguyen-uw2wz2 жыл бұрын
You can use remote program and very easy too.
@CreativeProcessDIY Жыл бұрын
thanks for watching!
@constantinstirbu61822 жыл бұрын
Very nice presentation I will purchase one in follow the steps Thanks
@CreativeProcessDIY2 жыл бұрын
Glad it was helpful!
@heroknaderi3 жыл бұрын
Wow very cool Opener i like it. Good job. And i saw the Attic access like you said was in the way i beleive the opener could have beed installed in the center then add a seconf access later on. But syill this opener rocks. I enjoyed watching the installationn.
@CreativeProcessDIY3 жыл бұрын
Thanks for watching!
@gradientgamer54802 жыл бұрын
is it possible to swap the square rail with a liftmaster T-rail
@CreativeProcessDIY2 жыл бұрын
not sure
@gradientgamer54802 жыл бұрын
@InThisTogether you can. you just gotta change the location of the stopper bolt so it doesnt obstruct the pathway doing so clears the area
@carymark7102 жыл бұрын
One thing I will mention with installing this garage door opener is NOT to adjust the UP door position with the adjustment buttons higher than what the garage door normally goes when you put the door up manually with your hands since it can make the steel braided cable come off the drum (pulley) Mine had a couple of revolutions of cable come off the drum while the door was in the up position and I read that is what can cause that. I was able to put it back on though just turning the steel rod with my bare hands while the door was in the up position since it appeared to have very little tension left in the up position. Seems to be ok for now.......
@johnnnybravo5856 ай бұрын
What was total length after install?
@losgatoskao2 жыл бұрын
I've everything installed and the LED (green and amber) on the Protector Sensors are solid. When I pressed the button on the wall or the remote control to optn the garage, the Chambberlain's LED blinked twice and didn't do anything. Any idea?
@cindynguyen9432 жыл бұрын
I have the same problem, help anybody? Thanks.
@trongcaylungtung66752 жыл бұрын
@InThisTogether I had to call tech support and they guided me through the process. They were very helpful
@CreativeProcessDIY2 жыл бұрын
Try to contact customer service
@DHP953072 жыл бұрын
Thank you and for being so detailed..
@CreativeProcessDIY2 жыл бұрын
Glad it was helpful!
@jagjeetsingh15195 ай бұрын
Hi I followed all ur instructions but one of sensor is orange and one is green and door is not getting opened
@manuelcastillo5252 жыл бұрын
8:29 the best part of the video...
@CreativeProcessDIY2 жыл бұрын
))))
@olikciuicova2 жыл бұрын
Great video ! Thanks 😊
@CreativeProcessDIY2 жыл бұрын
Glad it helped!
@DaCelestial11 ай бұрын
I know is this a bit late, but the Garage door is not suppose to be level according to instructions.. or does it not matter ..
@charliekilo3 Жыл бұрын
You forgot to install the cover over the belt drive gear on the power head. Thanks for the educational video.
@CreativeProcessDIY Жыл бұрын
thanks for watching!
@729cvo5 Жыл бұрын
Mine had missing part out of the box
@CreativeProcessDIY Жыл бұрын
contact Chamberlain customer service. They should help you
@LorenDarsen2 жыл бұрын
My favorite master 🙌 👌❤♥ 👌❤♥
@CreativeProcessDIY2 жыл бұрын
thanks!
@sakalabolsita63163 жыл бұрын
What do u mean for the coil before and after release? @ 5:20
@CreativeProcessDIY3 жыл бұрын
1. By hand, thread the spring trolley nut on the threaded shaft until it is finger tight against the trolley. Do not use any tools. Remove the screwdriver. 2. Insert a flathead screwdriver tip into one of the nut ring slots and brace it firmly against the trolley. 3. Tighten the spring trolley with an adjustable wrench or a 7/16″ open end wrench about a quarter turn until until the spring releases and snaps the nut ring against the trolley. This sets the spring optimum belt tension.
@sakalabolsita63163 жыл бұрын
@@CreativeProcessDIY Thank you brotha…🤙🏼
@ldburgie2 жыл бұрын
About how long does installation take?
@CreativeProcessDIY2 жыл бұрын
3-4 hours
@nghialuu71393 жыл бұрын
thank you!
@CreativeProcessDIY3 жыл бұрын
You're welcome!
@YumYumNP2 жыл бұрын
Thanks!! The video is great I just installed mine. Couldn't have been able to do without the video
@CreativeProcessDIY2 жыл бұрын
Glad it helped
@CorkyWineАй бұрын
Great vid, nice job, and BTW u are cute,
@I-sed-no3 жыл бұрын
Excellent video! Thank you
@CreativeProcessDIY3 жыл бұрын
Glad it helped!
@pby7675 Жыл бұрын
No programming required??
@KhanhNguyen-uw2wz2 жыл бұрын
Chamberlain B4613t is very easy to install.
@KhanhNguyen-uw2wz2 жыл бұрын
Nice 👍
@CreativeProcessDIY2 жыл бұрын
Thanks for watching!
@KhanhNguyen-uw2wz2 жыл бұрын
@@CreativeProcessDIY you’re welcome 😊
@manintoynenam2 жыл бұрын
How long is the rail? 8’ or 10’
@CreativeProcessDIY2 жыл бұрын
I do not know. Read chamberlain description of the product. It should provide you such details.
@stevevlahos12 жыл бұрын
Thank you. I will get the same model.
@CreativeProcessDIY2 жыл бұрын
Glad you enjoy it! Consider subscribing to my channel. Thanks
@GDOs3 жыл бұрын
the place you put your opener is going to pull out of the door because there is no support behind that bracket, you can tell because there’s no hinges below it. i suggest moving it back before you get problems
@XellosMetallium2 жыл бұрын
i wish they include hanger kit.
@CreativeProcessDIY2 жыл бұрын
they do include it. I just decided to use the old one because the metal is thicker
@adriancleveland4838Ай бұрын
Wow great video and I followed everything exactly…. And then… nope doesn’t work, the app says sensors misaligned, took me around 90 minutes to assemble and install everything, and 4 hours later the app says I’m still misaligned, even removed the sensors and put them close together, but nope, nothing, going to be headed right back to the Home Depot returns desk in the morning with this pile of junk, I’ll exchange for a nice handle that you just pull up and down, what was I thinking.
@RDSZ4 ай бұрын
You didn’t mention about the app to open door with your smartphone.
@LorenDarsen3 жыл бұрын
Klass....super 👌 😄 🏈 👌
@CreativeProcessDIY3 жыл бұрын
thanks
@impact69082 жыл бұрын
Did not mention anything about the CAMERA. What is the camera for?
@SnoTs2 жыл бұрын
It's just like a doorbell camera. When the door is used it takes video. This way if the door is opened and you aren't the one opening it you can see who/what opened it.
@CreativeProcessDIY2 жыл бұрын
Watch my last video. Thanks
@GPSniper1 Жыл бұрын
thanks
@CreativeProcessDIY Жыл бұрын
thanks for watching!
@alfonsoferraro67742 жыл бұрын
Mine only came with 3 wear pads...🙄
@cama81z2 ай бұрын
you didnt show how to program the wireless controllers
@charliec94053 жыл бұрын
Great video, love the complete details! Was the rail the same length as the one you replaced?
@CreativeProcessDIY3 жыл бұрын
Thanks! Yes, it was
@jasonrodriguez6373 жыл бұрын
@@CreativeProcessDIY I bought this garage door opener and tried to install it but realized I had an 8 foot garage door will it not work?
@Dr-wheel-barrow-opperator2 жыл бұрын
Spasibo!
@CreativeProcessDIY2 жыл бұрын
Thanks for watching!
@ZebMoney3135 ай бұрын
It doesn't come with installation instructions. Just instructions on how to program the wifi and bells and whistles. But as fsr as installing youre on your own
@CreativeProcessDIY3 ай бұрын
try to get it from Home Depot website, under the product they will have the assembly instructions file
@CorkyWineАй бұрын
OMG what id- iot builder put the attic hatch in that bad position.