Cruise Control Issue Peugeot 307

[@pifandrei5743]

Ohhh . I see. Mine just says speed limiter but my cruise control is working. Only problem is that is not showing on display

[@bnyo]

In my 307 1.4 HDI, the Cruise setting is not available in the ecu, it is active in BSI, I don't know if anyone has tried the 2003 model, there are people who have chosen the vehicle as a Citroen C3 in pp2000 and adjusted it.

[@AnthonieBeuker]

I have the exact same issue., under the ECU configuration I see 3 options., all say 'without cruise control' the stalk is showing something on my dashboard, but it's not working., I was wondering., did you find the solution?

[@CM-1986]

if yours 307 is a year 2003/2004 you need to add extra wires into the BSi and ECU/BSM unit, to get this to work i was under the impression these would be pre-wired from factory to just be turned on via PP2000 like other years. but they were not pre-wired from factory, so you need to add extra wires, i might have the wiring info in a folder i could send you if i find it!? am sure it was only 3/4 wires to get this to work. i sold the car before i could do it.

[@AnthonieBeuker]

@@CM-1986 Did you add those wires? If yes, is it a hard thing to do?

[@mpgyoyo]

C M hello can you help me with the wiers i hav 206 cc from 2004 with bosch dnfu 7.4.4 if i am not wrong

[@pifandrei5743]

Do you mean the break switch and the clutch switch ?

[@mm_99321]

I have the same problem with it. Mine is 206 sw 90 hdi 2003 bosch, all the wires are present, but couldn’t make it to work. And I used PP2000

[@CM-1986]

Bosch system RHY should be able to turn this on, were did you go into on diagbox? (PP2000) it's been a while since I have used it but you need to turn it on via the engine ECU and BSI and maybe Comms unit.

[@mm_99321]

C M Thanks for that quick reply, mate. Well I went in to BSI and ECU, first I’ve tested the pedals and the cruise control stalk in the communication panel and everything seems to be responsive and computer seems to respond to the comands. The main problem that I bumped in to is when I try to select test by ecu > engine / automatic gearbox > rhy.......> the system (pp2000) gives me an error “pp2000 unknown reference, ECU being referenced”. I’ve looked online and people say just click ok > than keep pressing f3 untill you see the last menu and when i go to the cruise control select it to change it from absent to present - I only have the option for missing nothing else. And I really dont know what to do. I think problem comes from the software PP2000 that gives that glitch, but I am not sure. I have done everything that everyone is doing on their videos and cars, and still nothing. Would appreciate your help if you have some last suggestion for me - what to do

[@CM-1986]

@@mm_99321 Your ok, can you tell me what version of daigbox your using? also have you updated the interface (lead, box with the green led) i have had that issue with ECU being referenced but was still able to get it working.

[@mm_99321]

C M I’ve try a couple of times using diagbox from a virtual machine, but without a luck, but till this day I’ve been using PP2000 but the one that is separated from diagbox

[@CM-1986]

@@mm_99321 I use Oracle VM on a Windows 10 laptop no issues I use diagbox 7 and update it till 8 something I would need to check for you what version am on, i know it's a pain to install the software. The vci could need updated that's the interface firmware. If your lead is the cheaper version it might not be the full chip version that could be a issues as well. I will try and help you the best I can to get this working.👍

[@zwyczajny2290]

You can set cruise control to present and than can work! You even not try to change values

[@CM-1986]

It won't work on the 2.0 136bhp HDi I have set many cruise controls on Peugeot and Citroen you need to add extra wires it's well documented on forums.

[@-_Robert_-]

@@CM-1986 And if i have 4 wires in stop sensor?

[@CM-1986]

@@-_Robert_- apologise for the late reply, I had the 4 wires on the brake sensor and it still did not work. You need to add extra wires from the BSI to the ECU and it should enable it via diagbox. Remember these cars were in the change over period to VAN to CAN Bus I was told these via the dealership, if I can find the pin out PDF I will share.

[@-_Robert_-]

@@CM-1986 actually I have it activated and it work fine. 4 wires to break sensor and clutch sensor, no need anything more. Just activation 1st option without any info on instrument cluster and without limiter. But i discovered i don't need it at all.

[@CM-1986]

@@-_Robert_- well done on getting it to work. Can you tell me what year is your car?

[@mertbaskonyali6103]

Araç kaç model ve nerede yaptırabilirim