Alan Holtham shows you how to cut a neat worktop joint using a jig and router
Пікірлер: 33
@DeanneMariaCreates Жыл бұрын
More amd more worktops are being made with Square edges, so masons mitre not required. I have just fitted my worktop. I used a new 35mm forstner bit and my circular saw set at the right depth to cut the boltholes. Cut sink and hob. Worktop joint is good and I sealed it with Unika colorfil.
@d252428q2 жыл бұрын
Outstanding video
@jonneym2 жыл бұрын
I’m just going to use a corner joint strip. I kind of find it funny how fussy people are with their kitchens in a day and age where the average person avoids traditional cooking 😀
@kevinty7 Жыл бұрын
Thank you👍🏽
@skibadeemc11 жыл бұрын
nice video but dont use those silly grip clamps if you notice at 1:20 you actully drag the jig towards you
@allyn70789 ай бұрын
He didnt clamp onto the workbench , hence why it slid.
@makolic111 жыл бұрын
HI, have you had the worktop move ? what cramps would you recommend are you a carpenter.cheers
@ANDYYSHAWW1182 жыл бұрын
Hi, why do you cut with a jig saw before using a router for the male cut please? I'm about to do my own worktops
@1petrofski2 жыл бұрын
To remove the bulk of the chipboard otherwise too much routing is required
@TheWorstCSGOPlayer12 жыл бұрын
Hi Alan, are those jigs commercially availible? Where would one find one of these?
@julianreverse6 жыл бұрын
Can you read?
@supersesqui11 жыл бұрын
Lots of very important details missed from this video.
@ahmedaljubori613710 жыл бұрын
لطيف جدا
@vladd54253 жыл бұрын
i had some nice maccers breakfast
@duck-re9ts2 жыл бұрын
Biscuit machine make biscuit on the top ,not left side
@olliejames2899 Жыл бұрын
😂😂 mr george
@Umairthatguy2 ай бұрын
No need these all work just put joint strip that s it
@acewelding8 жыл бұрын
When he positions the jig to make the female cut, he doesn't take any notice of the width of the what will be the male cut.
@cassiya1008 жыл бұрын
Haha. I noticed that too?
@outsidethepyramid7 жыл бұрын
you are wrong. actually the interchangeable spacers ensured it was positioned correctly.
@acewelding7 жыл бұрын
Colonel Walter E. Kurtz The work tops vary in width, if you use the stops on the jig you don't end up with the back edges exactly flush, that's why you should cut the male cut first and mark the width of the worktop on the jig to line it up with the edge for the female cut. It's more exact than using a spacer, or anal.
@outsidethepyramid7 жыл бұрын
acewelding thanks for the reply. my worktop were delivered yesterday so im after all the tips i can get. wisdom of the crowd and all.
@acewelding7 жыл бұрын
Colonel Walter E. Kurtz I wish you every success, you tube's brilliant for tutorials. Who dares wins 👍
@vru10124 жыл бұрын
Poor cut
@BestUserNameUK7 жыл бұрын
Cowboy!
@roythebuilder10 жыл бұрын
It would be impossible for someone to do a worktop joint by following this vid, It is a waste of time. I.E wahat if the walls are out of true ? this vid is a waste of bandwidth
@arlingtonworksurfaces17407 жыл бұрын
Quite an old video, but frankly I am disappointed. Its not something one can follow and replicate easily and now that most people have pointed out flaws in the comments prior to mine, we do not intend to follow it either.
@tigereye12088 жыл бұрын
This is a terrible example. Worktops cost a lot of money yet you have a video showing the jig moving when being routered at 1:20. This would effectively make the worktop fucked.
@Aztech738 жыл бұрын
Is moving all togheter with the worktop
@paullamb76974 жыл бұрын
DONT FOLLOW WHAT HE SAYS, ITS ALL WRONG
@c.m.40783 жыл бұрын
No really. Why it's all wrong?
@starkaran83903 жыл бұрын
I did something like this a month ago with plans from Stodoys.