This is the next thing on the 12 valve to do list and probably the best video I’ve found on it and I’m a firm believer that if you can follow instructions you can do anything even rocket science 😂 appreciate ya Rob
@CUTTERUPROB11 ай бұрын
thanks brother
@ed47092 жыл бұрын
Will be doing this job on my 97 dodge and checking my new Recon 12v before installation. I appreciate the tutorial bud! Awesome work as always. 👍🏼
@robkatzor1324 Жыл бұрын
awesome explanation of order of adjustment!
@erneumann31362 жыл бұрын
Good job Rob!
@elroyelblander62772 жыл бұрын
The VP44, there's actually a line on the gear that lines up with the cover marker.....at that location,the woodruff key is at the 6:00 position...so to remove the pump ,you want the key at 12:00 so the key doesn't fall out..which is actually not exactly tdc #1 compression....I believe...but anyway.. 👍👍
@CUTTERUPROB2 жыл бұрын
You could be right. Been a while since I did one.
@elroyelblander62772 жыл бұрын
@@CUTTERUPROB👍👍yeah,it don't matter man I just had one apart recently to replace the gear case gasket and swapped in that Hamilton cam and all...😆,so it's still a little fresh ..but anyway 👍👍
@CUTTERUPROB2 жыл бұрын
I added the info to the description
@Steve-cy4rv6 ай бұрын
Good explanation, have you ever ran into a problem, where one or two of the pushrods are extended up higher than the rest? I’m rebuilding my 12 valve and I ran into this problem and no one can answer it, I’m wondering if you can. Thanks in advance
@CUTTERUPROB6 ай бұрын
Like the push rods are longer than the others ? If that’s the case I would say the couple of them are the wrong style
@elroyelblander62772 жыл бұрын
Evening feller 👍🍺👊
@reitzy692 жыл бұрын
So my 97 12v has 92k on it...should it be done soon? And its not been done ever and when should it be done
@CUTTERUPROB2 жыл бұрын
Not a bad idea to check
@reitzy692 жыл бұрын
@@CUTTERUPROB alright I will do that the next day im off work...and how often then should I check it? Every 50k or so?
@witcher712 жыл бұрын
@@reitzy69 100k
@matt98eclipse Жыл бұрын
What about setting valve lash on a brand new fresh common rail short block? Say you install head and loose cylinder 1 TDC before setting valve lash??
@CUTTERUPROB Жыл бұрын
If it’s fresh engine you will have to loosen the rockers most the time. But same as I do it on a 12v
@zachw96572 жыл бұрын
what did you use for paint?
@CUTTERUPROB2 жыл бұрын
It’s wurth brand enamel
@Banjoandguns2 жыл бұрын
Doesn’t the crank turn clock wise
@CUTTERUPROB2 жыл бұрын
When running yes. But doing this it doesn’t matter the direction you turn it. I have tried it both ways to see if it made a difference.
@yoangelquinterohernandez8463 Жыл бұрын
Hola no tienen trduccion en español
@Yacht-tech10 ай бұрын
You don’t explain how do you know when the first cylinder is at top dead center you can put it on top dead center but it could be on any cylinder top dead center should’ve explained that as well
@CUTTERUPROB10 ай бұрын
the first minute half thats what i am talking about