HOW TO BUILD YOUR OWN RETURN FUEL SYSTEM FOR 11-17 MUSTANG GT

[@GearHead704]

Looks like you were smart to build your own fuel system, especially with all the $$ you saved. Great to meet you this weekend Darryl!

[@DNMCSPD]

Great work! I believe if you piece a whole kit together with instructions and sell it, you would do very well. I would entertain a set.

[@aimless-drifter]

very good content, love seeing video like this. You've motioned that you have a MAP sensor is that just for measuring boost, do you also have MAF sensor for measuring Air or are you running off MAP sensor alone?

[@BOSS-jf7on]

You do good work, thanks for sharing the details.

[@d3et1roi3t]

How did this fuel system end up working? No issues? Still going? Failed? What would you change now that you've had this for a while

[@Micah-Thor]

Can you make a video of how you hooked up your vacuum lines for your boost controller! I have the top mount on3 kit and haven’t found much info out there about this

[@notacoyote2790]

How did you do your relays in the trunk and what size wire did you run to them? I’m gonna make a similar fuel system for my car and I’m trying to figure out what the best way to do it is. Also did you have to put a jumper wire in the fuel control module connectors for the way that you did this wiring?

[@mfjones2217]

What is white/brown stripe wire or white/purple stripe, not Shure if it's purple or brown , u got 2 sending wires a yellow/grey fpdm trigger and a white one beside the yellow before sender wires, what the F' does the white/brn wire do on OEM hat, is it a ground , I'm coyote swapping and using factory harness 14gt, but old metal hanger, should I ground pump to hanger or is it white wire

[@minkydo97]

Could you drop a parts list with where you got everything? I’m looking to build my own too!!!

[@anthonycampbell5504]

Great work! Great videos! Do you remember about how much you spent all together on the fuel system your installing?

[@miguelperez1437]

Hello! I noticed u used 2 180 fitting and 2 couplers in the front of the rails, are all these fitting 8 AN size? I’m trying to do my return lines

[@koron274]

I have the on3 relay box and it has 3 lines that are suppose to connect to a 12v switch. Can connect all 3 to the yellow and brown line?

[@5.0bsessed]

What's the parts list?

[@caseylemons6363]

Was curious if you had the remote start an if so did you retain it with the triple hat system

[@Wengerdperformance]

My car did not come with remote start

[@caseylemons6363]

@@Wengerdperformance I fixed it lol thanks again your vids are very helpful !

[@NWIPerformance]

How many ft of hose did you buy of the 10an and 8an?

[@Wengerdperformance]

20 of each

[@MarioSanchez-qx6yn]

Good setup, better than forcing a pump to do more work out of its efficient zone i.e. boost.a.pump. why not a single high volume external pump?

[@Wengerdperformance]

I'm not pushing the hp to require one of those

[@mikeorgeron3296]

What brand is the fuel hat you used?

[@jsimmonstx]

That's an On-3 hat. Everybody pretty much agrees it's a piece of shit. The Fore Innovations hat is much nicer, and doesn't require JB Weld to seal the wiring harness. I'm all about saving money where possible, but this is not an area that you should be doing that.

[@kgbonee1]

Regulator mounted to the firewall will not pass nhra tech

[@Wengerdperformance]

I know numerous guys with it on there passing

[@NickelWhiteS550]

Support your local youtuber. Speedaddict731.

[@freddiew2242]

Wiring on the hobbs switch?

[@Wengerdperformance]

Yup

[@freddiew2242]

@@Wengerdperformance how did you do the wiring on the 2 wires from the hobs

[@Wengerdperformance]

@@freddiew2242 I have a single hobbs switch which has 2 wires. 1 wire gets power the other goes to the relay that will activate your 3rd pump. X boost pressure activates the hobbs switch which activates the relay and turns on the pump

[@miguelperez1437]

Boosted Coyote Hello! I noticed u used 2 180 fitting and 2 couplers in the front of the rails, are all these fitting 8 AN size? I’m trying to do my return lines

[@freedom6919741]

Looks complicated

[@On_3]

Not really