DD RIS II FSB Hao To Install

[@jwhiskey534]

Bruh the outro💀you’re a man of culture I see.. subscribed

[@Vane_M4A1]

Touhou and Block II in the thumbnail?? There was no way I wasn't gonna click

[@blackcloudr1130]

Just a heads up you don’t need locktite that yellow is a thread locker and on the flat heads that white washer is so it locks in place I’ve had a ris 2 rail for almost 10 years and never had one even attempt to work loose, great video btw

[@ProudFudd]

The DD SOCOM profile barrel is only* available when you buy one of the Brownell's special uppers with the brown rail.

[@2392F]

As a PSA: The LMT barrel will most likely not work. I tried one of their barrels with a preinstalled FSB and it was installed with press fit straight pins, NOT taper pins. The pins wouldn't budge and I had to get a different barrel.

[@sr25jd]

What did you torque the barrel nut to ??or did I miss something Thanks I ordered one and found this Video …hope my barrel and DD M4A1FSP ,goes on like this one did .. GodBlessYou and ThankYou again

[@j.james-88]

@55 ft/ibs.

[@ms542]

Did you use a torque wrench/screwdriver on the handguard flange screws? I cannot find one that will fit and wondering if it's absolutely necessary. I didn't know if you could just hand tighten then give it a 1/4 - 1/2 a turn more.

[@jojomasterson4852]

I just hand tightened it then gave it like a 1/4 turn. If you want to use a torque wrench to ensure everything is to spec, you could use a ball hex on the end of your torque screwdriver/wrench, just keep in mind those will strip out before a regular hex would so be careful.

[@actslore]

Interesting to see your methods of putting this rail on

[@watchin-stoof988]

What height dot needed to get that front iron at lower 3rd? Looks tall

[@tarheelrealist8935]

Brownell's has DD M4A1 SOCOM profile uppers...sans F/H, BCG and charging handle.

[@carlkleynhans3864]

S&W M&P15 16 inch 🤔 will it fit..

[@12345678971926]

What kind of adjustable wrenches are you using? I like them.

[@jojomasterson4852]

It's a Knipex Pliers Wrench, IIRC the one I use in this video is the 10" version.

[@masterxiong7368]

Looks freaking sweet bro!

[@epikboi9508]

Will a emg daniel defence licensed 9'5 m4a1 handguard fit a LM4D

[@christurner8255]

Bro help will this rail fit the Cilt OEM 2 or is the gas block too big

[@jojomasterson4852]

If you use the non FSP rail, you may need to file the gas block around the pin area since the FSP rail has a cutout for the pins on the bottom section. It may work without fitting since seems like there is enough clearance there even without the cutout but it may be pretty close.

[@christurner8255]

​@jojomasterson4852 thanks for the reply. My bad though, I meant OEM 1. I got the Colt OEM 1 and the rail back in September but still haven't installed it yet. I'm working up to it.

[@SOFLOFirearms]

Just got mine today can’t wait to throw it on

[@Dan-di9jd]

Don’t do it!!!!

[@martinflores9382]

Do you use a carbine length gas tube and barrel ?

[@jojomasterson4852]

Yes the barrel and gas system are both carbine length。

[@hartrash]

Did that rail come with the hardware to mount the m203?

[@Vane_M4A1]

The M203 mounts to the barrel, the SOCOM profile here, yes does have the cuts that the 203 clamps on to. As to answer the rail part of the question most AR handgaurds/rails have a top and bottom section, with the bottom section not needing to be fitted to install the rail, allowing access to the bottom of the barrel to mount the 203.

[@ryanchoat7248]

You just use a standard barrel nut?

[@jojomasterson4852]

If you have a DD RIS II it should come with its own proprietary barrel nut and wrench.

[@kripkilla88]

MEILING MENTIONED OORAH

[@SushiNinja09]

What pliers are you using? Also what rail length did you use?

[@jojomasterson4852]

In this video I'm using a "Knipex Pliers Wrench" I think its the 250mm version. The rail was a DD RIS II FSP which is a 12.25" rail iirc.

[@maxwellmortimermontoure7274]

I am a sucker for quads and fixed front sights

[@trevorhonicutt8659]

Will a 16 inch Fn barrel work

[@jojomasterson4852]

It should work if you use a barrel with a carbine length gas system, if you use a different length gas system you might run into issues with there not being enough clearance for the gas block.

[@trevorhonicutt8659]

Thanks 👍🏻

[@pliskenx51mm83]

That was a good video!

[@vietnamtactical]

Idk ive always thought those rails were cool when i first got into guns and now i remind myself how fundamentally goofy they are, but i dont doubt it works for you good video

[@ppi_god_619]

I picked up a Socom profile from Faxon

[@sranney1]

Thx good vid

[@a-n-d-r-e-w-k]

Guns and anime. Home.

[@bennyknot]

You should not ever use loctite when threading steel screws into aluminum.

[@gphone2733]

got that thumbnail game down

[@TheLouHam]

That is not a SOCOM barrel, that’s a government profile barrel. You can tell by how skinny it is behind the FSP.

[@BigDaddy-jo8ig]

Heavy boom boom 😢

[@ryank0351]

Too much work,I'm just gonna buy one from broenells😊

[@bigfootdrums]

"Hao To Install" haha

[@kensmith8832]

Hao is Mandarin for Good. Not sure if he knows that.

[@michaelmarkle5133]

500 for a rail. Id rather buy ammo