Cutting a Hole in the Floor | RWD GTI | Pt 2

  Рет қаралды 178,882

Deutsche Auto Parts

Deutsche Auto Parts

Күн бұрын

In today's video, we continue to push towards a RWD GTI!
We weigh aluminum, steel, FWD, and AWD Subframes to compare the weight differences. In addition, we have to figure out how to wire our existing TTRS fuel Pump to work on the new AWD gas tank. To get our new R32 subframe installed on the car, we have to first make some modifications, including cutting a hole for the secondary fuel pump and cutting an even bigger hole in the trunk so the subframe can fit under the car. We also installed some awesome 034 performance parts to our subframe! Links below!
Links Talked about in this video
Faux Wheel Drive Tshirt (Limited Run)
www.shopdap.co...
MK5 RWD Build Part 1
• Can we make a RWD Volk...
Wolf Auto Parts
wolfautoparts....
Spherical Rear Trailing Arm Kit, MkV/MkVI Volkswagen Golf/Jetta/GTI/R & 8J/8P Audi A3/S3/RS3/TT/TTS/TTRS
www.shopdap.co...
Density Line Adjustable Rear Toe Link, MkV/MkVI Volkswagen Golf/Jetta/GTI/GLI/Rabbit/Golf R & 8J/8P Audi TT/A3
www.shopdap.co...
Rear Subframe Mount Insert Kit, 8J/8P Audi TT/TTS/TTRS & A3/S3/RS3 Quattro, MkV/MkVI Volkswagen R32 & Golf R
www.shopdap.co...
2.0t TSI and FSI Upgraded Fuel Pump and Module DIY
• 2.0t TSI and FSI Upgra...
TTRS Fuel Pump and Startup | Project MK5 Ep 9
• TTRS Fuel Pump and Sta...
PM4 Fuel Pump Control Module Install | Project MK5
• Video
----------------------------------------------------
Shop for VW and Audi Parts Here
shopdap.com
VW AUDI Specialty Repair Cornelius NC
www.daprepair....
VW AUDI Specialty Repair Kent Ohio
www.daprepair....
More info on DAP Reward Credit
shopdap.com/st...

Пікірлер: 144
@Deutscheautoparts
@Deutscheautoparts 3 жыл бұрын
Part 1 - kzbin.info/www/bejne/ZqPRXq2Va9Bmp5o Part 3 - kzbin.info/www/bejne/ianRpYyqbL59jdE Part 4 - kzbin.info/www/bejne/e3SzmmSggt2Bd6M Faux Wheel Drive Tshirt (Limited Run) - www.shopdap.com/dap-faux-wheel-drive-tee.html
@kylereese4822
@kylereese4822 3 жыл бұрын
Small Tesla S or X or model 3 rear motor modified for single output. diff close to where rad used to be, motor near firewall passenger side, connected to prop shaft or you may even get 1 - 2 overdrives in the drive line too giving you a 2 speed transmission similar to the Zombie 222 Mustang...
@cd155mx
@cd155mx 3 жыл бұрын
This is the best reality show of all time!!
@alessandropru
@alessandropru 3 жыл бұрын
So good. Reminds me of OCC drama, but Junkyard Wars awesomeness
@demonkiller3418
@demonkiller3418 3 жыл бұрын
Everyone on the VW forums would be like "iTs ChEapEr To bUy a RwD cAr iNsTEad"
@SuperLbptutorials
@SuperLbptutorials 3 жыл бұрын
It is, but that's not the point is it?
@shona5512
@shona5512 2 жыл бұрын
Oof. This brings me back. Literally every time you try to do something creative, just purely for the fun of it, everyone tries to deter you from it. You can make it blatantly clear that you know it's absurd and it will cost money, but you're willing to do it for the novelty and they'll STILL try to argue that it shouldn't be done rather than just help with whatever you might need.
@a20axf
@a20axf Жыл бұрын
@@shona5512ahhh, the forum life… yep pretty much sums it up.
@NedNew
@NedNew 3 жыл бұрын
Did you know that the differential can be mounted on a sub-assembly (made by Bosch) and then angled at 270 degrees to make room for the drive shaft? It allows about 40mm of extra space and would mean a lot less work. The sub-assembly is only about 3kg and costs 25 euros.
@lutherblissett9070
@lutherblissett9070 3 жыл бұрын
Do you have a part number for this sub-assembly?
@rajeshdookaran7741
@rajeshdookaran7741 2 жыл бұрын
@@lutherblissett9070 👍
@tanovw
@tanovw 3 жыл бұрын
Love this build already
@mattyc2815
@mattyc2815 3 жыл бұрын
there's this new invention called a jigsaw that's really good at cutting through metal...instead of drilling a million holes.
@666litium
@666litium 3 жыл бұрын
or at least a side cutting drill bit for steel
@MotorHeadTech
@MotorHeadTech 3 жыл бұрын
I'm learning soo much thank you! This is definitly going to help with my crazy Frankenstein 2013 Audi A4 build soon to be 500hp on the 2.0t
@AL_145
@AL_145 3 жыл бұрын
29:02 Paul "if you only knew how bad things really are"
@YouTubeHandlesAreStupid
@YouTubeHandlesAreStupid 3 жыл бұрын
I know, that face lol
@austinregister990
@austinregister990 3 жыл бұрын
lol I love how u can watch Paul slowly getting more and more demoralized by all the hurdles that cost time
@Osprey1994
@Osprey1994 3 жыл бұрын
Dude this is such a good Christmas present...thank you.
@lazartsaprev2580
@lazartsaprev2580 3 жыл бұрын
The greatest series for WAG on the internet! RESPECT
@gilmello8296
@gilmello8296 3 жыл бұрын
So we get a VW ad in the middle of the video for a car that we can’t buy in the states. VW, why do you do this to us😂
@matthewross2236
@matthewross2236 3 жыл бұрын
I feel a lot of "why the F are we doing this again?" vibe in this video hhaaha
@JohnWickOG
@JohnWickOG Жыл бұрын
You guys are hilarious, im supporting the channel and business just bc of that!
@jheyhey39
@jheyhey39 3 жыл бұрын
This is such a good series of videos. Thanks for making these!
@jw18xxx
@jw18xxx 3 жыл бұрын
Been here nearly since your beginning. I linger, but if you keep this path up you guys are on to something here. Very unique and I see you guys going far very soon. Noticed trends like this with KZbin such as Cleetus and his crew, Marty and Moog, Thomas and James and a few others. You guys make great content together. Keep up the great work👍
@rajeshdookaran7741
@rajeshdookaran7741 2 жыл бұрын
I love builds and rebuilds, especially the restoration and cleaning of parts, 👍Big up, well done guys
@160calories
@160calories 3 жыл бұрын
Humblemechanic “these guys are the German auto parts experts” DAP: *hold my beer* Lmao this series is awesome so far
@SKYRIDR
@SKYRIDR 3 жыл бұрын
Amazing work and video. Cant wait to see the rest. Any plans on figuring out how to put a golf R drive train into a 2 door GTI and making a 2 door golf R? A MK7 2 door golf r that is!
@ALLTHINGSCINEMA24
@ALLTHINGSCINEMA24 3 жыл бұрын
11:28 mission failed cracked me up
@JoeyTRS3
@JoeyTRS3 3 жыл бұрын
It’s not fair how they get to have all the fun 😄
@frederichartell7390
@frederichartell7390 3 жыл бұрын
Think it's time for a plasma cutter!
@peterfakhri7574
@peterfakhri7574 3 жыл бұрын
love your editing and double entendres. too funny. great work.
@dildoshwaggins1017
@dildoshwaggins1017 3 жыл бұрын
BEST CONTENT ON KZbin SO FAR
@MuchoBoosto7
@MuchoBoosto7 3 жыл бұрын
This series so far has had me cracking up, love the format and humor between you guys, keep it up!
@rossbowman202
@rossbowman202 3 жыл бұрын
This series is great! Stellar work gentlemen.
@yeahitskimmel
@yeahitskimmel 2 жыл бұрын
Max has Adam LZ's exact same voice. Have been listening to this series and keep thinking the video must've changed
@matthewstyer5587
@matthewstyer5587 3 жыл бұрын
A jigsaw with metal blade is perfect for cutting up to 6mm with no sparks
@AndreyKalugin_53rus
@AndreyKalugin_53rus 3 жыл бұрын
Hello from Russia. Well done, great job!
@Jude3e
@Jude3e 3 жыл бұрын
7:05 "hey" So paul's wife is real... I figured it was just Charles from humble mechanic always calling and texting and paul was just pretending.
@Deutscheautoparts
@Deutscheautoparts 3 жыл бұрын
He’s the mistress
@thevuntzer
@thevuntzer 3 жыл бұрын
The MGS ! got me good. Love your channel.
@snoopdaclown
@snoopdaclown 3 жыл бұрын
Co motorsports can help but you prolly have it all done. They can sell you a piece to weld in the trunk.and they can tell you what all needs cut to fit
@GTI-Eddy
@GTI-Eddy 3 жыл бұрын
You can fit the fuel transfer from facelift S3, or mk6 Golf R and that has the 'daddy' connection to suit the TTRS pump. That is what I did with my 4wd converted GTI
@aroundomaha
@aroundomaha 3 жыл бұрын
Entertaining and informative! Lot of fun to follow.
@WreckedRevival
@WreckedRevival 3 жыл бұрын
9:28 they make jig saws for that sorta thing ;) I believe my fab/tool knowledge and wrench time may be at least somewhat useful when you guys do things like this, if hiring another tech is feasible anyway lol.
@jackham2549
@jackham2549 3 жыл бұрын
Another good video. I didn’t know it only took about 1-2hours to make a GTI RWD, I might have to do some work over the holidays here
@rkan2
@rkan2 3 жыл бұрын
Replaces the bushings of subframe AND then cuts a massive whole in to the monocoque it is held in... :D
@MrEverretto
@MrEverretto 3 жыл бұрын
Those cuts are fucking gold man. Good job on this series
@MREVREN
@MREVREN 3 жыл бұрын
Just found this channel, this is great 👍👌👌👌👌
@Danielprokopij
@Danielprokopij 3 жыл бұрын
Paul looks like he regrets offering to help every step of the way 😂🤣
@einfelder8262
@einfelder8262 3 жыл бұрын
16:56 don't adjust the ends, adjust the middle. It's a turnbuckle adjuster.
@lachdawg
@lachdawg 3 жыл бұрын
i love when people only adjust one end out, then i tell them they installed it wrong and its not my problem.
@dethsyndrome
@dethsyndrome 3 жыл бұрын
I to want to do a fwd to awd conversion but on my mazda 6s. Theres so much to learn.
@antesemitere
@antesemitere Жыл бұрын
look at us forgeting Jigsaws have metal cutting blades lol
@jaydelledonne
@jaydelledonne 3 жыл бұрын
just realised how lucky i was that i didnt try the passat rsf in my gli lol, also very happy the gli's dont need to cut out the spare tire well
@dantem306
@dantem306 3 жыл бұрын
Day 2 of being here every day until it's complete!
@ArminVBThe1
@ArminVBThe1 3 жыл бұрын
best series on yt, hope it takes at least 20 episodes (JK), looking fwd to the next ones
@Vardetettvalhelatiden
@Vardetettvalhelatiden 3 жыл бұрын
Majestic video series
@bagelbandit6076
@bagelbandit6076 3 жыл бұрын
*T-shirt idea* *Back* See you another day *Front* It’s another day
@DevineDigital
@DevineDigital 3 жыл бұрын
The passat one doesn't fit, ask me how I know. The haldex front bracket is about 1 inch forward compared to the golf, and it hits the frame and tank because of it. EDIT: apparently I should watch the entire video before commenting my experiences, haha.
@cmirwin
@cmirwin 3 жыл бұрын
Love the wrestling references! WOOOOOO!
@aronbennett4760
@aronbennett4760 3 жыл бұрын
I'm loving this series. Fuck what they say, take the long way. I may have to buy another TT to go drifting.
@korni92
@korni92 3 жыл бұрын
Older A3 8P and the TT 8j has the alu subframe too. Also the TT has Passat alu bearing housing. There are also smaller ones made from alu from s3 and rs3. But the complete trunk bottom is different between awd and fwd.
@bradleystaruski9881
@bradleystaruski9881 3 жыл бұрын
6:42 nice action shot with no battery in the impact
@mattyc2815
@mattyc2815 3 жыл бұрын
Love this build!!!!
@bertchalmers
@bertchalmers 3 жыл бұрын
Why is that rear bumper still on???? Are you masochistic?
@rzorNvme
@rzorNvme 3 жыл бұрын
A rear wheel drive pocket rocket
@tuckerlutz8765
@tuckerlutz8765 3 жыл бұрын
@6:40 that impact didnt even have a battery on it 😂
@Atrociousa3
@Atrociousa3 3 жыл бұрын
Y’all should sell that plate you make. I sure could use one. Maybe one that gets bolted into place for servicing the haldex
@bumzua69
@bumzua69 3 жыл бұрын
Who else gets “the office” vibes from these guys 🤣🤣🤣
@michaelw6277
@michaelw6277 3 жыл бұрын
I kind of want to drive up from Atlanta to hang out and learn some new dad jokes.
@TheMano33
@TheMano33 3 жыл бұрын
You guys have more puns than a Family Guy episode. Love it
@viktormarchenko3394
@viktormarchenko3394 3 жыл бұрын
Жаль не все понятно , только зрительно , но вы классные и класс идеи. Удачи
@audiemblems
@audiemblems 3 жыл бұрын
Никогда не поздно выучить новый язык)) здесь 25% важности составляют тексты и разговоры)
@YouTubeHandlesAreStupid
@YouTubeHandlesAreStupid 3 жыл бұрын
This content is not only great; but, hilarious. You should probably break these days up into multiple vids; but, I'm no KZbin clickbaity expert. And hey, my favorite part is when you run a lot of safety risks and put your body or another person in jeopardy... I'm into this, so keep it up! I also like the look Paul gives when his spirit looks broken.
@donnys2965
@donnys2965 3 жыл бұрын
When removing the rear tire section was there a black filter like “thing” wrapped around? Also what is that? It’s has three hoses that leave and enter the black drum. Also hi, love the frequency of the videos. Hype!
@nimanazarinia3662
@nimanazarinia3662 3 жыл бұрын
keep going
@tymac3306
@tymac3306 3 жыл бұрын
Hardcore dub luv
@chrisrutherford3862
@chrisrutherford3862 3 жыл бұрын
Bevel box The weak link that whats my money on
@ChrisMadson
@ChrisMadson 3 жыл бұрын
Since the front diff is before the bevel gear, won’t removing the front axles still just put all the power to the front wheels even if the Haldex is locked... likely just spinning the front left wheel? This may be able to be solved by putting a spool in place of the front diff or just welding it (and balancing)
@richardhunt1384
@richardhunt1384 3 жыл бұрын
I know this gonna sounds a bit 💩y but why not just put your uprated/ upgraded engine from the GTI into an R32 and then modify the R32 to RWD??? 🤔🤔 Great videos guys!!! 😁😁👍👍
@miguelsanchez6465
@miguelsanchez6465 3 жыл бұрын
I’m shocked at how soft all the bushings are on a r32! I’m definitely changing all my bushes this winter, I have the same stock trailing arms and that side to side play is gross!
@KrustyPickles
@KrustyPickles 3 жыл бұрын
Would it not have been easier to hang the sub frame first then assemble it?
@ShayneTMBR
@ShayneTMBR Жыл бұрын
Now watching this in 2023
@cse5975
@cse5975 3 жыл бұрын
Well. The hole makes it easier to get diff on. Normally diff has to go on subframe first then in the car.
@rzorNvme
@rzorNvme 3 жыл бұрын
WWF brothers
@Shadowband72
@Shadowband72 3 жыл бұрын
The boy's over at Throttle have been attempting do rear wheel swap a Civic , for what seems like a year or more . Looks like they should have started with a VW instead .
@schmeebo8753
@schmeebo8753 3 жыл бұрын
love this series. what are the wheels you guys put on the gti? they look awesome
@mikemocon8582
@mikemocon8582 11 ай бұрын
Here's an idea, move the gas tank
@jonnyboy2504
@jonnyboy2504 3 жыл бұрын
No flex zone 😅
@xxtrengt8871
@xxtrengt8871 3 жыл бұрын
Great stuff, love the memes ! You guys seem to be having a great time, this is what makes me wan't to watch even more.
@zoomer1468
@zoomer1468 3 жыл бұрын
I want it N O W
@adellisdevelopmen6593
@adellisdevelopmen6593 4 ай бұрын
an R32 early pre 2006 has aluminium subframe (could be late i forget which) and audi s3 8p have aluminium rear subframes dont know if you have them as couldnt see the other golf v r32 has ally rear spindles (knuckles hu s whatever you americans call them) s3 8p have also front alloy spindles
@eyesharp
@eyesharp 3 жыл бұрын
That alu subframe came stock in both of my r32 mk5s. An 06 and a 07, I thought that was the stock one...
@wiwii3976
@wiwii3976 3 жыл бұрын
Hi, did you re-use the same rear coilovers??
@antionefoster5844
@antionefoster5844 Жыл бұрын
Bro started blasting 💀
@kaese2002
@kaese2002 3 жыл бұрын
a limited german registration plate from 2009?
@iMoriMori
@iMoriMori 3 жыл бұрын
Time to unpimp der fuel tank
@keith_167
@keith_167 3 жыл бұрын
Isn't it a better option to swap an R32 engine to a EA113 with the AWD?
@spinnetti
@spinnetti 3 жыл бұрын
Little confused... won't this just be a R with no front drive?
@brandonanderson4999
@brandonanderson4999 3 жыл бұрын
Could you have just used a large mallet to clear the Passat subframe to body?
@Deutscheautoparts
@Deutscheautoparts 3 жыл бұрын
With enough pounding anything is possible....
@cedriccox1001
@cedriccox1001 3 жыл бұрын
@@Deutscheautoparts you'd be surprised how many times I use this in my life!!!
@runawaytowtruck
@runawaytowtruck 3 жыл бұрын
Should have used a Audi A3 subframe
@gar1c440
@gar1c440 3 жыл бұрын
How much money for something like that for cars 2010-2011?
@carlmcrobcustomgoldsmith11
@carlmcrobcustomgoldsmith11 3 жыл бұрын
Rwd swapping a golf....the education we want.....Non stop quotes with clips to back them up....the education we need. What’s the Scenario?!
@Jamk14
@Jamk14 3 жыл бұрын
U guys going to euro tripper???
@alexisdown408
@alexisdown408 3 жыл бұрын
If you guys don't want that exhaust anymore I'll by it, give me some contact info and we can talk about it
@jahndolo
@jahndolo 3 жыл бұрын
why not use the boot pan off the r32? Was it damaged?
@Deutscheautoparts
@Deutscheautoparts 3 жыл бұрын
Yup crushed
@jahndolo
@jahndolo 3 жыл бұрын
@@Deutscheautoparts anyway, amazing content! waiting on the next episode!
@fredgasburger5969
@fredgasburger5969 3 жыл бұрын
A 3D printer would be nice to have.
@joshuam7552
@joshuam7552 3 жыл бұрын
22:50 hahahahahahah!!
@miguelsanchez6465
@miguelsanchez6465 3 жыл бұрын
Isn’t the rear diff only designed to handle half the power of the engine?
@Deutscheautoparts
@Deutscheautoparts 3 жыл бұрын
Yup
@damianc1043
@damianc1043 3 жыл бұрын
😅 do you guys have a Manual NBL 6speed transmission for a Mk7 GTI
@tzepuh
@tzepuh 3 жыл бұрын
RWD on FWD car... You want to have your rear end as heavy as possible... :)
Welding our Haldex Diff for RWD | Pt 3
30:00
Deutsche Auto Parts
Рет қаралды 181 М.
Will our RWD GTI do Donuts? | Finale
26:02
Deutsche Auto Parts
Рет қаралды 364 М.
Angry Sigma Dog 🤣🤣 Aayush #momson #memes #funny #comedy
00:16
ASquare Crew
Рет қаралды 49 МЛН
How Strong is Tin Foil? 💪
00:26
Preston
Рет қаралды 37 МЛН
МЕБЕЛЬ ВЫДАСТ СОТРУДНИКАМ ПОЛИЦИИ ТАБЕЛЬНУЮ МЕБЕЛЬ
00:20
RWD Converted Volkswagen GTI (With a BMW V8!) is the Ripper We Didn't Know We Needed
12:14
Hoonigan Daily Transmission
Рет қаралды 417 М.
How Bad is our Cheap R32?
22:53
Deutsche Auto Parts
Рет қаралды 343 М.
He's Addicted to Saving R32s | Owner Spotlight
15:52
Deutsche Auto Parts
Рет қаралды 78 М.
VW Golf MK1 with BMW M50 Turbo *350HP RWD*
11:43
Twin Engine Corsa
Рет қаралды 59 М.
What it Takes to Build a RWD VW Golf
10:01
Donut
Рет қаралды 1,4 МЛН
COMPLETELY Fixing a TRASHED MK5 GTI ~ Worth It?
32:54
HumbleMechanic
Рет қаралды 373 М.
Converting the AUDI DRIFT CAR TO RWD & Welding The DIFF!
15:59
We make a VW VR6 Engine Rear-Wheel Drive on Scotto’s Gymkhana GRiD Toyota AE8
25:14