RV Backup Camera Installation

[@CruisinwiththeColemans]

UPDATE!!! We installed a new camera and we did an even better job. Check out the video here: kzbin.info/www/bejne/a4TZZ6Jmg7KSp8k

[@wendyburke3550]

Thanks , due to your video my husband and I figured out what we were doing wrong. The wireless camera was not working. I questioned why on ours the Camera was pluging into a port through the camper. If it is wireless you should not have to plug directly into the camper. When I watched your video and you were directly connecting into the lights and said that headlights had to be on, all made sense at that point. I determined that the camper is already hard wired and all we had to do is turn on the headlights. That is all it was,, we got horrible directions with our camera. We have had camera for over a year and have not been able to use. I keep telling my husband to look at you tube video, I solved this mystery with in a couple of minutes. This am he was out there over 2 hours and countless other times. Again Thanks

[@CruisinwiththeColemans]

It’s amazing how bad those directions are! I’m so glad it helped but so sorry you’ve been without the camera for so long! It’s going to be a game changer! Please stick around and subscribe. We’ll be back to posting RV content very soon!

[@CruisinwiththeColemans]

Here's our updated video where we don't go through middle light: kzbin.info/www/bejne/a4TZZ6Jmg7KSp8k

[@douglassmith2946]

Thanks for the video. I bought the A8 model. Followed your instructions and all worked perfectly. Saved me so much time. Thank you!!

[@CruisinwiththeColemans]

You’re welcome! We have a new backup camera video coming out in the next couple of months. Make sure you subscribe so you don’t miss it.

[@CruisinwiththeColemans]

Here's our updated video where we don't go through middle light: kzbin.info/www/bejne/a4TZZ6Jmg7KSp8k

[@joshuaerickson4140]

Thank you so much for this video. Took about a half hour and now I have an amazing set up. The SD card gives me piece of mind when someone gets impatient.

[@joerivers1768]

Great Job and very simple. When I installed mine this same way I found the power lead can be shortened so you don't have to shove as much wire into the hole and wrap a little electrical tape on the power plug so it doesn't come loose for any reason - remember, never say never.

[@CruisinwiththeColemans]

Good tip! Thanks for watching. If you don’t want to use the center light we have a new video out. The link is in the description.

[@donnaboykin1516]

Your demonstration was really great for fist timers putting a rear camera on our camper ..we did it without any problems thank you keep up the great work

[@CruisinwiththeColemans]

Thanks! We’re great at doing things for the first time too, lol. Make sure you hit that subscribe button!

[@mboy219]

Thanks for the video. I was on the fence about buying a camera because i didn't want to deal with running wires. I never in a million years would have thought to use the running light! Now I'm definitely ordering one!

[@CruisinwiththeColemans]

We’re glad we could help!

[@GetFitRecipiesKennyandKari]

same here.

[@sonnydudoit6804]

Honestly great video and install. Just ordered my camera and was scratching my head on how I will install. I didn’t want to drill any holes and this is a genius idea!! Bravo!!👏🏻👏🏻👏🏻

[@CruisinwiththeColemans]

Thanks. Let us know how the installation goes.

[@SPRINGTIDECREATIVE]

I’ve watched a few videos like this because I just bought a camera kit similar to the one featured in this video. But in this video they are installing it on an Apex trailer like mine, towed by an F150 like mine, and he even climbs up a telescoping ladder just like mine! I hope my camera mount bracket fits into the body of the clearance lamp like this one, so I don’t have to drill any holes!

[@CruisinwiththeColemans]

So glad we could help! If you ever get brave enough to drill that hole, we finally did. There’s a link in the description to the newer video or let me know and I’ll comment with the link.

[@SPRINGTIDECREATIVE]

@@CruisinwiththeColemans Yes, thanks, I watched your newer video after posting my comment here, and I’m going to do it that way. The instructions that came with my camera kit are useless too. There are some strange-shaped red plastic clips in the hardware bag that I have no idea what to do with. They’re not mentioned anywhere…not even in the manufacturer’s video. Oh well.

[@CruisinwiththeColemans]

@@SPRINGTIDECREATIVE I believe those clips are for wiring the camera directly into your fuse box in your truck, but I’m not totally sure.

[@JayZoop]

You both are fun together. I have a 7" screen and just put it in a box on the floor. I don't want it covering my windshield.

[@CruisinwiththeColemans]

Thank you, we appreciate your kindness! Glad you found a solution! Take care!

[@chargriller6547]

LOL - My wife and I have never had a backup argument either. 😂 Great video. Got a similar camera system for one of my cars. It was under a different brand name but is obviously made by the same manufacturer. Same useless instruction book and videos. I muddled thru the install which took way longer than it should have. That being said I loved the quality so I bought an RV/Truck system for my travel trailer from the same company. Knowing the install book and videos were likely useless I googled and found your video. Based on your experience and my own, made the install on my travel trailer and towing truck a breeze. Thanks so much for sharing. Quick story when my wife and I took our travel trailer camping for the first time. We were in our early 50’s at the time. I was sitting outside the trailer with a cold beverage just enjoying nature when an older couple probably in their late 60’s drove up with a large 5th wheel. The wife jumped out to aid the husband back it up. The husband was trying to back up while their little yappy dog was running back and forth on the trucks dash. So with the dog constantly barking and the wife yelling “NOOOO your other Right” etc the poor frazzled guy finally parked in his spot. At that time my wife jumped out of the trailer asking what I was doing. I responded with “ I was just watching us in about 15 years.”

[@CruisinwiththeColemans]

That is hysterical! Glad the video was helpful.

[@CruisinwiththeColemans]

Here's our updated video where we don't go through middle light: kzbin.info/www/bejne/a4TZZ6Jmg7KSp8k

[@rickreed7774]

Super huge help I've had a leekooluu wireless for over a year and just hooked it up today super simple...I wired to my tail light on my 5th wheel now I can hook up to my boat and side by side trailer with out any help. Awesome information thanks dude.... Rick

[@CruisinwiththeColemans]

Glad it helped! We appreciate the feedback!

[@trykkid]

loved the concise nature of this video AND the modest humor too. followed ur advice but i used a 2 cam set up. installed the other down low to keep an eye on my cargo rack. powered that from the tail lite. works on the same circuit. great idea replacing the center clearence lite, thank u for the insites.

[@CruisinwiththeColemans]

Thanks for watching!

[@CruisinwiththeColemans]

Here's our updated video where we don't go through middle light: kzbin.info/www/bejne/a4TZZ6Jmg7KSp8k

[@katefandetti6345]

Good video - I'm sold....BUT has is this camera performing not, a couple of years later?

[@CruisinwiththeColemans]

We have been very happy with the camera's performance. No issues after 3 years.

[@CruisinwiththeColemans]

The camera held up for about 4 years. Here's our updated video where we don't go through middle light and use a better camera: kzbin.info/www/bejne/a4TZZ6Jmg7KSp8k

[@garyrasmussen1794]

Thank you for posting this. You rescued me from the endless hours of trial and error. I had exhausted all ideas until you mentioned (about 6:00 on you video) “...White should be negative and green positive...” Whatttttttttt????? In housing construction, something I’m a little more familiar with, green is always ground. So with fear and trepidation I switched the wires and wahlah, a picture appeared on my monitor. Thank you, thank you, THANK YOU!

[@CruisinwiththeColemans]

Learning 12v wiring has been an experience. I’m glad it helped someone else!

[@chrisseibers2921]

I havent attempted to attach my camera yet, but i feel like i dont need to watch another video. I also love all the sound effects. Definitely had some giggles during this one. Thank you for making this video.

[@CruisinwiththeColemans]

Glad we could help. Happy camping!

[@sandywilliams6646]

Hubby just installed this camera system based on your video instructions. Thank you! This video really worked for us.

[@CruisinwiththeColemans]

Glad to hear it helped! Please subscribe, if you haven’t already, so we can continue to bring helpful videos. ❤️

[@sandywilliams6646]

@@CruisinwiththeColemans Did subscribe and shared this in the hybrid campers Facebook group I am in. Thanks again!!!

[@CruisinwiththeColemans]

@@sandywilliams6646 that just made our day! Thank you so much!! ❤️❤️

[@sandywilliams6646]

@@CruisinwiththeColemans ok...got one little backlash in the forum...most everyone loved this . But someone mentioned that Fed law is that you have to have that light - 3 lights. And that it also wouldn't pass inspection...of course we are in NC so our state doesn't require inspections on trailers to tag them . Have you had anything on this? Love your videos! Actually read further down in the comments an I think we'll do what you did...just keep all the parts from the light and if needed just reinstall if it becomes a problem. For now this works!

[@CruisinwiththeColemans]

We have had several people comment about that. We’ve never been stopped and our law enforcement children said they would never pull someone over for it. But… in the event of an accident, it could be a problem. When I replace the camera eventually, I will probably do it “the right way.”

[@firedog6able]

Hello..Your video shows camera mount using marker light but link to purchase camera shows different mount..looks like a furrion mount. I would like to use marker light set-up but cant seem to find anything. Any suggestions?? Thanks

[@CruisinwiththeColemans]

The camera on Amazon has been updated several times since this video came out. The current version does come with the Furrion mount. I mounted the metal piece directly into the housing of the marker light and then filled it with a piece of latex and some silicon to make it watertight. The current version of the mount has little metal “fins” that might need to be bent up or cut off. Hope that helps.

[@MrBowNaxe]

Thanks guys! I was going to run power to my camera but your idea of using the marker lights for power makes a lot of sense. Thanks for sharing.

[@CruisinwiththeColemans]

Glad it helped!

[@CruisinwiththeColemans]

Here's our updated video where we don't go through middle light: kzbin.info/www/bejne/a4TZZ6Jmg7KSp8k

[@prdpapak2563]

Just bought this exact system to replace the non-working system on our motorhome. Thanks for this awesome installation video!

[@CruisinwiththeColemans]

Thank you for watching! We’re glad it helped! Brian & Michelle

[@Mr2ndkings]

PrdPapa K ... did your kit come with a slightly different bracket for mounting the camera than the one on this video? I was going to order but noticed the design change in what is available now on the same product. Thanks. David Trousdale

[@prdpapak2563]

@@Mr2ndkings I bent the ears of the bracket up then it fit perfectly into the light housing. I also had to auger out the mounting holes a little so they would line up with the existing mounting holes on the RV.

[@Mr2ndkings]

@@prdpapak2563 Thanks. Just ordered mine.

[@prdpapak2563]

@@Mr2ndkings I love mine, I think you'll be very happy!

[@kipbryant2036]

Great video. Worked exactly the way you presented. Thank you for taking the time to show how to properly install the camera.

[@CruisinwiththeColemans]

Thank you Kip, that means a lot!

[@EpicRV]

Back up cameras are so important. Your video was great at showing someone how to do install it. We haven't had to put on in on our RV, but we did on one of our SUV's several years ago. Glad we connected and look forward to your videos.

[@CruisinwiththeColemans]

Thanks. I’ll be getting back to editing soon. We got a backlog of videos to get out!

[@EpicRV]

Cruisin' with the Colemans We understand. I have several I need to edit. Lol!

[@terryalthoff165]

Thanks for making the installation so easy. I actually have an Apex trailer and a F150 so this was perfect. I did want to address your mounting issue. What I did to lower the congestion was run velcro straps through the double slots on each side of the bracket (I also attached the double-sided bracket pad to the bracket but did not take off the second tape as padding) and strapped the monitor to the rearview mirror since it is not used while towing ... it becomes the new rearview mirror. I wish I could have added pics.

[@CruisinwiththeColemans]

That's a fantastic idea! I'm going to try that out. Make sure to hit the subscribe button so you don't miss our next video.

[@trykkid]

this a great idea. i followed this plan and have my monitor up near the roof liner now. my only concern is whether the attachment of the stock rearview mirror to the windshield will hold up to the extra weight of the monitor... ?

[@terryalthoff165]

@@trykkid I have had no issues the extra weight on the rear view mirror. It has worked great for me 😊

[@CruisinwiththeColemans]

Here's our updated video where we don't go through middle light: kzbin.info/www/bejne/a4TZZ6Jmg7KSp8k

[@christineglosser1201]

Are you able to move the display inside your camper and use it as a security-type video? I would guess it could be plugged into the 12v plug inside the camper on the wall???

[@CruisinwiththeColemans]

I don’t see why not but we have not tried to do it. Thanks for watching!

[@christineglosser1201]

Thinking about it…car running lights are needed for the camera to work. So it probably won’t work inside the camper. 😔

[@CruisinwiththeColemans]

Hmmm, good point!

[@oldnotdead9868]

Okay your video looks pretty straightforward this I already knew because I'm doing this to mine but wiring it into running lights the camera will not have no power unless you turn your lights on

[@CruisinwiththeColemans]

We do keep our lights on to run the camera.

[@beverlycampbell9555]

Just got my camera from Amazon and was looking at Amtiflo videos to install (crap). Yours was so helpful. Full of confidence to tackle the job thanks to your video

[@CruisinwiththeColemans]

Thanks! Make sure you check out the other comments here because there are some additional good ideas.

[@rbrown2895]

Good job on the install and the video. Thanks!!

[@CruisinwiththeColemans]

Thank you! Subscribe because we’re always up to something good! 🙌🏼

[@arkbuilder2012]

Not sure if your link is the same model camera system. I do know the mounting brackets provided will not cover the center light on our Jayco Eagle 5th wheel. I was really hoping to avoid drilling more holes. Still working our way through this one.

[@CruisinwiththeColemans]

They have made slight changes to the product since our installation. I believe that you can trim down the new bracket to fit into the light assembly.

[@StephenJStephen_Photography]

Thank you for a very good, straight forward DYI video. It looks like you two have fun together. All the best!

[@CruisinwiththeColemans]

Thanks for watching!

[@ericsinotte5524]

Very helpful! I follow your steps and it runs well😎. Merci beaucoup! Thanks a lot Eric from Québec, 🇨🇦

[@CruisinwiththeColemans]

Glad we could help out Eric! Please subscribe to help our channel grow and we hope to continue to provide helpful content!

[@davidlewis3427]

Thanks, very helpful. May I ask what manufacturer you purchased for your telescoping ladder? Max Weight? Thanks.

[@CruisinwiththeColemans]

Hi David! Glad the video was helpful! The maximum weight on the ladder is 330 pounds. We purchased it in 2017 and love it still today here’s a link: amzn.to/481avuf

[@Mlessard1392]

So glad I decided to look up videos before installing. This was an excellent idea and I did the same and was done in no time lol. Works great and I don’t mind at all having headlights on while driving. Thankfully the truck with yell at me if I forget to turn them off. Very helpful

[@CruisinwiththeColemans]

Glad it was usefulness info!

[@CruisinwiththeColemans]

Here's our updated video where we don't go through middle light: kzbin.info/www/bejne/a4TZZ6Jmg7KSp8k

[@marcosleal8381]

I liked the solution, congratulations for the video!!!

[@CruisinwiththeColemans]

Thank you very much!

[@06ridgelineowner34]

I installed a similar wireless camera in my class C last year. I wish I would have just mounted it in my middle light like you did. I looked at a different video, drilled a hole above the middle light and had to pull things apart inside my "bedroom" to do the wiring. Just pulling out the middle clearance light and using it's wiring would have been so much easier..and much simpler to make it waterproof.

[@Lauralietx]

I did mine like you did yours but I am having horrible time getting all the words stuffed back into hole behind clearance light !! Any suggestions??

[@Lauralietx]

Wires not words lol

[@CruisinwiththeColemans]

Sometimes the simplest solution is the best solution, only time will tell! Make sure to hit the subscribe button so you don't miss our next video.

[@CruisinwiththeColemans]

I used some needle nose pliers to coax it back in. I was stressed out that the connection would come loose but it's held so far.

[@iglapsu88]

Very nice! No big deal with daytime running lights on. You can switch to auto lights white gets dark enough. Great job!

[@CruisinwiththeColemans]

Thanks!

[@frankbianchini7716]

Thanks for this video. Using the center light on the back worked GREAT!!!!!!!

[@CruisinwiththeColemans]

That’s great to hear!

[@v908]

Violated DOT regulations though. Pulling power from the light is fine, but the camera should be mounted separately so you don't eliminate one of the 3 (required) lights.

[@GetFitRecipiesKennyandKari]

That was a pretty awesome video. Thanks for the help. I also clicked the link in the video description and seen a whole different monitor and camera. Do you know any new manufactures that have something like you put in? I need to go off that center running light also. Thanks Kenny

[@CruisinwiththeColemans]

It’s technically the same camera in the link but they have done some upgrades so the mounting bracket is different now. You don’t have to use the Furrion adapter. There are “wings” on the other piece that could be clipped off and I think it would still work with the mounting method we demonstrated.

[@GetFitRecipiesKennyandKari]

@@CruisinwiththeColemans Thanks guys for the info.

[@ronmcc4]

We just bought the exact same camera system and found your video very helpful and entertaining as well. Thanks for posting the video.

[@CruisinwiththeColemans]

Glad it was helpful! Thanks for stopping by! We appreciate your support! - Brian & Michelle

[@edyoung6573]

Great Job!!!! just using the running light!! Thats what I'll be doing!! Thanks for taking the time of making this video! Helped me out a bunch!!

[@CruisinwiththeColemans]

Glad it was helpful.

[@CruisinwiththeColemans]

Here's our updated video where we don't go through middle light: kzbin.info/www/bejne/a4TZZ6Jmg7KSp8k

[@jasonpowell6263]

Awesome video! Thanks so much for sharing. You made it look so easy. Safe travels for you always.

[@CruisinwiththeColemans]

Thanks for watching! We hope your camera is serving you well!

[@roysims7710]

I bought the same AMTIFO rear view system easy install great monitor picture thanks for video

[@StorytellerSueW]

Thank you thank you! I have been overthinking how to hard-wire my new wireless cam (very similar to yours) into an old 1998 Bounder with a dinosaur Panasonic system. I finally realized I don't need to do that yet up front on the monitor end. And THIS was exactly what I needed for the camera back end. I have an existing camera spot with a plastic protective hood, and this fits perfectly inside it. And my mobile RV tech is coming this week to address some electrical issues and replzace an interior outlet, so perfect timing for him to wire this in, too. Yay!

[@CruisinwiththeColemans]

Glad it was helpful

[@tonydeleo3642]

Two suggestions, seal the hole in the bracket where the wire comes out to keep weather out. ALSO, you might check with law enforcement or highway patrol to confirm that removing the center marker light is legal.

[@CruisinwiththeColemans]

We did seal that hole and we’ve had no trouble with the po-po so far 🤞🏼

[@ROGERTAYLORSGRL77]

What did you use to seal the hole?

[@CruisinwiththeColemans]

Crystal BORDERS I used a latex dish glove cut down to size and sealed it in place with clear silicone.

[@TouchofAlaska]

Yeah, removing that light is not legal. Autos and trailers over 80" wide require those lights. I would suggest installing the camera a couple inches above the center light.

[@CruisinwiththeColemans]

Here's our updated video where we don't go through middle light: kzbin.info/www/bejne/a4TZZ6Jmg7KSp8k

[@michaelderosieratc]

Great video, thanks! I've go a Coachmen and a new Rohent I need to install. I'm hoping the wiring is the same and as easy as you had! Any way you could add a bit of video to this that shows how well it works when backing up? Like what kind of view do you get with the camera up top? (I have the same 3 lights up top). And what kind of angle is the camera finally set at for most use? Anyhow, thanks for the video, I really like the banter between you two, ha!

[@CruisinwiththeColemans]

The camera has a pretty wide view. I have it pointing down pretty much as far as I can so that we can see a car that might get too close in our blind spot. Thanks for watching and good luck with the install.

[@rafyperalta9246]

thank you for sharing how to do this. I am looking to do this to my trailer but I was wondering do you know if removing that light causes an issue with the DOT?

[@CruisinwiththeColemans]

It is technically a violation but we have never had a problem other than about 40 comments above about getting pulled over. lol

[@CruisinwiththeColemans]

Here's our updated video where we don't go through middle light: kzbin.info/www/bejne/a4TZZ6Jmg7KSp8k

[@ronciurla9170]

After watching the video I'm concerned with this installation due to the risk of a water leak. In the video it appears there is an open hole directly into the RV where the wires run through the camera mounting bracket. How did you close off this leak path? Did you apply some type of caulk/sealant in that hole to prevent water intrusion? Water will make its way into the wall of the RV through that hole if not sealed properly.

[@CruisinwiththeColemans]

Yes, we used a piece of latex and silicone caulk to seal the hole. Also, it’s helpful to make sure there’s a bend in the line so the water drips off rather than running down in.

[@MrDan0315]

@@CruisinwiththeColemans Thanks, I noticed this too and scanned the comments for someone to ask or I would've. Great video, I just got mine today for my new (to me) motorhome and a quick youtube search brought me here. Look forward to watching some of your other videos.

[@thingz2c]

Thank you for the video. Out of all the videos I watched on this, yours is truly helpful. I am mounting my camera on a Class A motorhome and was trying to figure out how to make it a rearview mirror, your video stated to turn the head light on, that makes sense. Thank you again. Keep on RV'n.

[@CruisinwiththeColemans]

Glad we were able to help.

[@scard3128]

Hello! This is such a great idea. Has there been any concern or question of this jeopardizing the requirement for 3 running lights at the rear top of the rv? Thank you!

[@CruisinwiththeColemans]

Thank you! We haven’t had any issues or concerns. Glad we could help!

[@CruisinwiththeColemans]

Here's our updated video where we don't go through middle light: kzbin.info/www/bejne/a4TZZ6Jmg7KSp8k

[@lizannnelson249]

Just the video I needed! Clear and concise. Thanks for taking the time to share this.

[@CruisinwiththeColemans]

Glad it helped! We hope you subscribe to our channel and come back for more helpful videos.

[@CruisinwiththeColemans]

Here's our updated video where we don't go through middle light: kzbin.info/www/bejne/a4TZZ6Jmg7KSp8k

[@nvdube]

Great video! Super helpful! ’m a visual guy, do you have a photo/video of how you sealed the hole with the wires? I’m hoping to install mine this weekend and want to be sure i have everything needed when i go to install.

[@CruisinwiththeColemans]

Thanks! We don’t have any photos but we used silicone caulk and silicone film.

[@CruisinwiththeColemans]

Here's our updated video where we don't go through middle light: kzbin.info/www/bejne/a4TZZ6Jmg7KSp8k

[@samihakami1436]

Thanks great video may i now the name and the model & what where i can order.

[@CruisinwiththeColemans]

Sami, there’s a link to the camera in the description. Enjoy!

[@CruisinwiththeColemans]

Here it is: amzn.to/3wwxbjR

[@wanderinwilds]

Love that you should be ok!? 🤣🤣 love your vlogs - will be watching more 🤩 Michelle keep that camera rolling 😂 love the music and sound effects ! X Debs and Mark

[@CruisinwiththeColemans]

Lol thanks! ❤️❤️

[@thomasvliet2101]

I found this video very helpful from the wiring colors for positive and negative to the mounting of the camera bracket using the marker light base. I had to buy a new marker light and use the base from that as the one on my trailer was more rounded in the corners and the bracket would not fit inside it. Tractor Supply had a marker light with square type corners and the bracket fit into that nicely. Thanks!

[@CruisinwiththeColemans]

Glad it helped! Thanks for watching. - Brian & Michelle

[@kathleenrutherford733]

Thank you so much for this video!! I loved that you showed it step by step, it's exactly what I needed!!

[@CruisinwiththeColemans]

We’re so glad it helped!! Let us know if you need anything else! - Michelle & Brian

[@johndangelo865]

Hope it works I will try it now. Good video

[@CruisinwiththeColemans]

Thank you! Keep us posted on how it works out.

[@CruisinwiththeColemans]

Here's our updated video where we don't go through middle light: kzbin.info/www/bejne/a4TZZ6Jmg7KSp8k

[@chamiv]

Thanks guys for this video. I installed this on our old Class C RV following these instructions.

[@CruisinwiththeColemans]

Thank you for watching! We’re glad it helped you! Brian & Michelle

[@princeofallnegros4035]

Thanks so much for this. I was going crazy not knowing how to get power.

[@CruisinwiththeColemans]

Glad it helped!

[@ericbaumgartner6558]

Those three center running lights are required by law if the vehicle is over a certain length and width. I watched another video where the dude talked about how he got pulled over for doing this exact same thing on his fifth wheel. good luck.

[@CruisinwiththeColemans]

We understand the risk, thank you

[@CruisinwiththeColemans]

Here's our updated video where we don't go through middle light: kzbin.info/www/bejne/a4TZZ6Jmg7KSp8k

[@scottthompson1893]

Thank you for your video. I had literally just tossed the instructions provided with the unit to the side when you guys commented how useless they were.

[@CruisinwiththeColemans]

Right?!?

[@johnharrison5098]

can u run 2 cameras in tandem or do i need to run a separate reverse camera system from my normal backup camera?

[@CruisinwiththeColemans]

We have not tried so we can’t tell you. I’m sorry!

[@jesserevilla992]

Great walk through. Others are far to complicated you kept it smart & simple. Thank You

[@CruisinwiththeColemans]

Glad it was helpful! Thanks for watching.

[@bowman4502]

You’re a rock star. Thank you!

[@CruisinwiththeColemans]

You’re welcome!!

[@CruisinwiththeColemans]

Here's our updated video where we don't go through middle light: kzbin.info/www/bejne/a4TZZ6Jmg7KSp8k

[@gunzofthenavarrone8293]

Installing today. Did you just shove a bunch of silicone into the hole where the cable comes out of the Trailer to keep water out?

[@CruisinwiththeColemans]

No because I didn’t want to make removal/replacement more difficult in the future. I used a piece of latex to cover the hole and silicone to seal it.

[@nesbittjohn]

It looked like you still had a fairly large hole in the middle of the original running light mounting plate. Did you have to fill that with anything to keep things water tight?

[@CruisinwiththeColemans]

Yes, I used a piece of silicon and caulk to plug it. Also, leave a loop in the cord so water doesn’t run in.

[@Mr2ndkings]

Just getting around to looking at my install and noticed that the cable coming directly out of my camera has a rubber grommet which will not pass through the hole in the bracket. In your install, there was no visible grommet on the cable as you fished the cable through the hole in the bracket. What did you do with the grommet? Cut it off?

[@CruisinwiththeColemans]

I believe that the grommet is a newer addition as the product has been upgraded. I would remove it if it doesn't fit into the opening.

[@frankminneci2966]

Perfect video. This guy is awesome

[@CruisinwiththeColemans]

Thanks!!!

[@Pantherjonvideos]

Pretty neat..And good job not dropping any of those small screws! I have the same camera system, just wondering how well installation will be with the trailer already wired for the Furrion camera? Will see when I go attempting to install it..But, at least I know that this unit has good video resolution! :)

[@CruisinwiththeColemans]

Thanks! We’ve been happy with it over the years. Let us know how the Furrion setup works out.

[@Pantherjonvideos]

@@CruisinwiththeColemans Installation went fairly well..The provided 'adapter' to go on the Furrion rain shield gave me the most struggle. The holes were ever so slightly off, and I had to use longer screws to secure it. Also, the camera bracket screws were too small, had to use slightly larger washers so they would be secure(only had 2, hopefully 2 out of 4 is secure enough, knock on wood..lol)..THEN there is no room to put the wiring away, so it just kind of dangles..Picture is nice a bright and clear, so, overall it is worth the little bit of struggle to get it installed..Will see how it performs on our next RV trip!

[@CruisinwiththeColemans]

Oh wow, thanks for letting us know!

[@5247charles]

Thanks for the video guys. This is exactly what I was looking for after getting a good camera with poor instructions.

[@CruisinwiththeColemans]

Glad we could help! - Brian & Michelle

[@leorivard638]

Very good video i really enjoyed it but you don't have to use the headlights use the parking lights instead, thank you for the video

[@CruisinwiththeColemans]

Thanks. That didn’t really work well for us.

[@TheJourneyAwaits]

Thank you guys for sharing this. Do you still like this brand of back up camera?

[@CruisinwiththeColemans]

Oh my gosh, yes! We still love this camera. Thanks for asking, sorry I’m slow to reply. 😏

[@CruisinwiththeColemans]

It lasted about 4 years. Here's our updated video where we don't go through middle light: kzbin.info/www/bejne/a4TZZ6Jmg7KSp8k

[@shirleystanley3299]

Can you please provide the information on the camera you purchased? I would like to buy the same one. Thank you.

[@CruisinwiththeColemans]

Hi Shirley! Absolutely, the cameria is the Amtifo Digital Wireless Backup Camera and Monitor. Here is a link on Amazon: amzn.to/36ywuJc You can also find the link in the description of this video. Hope that helps! - Michelle & Brian

[@loveicefishing47]

How did you fill the large hole for the wiring?

[@CruisinwiththeColemans]

We covered it with a piece of latex and silicone caulk.

[@picwick57]

easy install but legally because of trailer width you are to have 5 rear clearance lamps as per code. You may never get hassled but just as easy to feed wires for camera just long enough below lamp to feed power to camera in it's own location. But I get why you opted to do it this way😎

[@CruisinwiththeColemans]

Thanks!

[@CruisinwiththeColemans]

Here's our updated video where we don't go through middle light: kzbin.info/www/bejne/a4TZZ6Jmg7KSp8k

[@nyarlathotep74]

5:07 it would have been hilarious if he had pretended to get shocked. Something I would have done, anyway LOL. Great video!

[@CruisinwiththeColemans]

Jesse, that was an early video. Check this out for that exact sound effect: kzbin.info/www/bejne/i2fZfZ6VispnodU 😆😆

[@nyarlathotep74]

@@CruisinwiththeColemans BZAP! lol you earned yourself a new sub. Excellent vids!

[@CruisinwiththeColemans]

Haha! Thanks!

[@edcones2948]

How has the camera held up over two years? Still doing fine? Thanks for the video.

[@CruisinwiththeColemans]

Two years later, still no problems! Thanks for watching, hope it helps. - Brian & Michelle

[@CruisinwiththeColemans]

The camera held up for about 4 years. We just updated to a new model. Here's our updated video where we don't go through middle light: kzbin.info/www/bejne/a4TZZ6Jmg7KSp8k

[@3ccbentz]

Did you caulk the entire hole where the cords went down in?

[@CruisinwiththeColemans]

Yes with a silicone caulk.

[@petebowman6275]

Best video yet that I've seen about installing a back up camera. Thanks for posting! PS. I nearly freaked out when I 1st saw you... do you know you look a lot like Glen Beck? Ha ha! Have a great day! Thanks again.

[@CruisinwiththeColemans]

Haha - not Glen Beck - but glad we could help! Have a great week, please stop by our channel again! - Michelle & Brian

[@CruisinwiththeColemans]

Here's our updated video where we don't go through middle light: kzbin.info/www/bejne/a4TZZ6Jmg7KSp8k

[@daviddewitt94]

Commenting now - 2+ years later. How did the camera mount hold up? I was worried it would giggle free and be dangling. Thanks

[@CruisinwiththeColemans]

We’ve still had no problems with the mount or the camera itself. I check it anytime I’m up on or around the roof just to make sure its still on tight and is sealed… no problems!

[@CruisinwiththeColemans]

Update - it was finally time to get a new camera. Here's our updated video: kzbin.info/www/bejne/a4TZZ6Jmg7KSp8k

[@jopierre17]

You have just saved me hours. Super tighty install!

[@CruisinwiththeColemans]

You’re welcome!

[@donnellg2032]

Thank you for pre-empting the argument that would have occurred installing one of these...

[@CruisinwiththeColemans]

Lol happy to help! Subscribe for more happy marriage tips. 😆

[@brianpeters2695]

I like the ladder. My big box do everything ladder is good but a bit of a pain.

[@CruisinwiththeColemans]

We had a big box ladder too but it was a huge pain. This was a super convenient. Thanks for watching!

[@leedavis9696]

What is the brand of this camera? I could not find the link. thanks

[@CruisinwiththeColemans]

Hi Lee, the link is in the description, and here it is: amzn.to/3sCGYDl

[@elaineg4921]

Good info. Thanks... you did calk the hole after the wires were pushed in? Happy travels

[@CruisinwiththeColemans]

I used two pieces of glove to make a flap for the wires to run through so that it can be adjusted and pulled back out if needed.

[@seangraham3419]

Two pieces of glove? I don’t understand.

[@CruisinwiththeColemans]

I used a latex dish glove cut down to create a seal. Glued in place with silicone caulk.

[@mattnjules]

Ok, so have you had to use the red "reset" button on the wire, since you've installed this? I caulked to seal, and it be a real PIA if I have to access this red button ever again

[@CruisinwiththeColemans]

Thankfully, I never have needed to reset the button. Fingers crossed 🤞🏼

[@jpgelb]

not sure if you get my reply to a reply. i was hoping for more info on how you sealed the hole where the light was. how'd you hold the glove to the hole? everything else seems clear from your video, except how you sealed that hole.

[@CruisinwiththeColemans]

I ended up using a cut up dish glove and clear silicone to seal it up. No problems so far!

[@JCharlesoutdoors]

I'm gonna need to do this project, thanks for look ahead.

[@CruisinwiththeColemans]

Glad it helped! Let us know if we can help out anymore. Thanks for watching!

[@nospam3409]

How long is your travel trailer? I'm curious how far the signal will reach. How well can you see with it at night? Also, you can just use your parking light if you don't want the headlights on. Same issues with remembering to turn it on though.

[@CruisinwiththeColemans]

Our trailer is 30'. We can see everything back there both day and night. It has been almost 2 years and we will still love it. - Michelle & Brian

[@nospam3409]

@@CruisinwiththeColemans Thanks! I have a cheap wired camera on my 25' camper. I agree, it makes a HUGE difference. We just upgraded to a 34' bunkhouse. I think I'm going to go with the A8 version for it.

[@ddatoka]

Good video, whats the little red button on the other wire with the camera power lead ?

[@ddatoka]

Never mind i read the manual .LOL .Mounting mine in that center light hole like you did .See if i can find a rubber grommet to run the wires through .THANKS

[@CruisinwiththeColemans]

Glad it was helpful

[@pableauxsporch7511]

Great video. Now I know how. Thanks

[@CruisinwiththeColemans]

Glad to help! Hope you subscribed as we will continue to put out videos you may find helpful. Thanks! - Michelle & Brian

[@dannycamacho128]

great video

[@CruisinwiththeColemans]

Thanks! If you are looking for an install video with using the center light, we can send you a link to our latest video.

[@mimocz73]

Thank you for the video, I just got my camera.. Tomorrow installation day. Cheers

[@CruisinwiththeColemans]

Glad it helped, let us know how it goes! Make sure to hit the subscribe button so you don't miss our next video.

[@mcopilot]

wow thanks you gave me a great idea on how to mount the camera without drilling into the back thanks, where did you get that ladder?

[@CruisinwiththeColemans]

Glad it was helpful. Here’s a link for the ladder on Amazon: amzn.to/2DqFx5e

[@terreystreath1652]

Great video! Can you give us info on your RV GPS?

[@CruisinwiththeColemans]

It’s a Garmen RV GPS and we love it. Here’s the link on Amazon: amzn.to/33MYzMt

[@terreystreath1652]

Works like a charm! It was just that easy to install. Do you know which menu setting changes the direction of the image? The way it is now the image is reversed. Stuff on the left shows up on the right. No biggie, just figured you have discovered the answer to this.

[@CruisinwiththeColemans]

We did work that out, but without it in front of me I couldn’t tell you how to do it. I want to say it was from the main menu button at the bottom center of the screen.

[@onelik]

Does it have lag or a delay? When you step on your break does the camera have a light to replace that break light?

[@CruisinwiththeColemans]

The camera replaced one of our running lights, not a break light. We still have 4 other runners across the top. There are lags from time to time but I think you are going to find that with any camera.

[@twood3270]

Mr./Mrs. Coleman. How is the camera 'holding up' these days? I'm worried that whichever backup camera I purchase, will crap out within the first 6-12 months.

[@CruisinwiththeColemans]

It’s still working like a champ. We’ve had no issues since installation except to check the seal and guarantee that it’s still secure.

[@twood3270]

@@CruisinwiththeColemans I appreciate your reply and this helps my thinking alot. Regards

[@TheBadSandys]

Thanks for the help. Was there anything else you had to buy to mount directly to the light fixture like that or was everything you needed included?

[@CruisinwiththeColemans]

The only things I needed were the silicone and a piece of latex for a gasket to seal it better.

[@CruisinwiththeColemans]

There wasn't anything else we needed to buy. Here's our updated video where we don't go through middle light: kzbin.info/www/bejne/a4TZZ6Jmg7KSp8k

[@keithkimbrell8616]

Nice video. Easy install. But you did not secure the monitor to the dash. It has the potential to go flying in the event of an accident and possibly injure an occupant of your vehicle. Something to think about.

[@CruisinwiththeColemans]

We didn’t secure for the video. We’re good though. Thanks!

[@johnhornsby6759]

thank you for the video very helpful.

[@CruisinwiththeColemans]

Glad we could help!

[@jrahman38]

I got the camera from Amazon today, but it does not have the camera mounting bracket/adapter you have used. Can you please recommend where to get the bracet which does not require me to put a hole

[@CruisinwiththeColemans]

I mounted the camera in the existing housing for the running light similar to this one: amzn.to/3oo3Vrb

[@dennisbeauchamp6193]

very helpful thanks for sharing.

[@CruisinwiththeColemans]

Absolutely, glad it helped!

[@kennybaseball17]

great video, how long is your trailer?

[@CruisinwiththeColemans]

30 feet including hitch. Thanks for watching!