The BEST way to get the MOST useful HORSEPOWER out of your ATV or Side by Side!!

[@goodboyringo9716]

Rap a tie down strap around the primary and hold it from turning to torque it.

[@Budgetcaraudio]

Boggs was litt you should on videoed us though we sunk 3 four-wheelers and we had 7

[@ReneGabe_]

Dangggg I never saw y’all

[@GG.Johnnie]

What’s the difference between the primary clutches I have seen stm 3p, wax rev x and 3rs ?

[@levibalazs3775]

any update on the boggs videos from the halloween ride?, marcos jeep crew checking in lol

[@ReneGabe_]

They’re both posted

[@beri232]

So what’s the difference between that RMT vs the Rev X HD which was supposedly made for side by sides with high hp

[@ReneGabe_]

No clue honestly

[@cb_jay9226]

What did you do with the 3 red little gaskets that comes on the stm belt screw ?

[@ReneGabe_]

Left them in the bag

[@kennethkirbow93]

Is that the 570 ?????

[@seanpair1382]

With my STM primary they recommended I lapped the end of the crank. Did they recommend that with QSC?

[@ReneGabe_]

If they did I didn’t see it anywhere

[@deeaikens9843]

Yeah I heard a lot about the primary Gettin stuck to the crank

[@ProjectVengeance]

curious what your rpms is at now when you are wide open throttle.

[@ReneGabe_]

I’ll test it out soon

[@nathanduenas442]

Can you use that same clutch set on a outlander

[@ReneGabe_]

Yes

[@meridianmuddaddicts4905]

wats the part number for tht maverick belt. im gunna run one on my 2021 rene

[@ReneGabe_]

422280364

[@kregankordsmeier9407]

Is it the stm secondary that’s responsible for your engagement going from 2600 to 1300rpms?

[@ReneGabe_]

No engagement deals primarily with the spring on the primary clutch

[@kregankordsmeier9407]

@@ReneGabe_ oh ok see I have cvtech primary stock secondary and there’s a significant lag in the throttle until ab 2600rpm then it jolts hard

[@lifewithflex4471]

@@kregankordsmeier9407 did u make any changes?

[@tylerharbour8562]

What color primary spring is in yours? if you don’t mind me asking

[@ReneGabe_]

I can’t even remember. Thought it was somewhere in that video

[@jreca]

Why did you choose that combo?

[@ReneGabe_]

I heard it was nasty and they were right💪

[@jreca]

@@ReneGabe_ did they come already setup with the proper weights and springs for your bike? Where did you order them from?

[@B1ou1nsGarage]

where did you order both from?

[@ReneGabe_]

Adam shumaker at qsc

[@johnnyjones549]

Who did you order the qsc fro

[@ReneGabe_]

Adam schumaker

[@johnnyjones549]

@@ReneGabe_ thank you

[@BlaiznTrails_Performance]

What helix is in the stm?

[@ReneGabe_]

Ummm not sure. It’s the one with engine brake I know

[@jammils38]

No lapping compound? You not even going to lapping it 25 turns? I thought that was a necessary thing to do with a new primary.

[@ReneGabe_]

I have never heard that before or seen it done but that doesn’t mean it’s not true.

[@jammils38]

@@ReneGabe_ that was what I was taught to do. And stm required it for theirs. But if you have not had any problems then maybe it's just a matter of preference?

[@ReneGabe_]

@@jammils38 I honestly don’t know but I’ve never heard that but I’ve never owned an stm primary either

[@Itsoundslikethat]

What did you pay for this combo from him?

[@ReneGabe_]

$1800

[@Itsoundslikethat]

@@ReneGabe_ how did you order?

[@ReneGabe_]

@@Itsoundslikethat from Adam shumaker hisself

[@Костя-у3ф]

👍👍👍

[@ReneGabe_]

💪