Wenn ich sowas sehe, könnt ich kotzen!!! LEUTE !! Wenn man den ganzen Sch.... schon zerlegt, dann hat das gefälligst gereinigt zu werden!! DAS IST PFUSCH !!!

Bei meiner Maschiene blinkt immer das rote lämpchen 6:59 7:00 Was ist das !

Milen, Thank you very much. You are a life saver. Where do you get parts for Saeco Italia?

Awesome thanks

hi Milen, thank you for the movie....after service like that, do i have do some position calibration? My infuser sometimes stop to low, and from that reason i am not able to remove the tray with coffee grounds. I did factory reset by holding 3 buttons and plugged in the cable to the socket, but it didn't help.

Hey, wonder if anyone can help me. A part of my original brew unit for my Saeco Magic de luxe coffee machine broke off, so I ordered a new one with a new spring and ball valve thing. Before everything worked ok, but now when I try to make a coffee it doesn't come through. I've observed the process with the door open and see that from somewhere near the top of the brew unit the coffee spurts out, with it all ending up in the brew unit and the bit where the old grains go. When I remove the ball from the brew unit, the coffee comes through fine but obviously really weak and not nice tasting. Could anyone advise me what exactly the problem could be here? I've cleaned the brewunit and regreased everything, ive ran the decalcifying cycle with the phillips descaling solution thing, ive tried the old ball and spring. This has all been over a long time period though (since September non-functional). Gratefuly for any help - its so heavy i dont really want to have to take it to a repair shop - ive no car! I've taken a video so can provide if would be helpful. thanks.

How can i remove heater to test sensor ?

Subtitling?

You saved us so much money thank you!

Thank's ! Good video

Hi, Milen, where can I get parts to refurbish my Royal Cappucino coffee grinder. Thank you!

Hi, can you tell me where to get the parts you are replacing on this video, I need to repair my grinder. thank you.

Vorrei fosse in italiano

Thank you very much. I solve problem with my old but very good Vienna coffe maker. Repair for few dollars. Thak you for advice.

Thank you very much. Your tuto help me a lot...

Hello, if the thermo fuse is tripped will the machine power on? Sacco odes giro plus thanks

Great tutorial! Thanks.

Very grateful for your video Milan, my 12 year old Magnifica had never been serviced and luckily for me had only just started playing up, thankfully your video is precise and your information was very simple to follow, I changed the o'rings and lubricated everything as per your instructions, I now have a perfectly working Magnifica.... Thank you x

Will try this tomorrow! Thank you for the very detailed explanation!

Does the third o-ring need lubrication? In the video just two ring were lubricated.

Great instructions, mine is a newer model but still same body. Thank you for this well-done video

Thanks, brilliant video, lots of useful information repaired my machine for free thank again

Hi Milen, my Sacco Poemia coffee machine suddenly stopped bruing coffee .When i turn the switch to coffee mode hot water comes through the milk frother.Please your help will be highly appreciated,thanks in advance.

Where did you buy the parts? I want to order them all 🙂

Thank you for this we just fixed our leak following your great clear video

Can you please help i have saeco lirika. The problem is on lcd red servis error 5. When i turn it on it shows one from and an arrow circle on lcd. Starts brewing unit turns and getting ready. Than it turns back. Than the machine pumps the water under it. There is no Blockage.

Your videos have been very helpful! I have fixed several units with your help. I am having a new problem and I wonder if you might have an idea what is wrong. My ESAM 3300 flashes green lights when I start it up for about 5-10 minutes and then the trouble warning light comes on and it won't go into ready mode. I have check the temperature of the generator and it is very hot, but the unit doesn't seem to "know" that.

Hello, my DeLonghi Magnifica S ground the coffee too short. About 3 seconds, which is why the coffee is very weak. Do you think the Hall sensor will be the problem? Would you suggest checking something else first? Thanks

Ok! Köszönöm! Kár hogy sötét a videó!

Hi Milen, Another Great video I just wondering if you could help me with my Starbucks Sirena it leaks from the group head (lower boiler Assemble) even without the portafilter attached. It just seems to keep leaking and dripping from the middle of the grouphead where the brass holding screw sits. I have change the spring and mushroom seal in the group head area. Any suggestions will greatly be appreciated. Thank-you in advance Bill

WOW! Super useful video! I have an old ENA 3 that we got as a gift that had stopped working for the past month. Managed to get the front off. Filled the sink with brown goop. I don't know how we managed to get a decent coffee out of the thing with all that stuff clogging the insides! Thanks a bunch!

Hello!!! How do you set the right position to 0 when you turn on the device so that it is well synchronized when it starts?

Good! video, thank you very much, really well explained, I will be able to clean mine and change the parts if necessary.

Where did you buy the LCD ?

Dziękuję

Hello Milen! Thank you very much for your help 👍

❤❤❤

Do you have the part number or name of the original and for the better springs? How to search for the parts? Can it cause a shortcut if this leaks the water? Ours break the phi-relay.

Thank you so much, you made my day 😍😍

Hi! First thank you for your video! Can you help with a issue i have on my philips series 2200 please? The machine is making coffee ok, but not frothing the milk like usual, it just bubbling in the milk but slower than usual. Do you think it can be the pump or something else? I took the pump apart but all orings look ok, also the little ball.

So very informative, thank you Sir! You are awesome!

I have one of these machines and I am getting the Ventilate error. I have taken out the pump and its clear and it spins freely. Any idea what might be causing the error

Thanks, very helpful. I've just cleaned mine.

Error 21 what’s that pls?

Bro i got problem with Latte go 5400. I push it on and it starts immediate preheating, it stops around 50% and displays error 15 - heating problem. The heater in the boiler works fine, so as the NTC thermistor and both security thermostats. I realised there is no water going to the boiler thru the Ulca vibrating pump so it starts preheating without any water and later it cut off one of the sec. Thermostats because the heater is heating the case and not water. But i checked and completely repassed the Ulca valve and it works fine if I put it directly to 230V. So.. I though there could be problem with the AC switching thyristor that is switching the pump. Or the machine things that the boiler system is full of water so on the startup it starts immediate preheating but.. The capacitivw water level sensor, if it fails, would it even register the water tank in the input? Because its registering the insterted tank dude im fcn tired of this crap.. I need to solve it somehow

Thanks for sharing this knowledge

Great series of videos. Do you have an email address. Garry

I just want to say thank you for this video, I followed your steps and it solved my water leakage problem by cleaning the chamber attached to the boiler - saved me from buying a new machine!

Perhaps this will also help to prevent leakage kzbin.info/www/bejne/hXu6mKiJnN6ZasU

Thanxs Bro