DeLonghi ECAM How to replace brew group regulator

[@johnteslade]

Brilliant guide, thanks. I've just replaced the brew regulator on my ECAM220 (Magnifica Start) using this video. The way to remove the front panels are slightly different on this machine, but the rest was exactly the same. Getting nice coffee again.

[@pflpfl9339]

Your explanations and warnings are so helpful ! it's obvious u really want to share your experience ; for that a big thank you

[@DamianSwarlik]

thanks that movie i saved around 150 euro for professional service, many thank you for this tutorial 😎

[@heirheinrichvonscrofula9151]

Thank you sir. A great guide on how to replace this difficult to get-at part.

[@imperial1a]

Благодаря ти Милене,жив и здрав!

[@toobemaster]

Awesome instructions. Thank you. I followed exactly and my machine is now working correctly.

[@adamwojcik356]

Hi mate, thanks for your video, it was big help to understand how it works. Btw I was able to replace broken part without splitting machine on half. It's possible to get only this broken piece of plastic, not whole part. All what I needed was dentist's mirror, pliers and some simple hooked "pushers" to take off and put back locking washer. Regards

[@pontuspaulsson3435]

Exactly what I did

[@eubikedude]

@@pontuspaulsson3435 Me too. :)

[@eubikedude]

Where can you get just the pusher part?

[@bubbleboymusic]

You are a genius man and so handy!

[@ginana8288]

Thank you very much! Though my machine is ETAM29.660, I can modify your work. Your video was the only English explanation that I found all day long today :)

[@edswasey2764]

Great instructions, mine is a newer model but still same body. Thank you for this well-done video

[@michal_wojcik_official]

Many thanks for detailed video

[@jorgencolsoul1544]

Perfect instruction video ! Thanks man !

[@alexalixandrica]

Perfect! I was looking for a tutorial like this!

[@lukaszdobosz5064]

Thanks for help part replaced and i found it pretty simple especially when you make photos

[@bormotuxa2463]

Thank you very much for this video. It was a big help for me.

[@techheck3358]

Thank you for this 😊very helpful. Dumb design to place on the inside!

[@henriquesoares8571]

Great video man, thanks!

[@andrea99boban]

Thank you so much! Saved the day. Cheers!

[@TheShonepa]

Thanx men, perfect video!

[@soundwaynes3885]

Thank you my friend i have the same problem with my magnifica evo and now i have an idea... by the way whats the name of the parts and how to order a new one? Thanks

[@gorangotbo]

Thanks, perfect video! Works fine when replaced, But when I put the machine back together the brew group regulator would not spring back. Any idea what is wrong?

[@pjmesquitar]

Good vídeo. A have one like that machine. But subtly dont switch on. Any lights can see in front. Any cause in the main board ?

[@TheCasius01]

Thank you so much for the video it is really helpful. But i have 2 questions: - what kind of spring is it, as this piece drop. -Is it the same thing for the magnifica evo?

[@lukebransby600]

Do you have a video on the temperature switches. My machine say” HEATING UP PLEAEE WAIT” and stays on this till I give up and switch it off. Some times I’m lucky and it works or it goes to GENERAL ALARM. I have cleaned the entire machine

[@raflucique]

Top man! Thanks for this video! Mine brew group was stuck so I couldn't get it out. I found out solution because of these video. Lots of coffee bits was stuck in brew piston. I noticed also that the arm of the brew group is chiped off. Hopefully the arm is possible to buy itself. Do you think it's possible that my Delonghi is not runing rinsing cycle because of it or it's some other issue as well? Water is going through the steamer as normal. Thanks 🙌

[@inteh9839]

Hello. For Philips ep2220 40 coffee machine. Could you find a video of how this coffee machine is separated and cleaned inside?

[@mstockma]

Very helpful video! I have a similar problem but the regulator is fine. There is another piece towards the front of the machine, with a spring, that looks like the regulator but is not. It broke on me. Any idea what it is? I cannot find the replacement part! I think it will require the same halfshell effort to replace a tiny piece.

[@klavs8788]

Have you find a solution how to change that?

[@GaryMelechinsky]

In this video he says it can be replaced without tearing the machine in half. You would probably need a dentist mirror to see the screw and a short screwdriver to fit in there.

[@watan1231]

God bless you

[@eubikedude]

I repaired my one without pulling the machine apart. I removed the circlip from the part in the machine and removed the "pusher" and did the same on the new part and swapped them over. I didn't get the circlip back on yet but a) there seems to be enough pressure to keep the pin in place and b) a piece of e.g. mylar tape over the pin end (outside) should work too. Why they didn''t put the pin in the other way around so you can get at the circlip from the outside is mind-boggling. Built in service needed/obsolescence? :( Also, I don't think the pusher was installed correctly on my machine from the factory, the hole in the pusher was still intact, so impossible for it to have come away from the pin ... I think it was just pressed in on the spring - possible sticking out a bit too much and that's what cause it to break (snapped off at the plastic pin that the pusher spiring sits on to). So I'm hoping it lasts much longer now.

[@DrMary32]

Hi! I have same machine but the issue might be different, it doesn’t respond to commands, if is plugged in, is playing alone: switching on and off, water comes out and in the end I cannot make any coffee as buttons are not responding to orders. What that might be? Thank you!

[@GGodis]

Good video. I have the same coffee machine, and this "regulator" part is periodically keeps breaking for me.

[@RobbCarel]

You have to make sure that coffee maker has enough coffee inside. When it is empty it breaks like this

[@yordantomov4184]

Zdravei kak moga da se svurja s teb

[@kirstendewaelheyns1602]

Could you tell me where to buy the part ? Thanks for the super tutorial!

[@milenstoitsev6676]

eBay

[@milenstoitsev6676]

DeLonghi Parts - Brew Group Valve Guide for ECAM Models - 7313214521

[@user-xj7ti8jv4d]

Very good video thanks 1- If the machine goes to safe mode, how to return it back to its normal mode ? 2--I have some machines which grind very small amount of coffee how can I Increase the grind amount? Thanks

[@robertdaradics9998]

Hi. same problem here :( . Did You find any solution ? Thank's.

[@SaitamaZ]

How can i remove heater to test sensor ?

[@markrebers8147]

Dear Milen (and others), I learnt a LOT of your Delonghi videos, this part was broken with me and i replaced it, now my grinder is only 3 seconds and then stops. What could be reason? Thanks anyone who can help me!

[@stefanbicboziji]

As he said, machine got stuck in safe mod. I think that you need a new pcb (i hope i'm wrong)

[@Denisjjj]

In my machine the piston of the infuser doesn't reach the upper position but stop at 3-4 millimiters from the top: the result is that a part of the coffee ground remain on the filter. Who know which is the problem?

[@ttttonyyyy]

It is this part in the video, the regulator, with it broken it doesn't move the arms on the brew group enough to push the piston all the way to the top.

[@pontuspaulsson3435]

Hi , there is a better way. Just replace the broken plastic part by removing the locking shim and pin. Easy done. The tricky part is to assemble again. But is possible, took me total of 20 min first time.

[@ivankakostadinova2400]

Здравейте имам нужда от ваш съвет ако може🙂 Имам кафе машина Delonghi Autentica но нещо не пуска вода и следователно няма кафе☹ а другата страна има вода смисъл прави пара и пуска гореща вода моля за помощ ....