Thanks to this video I was able to fix my truck. Mine would crank over as well and only turn on with starting fluid. Then started dying at idle. But if I set the idle like 250rpm higher, it would stay on. My mechanics and I thought it was a weak fuel pump. Couldn’t find a new crank sensor, so got a used one from the junk yard. Cut an 11/16 just like yours. And swapped it out. Then truck turn right on after that. I’ll be returning the fuel pump, and not wasting $1000. I appreciate you sharing your knowledge
@mannyayala79792 жыл бұрын
I’m glad it all worked out. God bless you.
@jameserickson25232 жыл бұрын
Fuse on ecm could be blown which let's no power to fuel solenoid shut off switch
@jesussaves517612 күн бұрын
I’m going to try this for sure! Same problem
@terrancex7988 Жыл бұрын
I recently bought a 1996 international eagle, the guy said that it was sitting for a while. It has a N14 Cummings red top. Thanks for this video i know where to start if she don't fire up
@hectorguajardo6392 Жыл бұрын
Once you did the investment on putting a new fuel pump, you should also replace your fuel hoses and return lines that goes to the back of your fill tanks. Probably dirt or pieces of rubber from your hoses clogged your check valves it’ll help with performance and also starting performance.
@peterfong2241 Жыл бұрын
The N 14 select plus is my favorite !!
@lestvee2001 Жыл бұрын
Thank you. Gotta a 99 Muni bus (SF) that I'm converting & I thought it was the filter/primer. You da man!
@chad2822 жыл бұрын
Thank you for this video. Im having the same problem. 2003 International 9100 I I have changed the cam position sensor about five times in the last 13 years that I have owned the truck normally I will get a fault code when it goes bad but this time I did not and I was about to change the fuel pump for $1,000 thanks to you my friend I don't have to do that
@carloss93602 жыл бұрын
Excellent video and perfect explanation 👍
@vickolover4 ай бұрын
Great papa Gracias 👍
@billw4746 Жыл бұрын
Nice video I was having trouble with an N14 it turned out to be the fuel shutoff solenoid.
@mannyayala7979 Жыл бұрын
I’m glad you were able to figure it out
@lukenburg2 жыл бұрын
I’ve done the same in the past! I always say: man I wish I would’ve started with the $60 part 😂
@mannyayala79792 жыл бұрын
I know. The pump was super expensive. 😂😂
@chrisparks19982 жыл бұрын
Thanks so much mine was doing the same thing...
@cesarjorgemurillobarientos18132 жыл бұрын
Very good master
@luiscolon3045 Жыл бұрын
Ayala gracias ,por la informacion
@vicpetrishak10772 жыл бұрын
.008 - .012 end play on the 3 bolt camshaft cover . Camshaft has to be tapped back towards bell housing before checking end play .
@burkevinell Жыл бұрын
I always carry a spare crank sensor in my truck. Cheap insurance. I found I have to change it about 200,000 miles.
@mannyayala7979 Жыл бұрын
It’s looking like I may have to change mine again soon.
@esequielpinti93887 ай бұрын
Hey but you have new parts 😂 and the truck is running
@kriscalverley2131 Жыл бұрын
25 psi instant upon crank. 150 psi running. Fuel pump only provides flow to heads. Check valve in ecm plate,pull jic tip off,stretch spring clean check valve,put back in. Also make sure 2 positives and one ecm wires come off only one of 4 batteries. Always. Yup cam sensor it keeps wearing tip is a problem
@anthonycary9478 ай бұрын
2 positives and one ecm wire comes off only one battery?
@kriscalverley21318 ай бұрын
@@anthonycary947 if you have 4 batteries,always make sure ecm pos and negative comes off one battery. Otherwise you can have mystery voltage spikes and inactive codes. Had a fleet of 30 n14s. Bulket proof engine but that was the first gremlins from brand new. Once I learnt that got rid of weird little pop ups and erratic running.
@anthonycary9478 ай бұрын
Ahh makes sense. Thanks, this is the first N14 I have been around so I am just learning.
@venanciotavares1636 Жыл бұрын
Great
@vickolover4 ай бұрын
Pa lante 👍
@biggbossman1130 Жыл бұрын
My sister had a Mazda she got the timing chain replaced,after a week the car died on her. We thought it was the fuel pump also,changed it still wouldn’t start…come to find out when the shop put the timing cover back on..they pinched the wires, got one from the junk yard put it on,car fired right up
@mannyayala7979 Жыл бұрын
Crazy how the simplest thing can become a headache
@Underestimatedkid2 жыл бұрын
I have a n-14 Cummings in a 1998 international I have fuel leaking from the shut down valve I have to hold the start engine button and hit the gas to make the truck crank up would that be because my fuel pump going bad ?
@bw55592 жыл бұрын
Replace solenoid. It’s fairly cheap.
@glennihde36062 жыл бұрын
Where are you ordering your sensor from? Having a hard time finding one. Do you have a particular number?
@mannyayala79792 жыл бұрын
I don’t have the part number . Call Tri State Kenworth in Enfield CT. They will help you.
@mannyayala79792 жыл бұрын
(203) 876-5010
@mannyayala79792 жыл бұрын
I’m in Massachusetts
@chad2822 жыл бұрын
Cummins part. Go to cummins parts counter.
@lovetofly32 Жыл бұрын
Thats the first thing I changed but it didn't help.. gonna check that check valve next..
@gabrielcastro8710 Жыл бұрын
Very helpful..Did truck give you a code?? And what code?
@mannyayala7979 Жыл бұрын
I never checked for codes. Just the engine light.
@darwincruz86292 жыл бұрын
What’s the name of the sensor I just buy a truck I was running good and after two Hours driven it star giving me problems runs but turn off by it self or lost power
@darwincruz86292 жыл бұрын
The filter was from 2014 already replace but still having the same problem
@mannyayala79792 жыл бұрын
Darwin thank you for watching the video. The sensor I changed is called the positioning sensor or cam sensor. Please hit like and subscribe. Thank you
@darwincruz86292 жыл бұрын
Thanks
@axelsurvila88139 ай бұрын
Those fuel pumps for the n14 online are $475
@stowaway475 Жыл бұрын
A theirs a guy out of Ontario California he rebuilds Cummins 855 and n14 injector pumps for half the price you paid and he sends you a free return shipping label
@MrSehka77 Жыл бұрын
Name of shop or address?
@vendetta13062 жыл бұрын
Cummins dangit
@renaudinonme90372 жыл бұрын
Is it macanic or electronic
@mannyayala79792 жыл бұрын
Is what mechanic or electronic?
@GeekBoyMN Жыл бұрын
Is Cummings a division of Cummins? 😁
@Maranatha-12 жыл бұрын
Engine positioning sensor
@infohub64902 жыл бұрын
can i drive that dump truck for you😀
@jamessmith4794 Жыл бұрын
It could of been the fuel silonid to
@duvasio42042 жыл бұрын
Whoa whoa whoa fuel filter 5 months ago?? Are you ok? Change it every oil change ...
@mannyayala79792 жыл бұрын
Your absolutely right. Thanks for the reminder.
@jaygraham5407 Жыл бұрын
CUMMINGS???
@richardcornelius1050 Жыл бұрын
There is no “g” in “CUMMINS” …
@hoojang2 жыл бұрын
There is no g in Cummins.
@Martmns2 жыл бұрын
It's "CUMMINS" not "CUMMINGS" dammit!
@ronaldmicheau50862 жыл бұрын
That's mechanical n 14 if I'm not mistaken
@118chosen9 Жыл бұрын
@@ronaldmicheau5086 Any engine with an ECM is not considered a mechanical engine. An N14 is an electronic engine. You have to go back a few years from the N14 to the old 855's to be a mechanical engine. Take care!