Response to • VFC MP5's - What Could... TL;DW solder on the brush holder melted and smoked, gun still fully functional after 2 minutes of semi.
Пікірлер: 54
@kritas94323 жыл бұрын
Drop in a Brushless Motor and then never have issues again!
@michaelmccr32945 ай бұрын
Mate your aeg is fully upgraded to the teeth..... negative was making a point as it being stock and yes asters, titans and sometime peruns do burn out if your going happy binary fingering mode and that is fact.
@s989582 жыл бұрын
Nice test. How many amps can a Titan take? (heavy DMR setup, mostly semi)
@kewldude0072 жыл бұрын
it will protect itself before it fails physically like a cyma etu, I dont know that thermal or amperage limit though.
@jacobjstoffer4 жыл бұрын
nice
@nielsvanderwaa95394 жыл бұрын
Doesn't 40% draw to much on this setup? Ss 1 more tooth would be plenty right?
@nielsvanderwaa95394 жыл бұрын
Also, that smoke is probably the brushes being pushed very hard by the AB.
@kewldude0074 жыл бұрын
active brake does not use extra power, and no, its the same smoke the etu made
@Servalman8724 жыл бұрын
@@nielsvanderwaa9539 The smoke is from the cheap/dirty solder cyma used melting/burning off. I was able to melt it with a heat gun.
@fastbysal87974 жыл бұрын
@@kewldude007 anytime the motor is running it's drawing amps..
@kewldude0074 жыл бұрын
@@fastbysal8797 You dont know how active brake works
@fastbysal87974 жыл бұрын
And what's the point of this video? Wasn't the original argument over the factory mosfet burning under a 11.1? Not trying to be "that" guy, just a clarification
@darkshock42mlg054 жыл бұрын
Negative said you can blow a titab the same way by trigger spamming on 11.1 for 1 minute straight. Not that anyone would try to do that either way. Im actually surprised that the thing it's supposed to do actually killed it. To be fair negetive tested the 1 minute of semi auto multiple times on a 7.4.
@fastbysal87974 жыл бұрын
@@darkshock42mlg05 I had seen that video too...I own one...I run a 11.1 titan. No issues yet. Did have issues with tons of grease in the mid caps I bought
@beanos22872 жыл бұрын
Why does this battery seem to damage these guns? I've heard that using large 11.1 lipos is no problem since the gun only draws what it needs, so why are these guns going up in smoke even when using such high end ETUs? Does it have to do with the build being very high stress?
@kewldude0072 жыл бұрын
the smoke in this video is from the motor have shitty solder on the brush connections and it melting
@beanos22872 жыл бұрын
@@kewldude007 ah, gotcha. So I shouldn't have this problem using an SHS High Torque and a Perun V2 Hybrid.
@beanos22872 жыл бұрын
@@kewldude007 btw the battery I'm using is a 5200mah 80c 11.1
@darkshock42mlg052 жыл бұрын
@@kewldude007 so basically you need a warhead to use a really big battery. Warhead makes brushless motors. If i made enough to do that count me in. Also you probay sholdnr be using this battery if its glimg to cause smoke to come out of your gun. It doesn't seem safe.
@kewldude0072 жыл бұрын
@@darkshock42mlg05 warheads did not exist when I made this video
@darkshock42mlg05 Жыл бұрын
Whata battery is this. It looks gigantic.
@mehdib48713 жыл бұрын
Hello mate! i just bought a cm097A and after a 30s suppression shot on semi (7.4v) it keeps shooting even when i dont pull the trigger. do you know if this could be fried mosfet? + do you recommend getting a SHS Motor instead of the stock one? Thanks for the vids, it helps a lot
@kewldude0073 жыл бұрын
fried fet, keep the stock motor
@mehdib48713 жыл бұрын
@@kewldude007 thanks mate 👍 I hope I'll be able to install a Gate by myself, else I will call a tech 👍
@AlikKhryu3 жыл бұрын
link for the battery?
@jaketrotter54233 жыл бұрын
So... I asked about the Krytac or the CYMA Plat M4 earlier, I found a Krytac Trident Mk2 SPR for like $270 ish dollars, then there’s the CYMA and it’s impossible to find a used one (is that because no one sells theirs or they are not commonly bought?), also I have found a Custom build Gemtech VFC Avalon series for $275. Which one do you think I should choose and could you answer some of those questions? I know I have asked a lot but I want a gun that I will be happy with
@kewldude0073 жыл бұрын
the cymas arent very common yet. krytac if you never plan on changing the internals, vfc if you do
@jaketrotter54233 жыл бұрын
@@kewldude007 could I get your email so I could show you the Avalalon?
@jaketrotter54233 жыл бұрын
@@kewldude007 and I want to change internals, but I am new to airsoft so I will need help on how to do each thing
@kewldude0073 жыл бұрын
@@jaketrotter5423 no
@jaketrotter54233 жыл бұрын
@@kewldude007 ok... well could I tell you what the gun has in it? Like internals
@LMSxReZzoRHD2 жыл бұрын
does it fit in the gearbox without modifying anything???
@kewldude0072 жыл бұрын
no, watch my video on the install
@knightairsoftwarrior2 жыл бұрын
Did you keep the safety bar inside?
@kewldude0072 жыл бұрын
no
@knightairsoftwarrior2 жыл бұрын
@@kewldude007 thanks, i got the basic titan too plan on buying the advanced software for I was wondering if its worth the upgrade
@knightairsoftwarrior2 жыл бұрын
Would you happen to know any good after market triggers that aren’t short in length for mp5?
@kewldude0072 жыл бұрын
@@knightairsoftwarrior I do not
@Facewizard134 жыл бұрын
I want to know what happens next!
@kewldude0074 жыл бұрын
motor died
@Buster12763 жыл бұрын
@@kewldude007 but why? I don’t fallow I want to make it dsg but don’t know how.
@kewldude0073 жыл бұрын
@@Buster1276 magnets got too hot and degraded them, the wire into one of the brushes broke off. under normal use this should not happen
@Buster12763 жыл бұрын
@@kewldude007 umm can I throw in a 11.1 lipo stick average and will this shoot fast and be snappy?
@setsuna2004 жыл бұрын
How about we do this to a g&g mosfet?
@kewldude0074 жыл бұрын
im not buying a g&g
@thefancyllama46573 жыл бұрын
@@kewldude007 whats wrong with g&g
@ogfartmasta74803 жыл бұрын
@@thefancyllama4657 everything
@chrisapolinar11022 жыл бұрын
@@ogfartmasta7480 My G&G sbr 308 with the G2H gearbox would highly disagree...... shoots 385fps with .25g and 26rps with a titan 11.1 3000mah 16c, only mods in the gearbox are a stainless full cylinder and a Laylax POM piston head. Over 15k rounds though is so far.