Can i just lubricate the channel faders without disassembling?? I don’t really see where it would be an issue.
@djab2038 ай бұрын
If the faders are bad, they will require replacement, but if they are just getting stuck then you can use DeoxIT Fader Spray a.co/d/cuGgVzK
@DjMulen Жыл бұрын
Thanks for sharing this procedure, it's very helpful. Cheers!
@djab203 Жыл бұрын
You're welcome!
@MorbeatoАй бұрын
Im currently in the middle of this job and Im stuck on getting the fader off of the board. The metal that you bend down to hold the fader in place will not come up. I've gotten as much solder off as i can and it still wont come up. Im afraid to scratch the board by using anything except plastic to pry it up. Do you have any reccomendations?
@djab203Ай бұрын
So be very careful with it and make sure to use a lot of flux and wick to clean it well, then after using a sharp Craft Knife bend it while holding the iron against it. use this - a.co/d/53haX31
@Publicidadessmiley13 күн бұрын
How much you charge to fix channel 2 fader and left scratch ?
@djab20313 күн бұрын
Price is estimated between 120-150 depending
@Publicidadessmiley8 күн бұрын
@@djab203 where are you located at ?
@djab2037 күн бұрын
@@Publicidadessmiley Seymour CT
@djilyaz10 ай бұрын
Looks like a drink may have been spilled into my SRT 1000, the shift button and a few buttons on the right side are stuck, there's no close pioneer repair place, do you think I could fix it myself I just wanted to clean it out with some deoxit,
@djilyaz10 ай бұрын
I guess the real question is are the buttons hard to get to
@djab20310 ай бұрын
@djilyaz If the liquid spill was recent you may be lucky and not have any corrosion so I suggest you clean it ASAP using alcohol. The right side can be a pain to get to but you can watch a few KZbin videos on how to do that. I do side repairs but I'm located in CT.
@leonelchavelas216 Жыл бұрын
I have a problem where the volume faders is causing my EQ’s to cut any tips
@djab203 Жыл бұрын
Sorry just saw this message ... Is this happening with all channels?
@jesuscarmona42852 жыл бұрын
My 1000 srt doesn’t want to turn on anymore, any tips? 🙏🏻
@djab2032 жыл бұрын
Start with inspecting the power adapter then proceed with check the power board module.
@gfabian8509 Жыл бұрын
@@djab203 I have the same issue. changed the power adapter once started working fine and then it happen again it doesn't want to turn on again. last time I tried to turn it on the quantize was flashing red then it didn't turn on any more please help.
@djab203 Жыл бұрын
@gfabian8509 that's an indication of a bad power adapter. Get another from Amazon since they go bad allot. If you plug them into regular outlets without a surge protector they go bad. If the adapter is not your issue you need to open the controller and check for liquid damage.
@jesuscarmona4285 Жыл бұрын
@@djab203 will buy one and get back to you, thank you!
@argelysjiminian8161 Жыл бұрын
@@gfabian8509what did you end up doing? I got the same problem and after speaking to a repair person on the phone they mentioned that it was probably the controller. I bought an adapter with identical specs to the original power cord and the controller still flashed.
@starlite3597 Жыл бұрын
using wd40 on that madness lol
@djab203 Жыл бұрын
I think I over did it :)
@starlite3597 Жыл бұрын
it's grease you want not wd40 lol
@djab203 Жыл бұрын
@@starlite3597 Agreed 100% :) For some reason wd-40 is always around. Next maintenance I will use grease.