DeLonghi ULKA Water Pump - Repair | DeLonghi ECAM Magnifica S

In this video you can see how the ULKA water pump of a DeLonghi coffee machine can be repaired easily, quickly and inexpensively.
M Y P A Y P A L T I P - B O X
_____________________________
www.paypal.me/...
Affiliate links:
Bezahlter Link:
U S E D P A R T S
_________________
Dichtung+Kugel: amzn.to/3c98AWz
ULKA Pumpe: amzn.to/2WzgAdg
Silikonfett: amzn.to/2L1EFnE
#Ulka #WaterPump #Repair

[@austinado16]

Excellent video! Thank you for making it. I just purchased an espresso machine that had been in storage for years. The pump would not prime. I used a plastic syringe full of water, to force water through those check valves, by removing the filter from the water supply hose, and putting the syringe onto the hose. (I got the plastic syringe from a local drug store by asking them if they had syringes for giving pets medicine. This kind of syringe has no needle.) After the pump was force primed, it worked, but the flow was very low. I removed the pump, and took it apart as you show here. I found that small 9mm x 5mm x 2mm o-ring was hard as a rock. I replaced it with one from the plumbing department in the local hardware store, and now the pump delivers a lot of water! Saved myself $45.

[@davidbouman]

I took my pump apart and of course didn't know how to fit it back together. Thanks to this video I'm having a coffee now. Thank you!

[@stambetors]

I fixed the problem with my machine thanks to this clip. Thanks!

[@dx5537]

Démontage détaillé et précis. Vidéo de qualité. Super ! Merci.

[@bangdangough7948]

Thank you very much! I fixed with the help of your video our Delonghi Magnifica S. The little O ring was the problem.

[@_nerko]

Thank you so much bro... Some heroes don't wear capes

[@jaycee30865]

They wear black gloves though.

[@СергейХалява-в7р]

ⁿ

[@Lordosvk]

Mate you are hero of the internet !

[@easterneuropearchives7177]

Brilliant thank you. No coffee, no workee. But now workee again

[@robertjaszewski3568]

Dziex Bruder! Miło patrzeć na Twoje poczynania. Picie takiego espresso to sama przyjemność

[@abdelkadersoultana4532]

Merci pour ta vidéo explicative, j'avais démonte... Mais mal placé le petit joint torique qui c'est déchiqueté ...lol ;-) Cool tu m'a sauvé une Délonghi !!

[@maestro2279]

Ogromne dzięki za pomoc, dzięki Tobie mamy na święta kawę z ekspresu!!! :) Daję like i suba :)

[@gravestonemyth]

Thank you. This was helpful in repairing my Gaggia Berra.

[@Danrchy]

Great video! I will follow this when i take apart my Magnifica S. My machine just stops at the pump sekvence when starting up and eventually the warning triangle shines, not blinking. The pumping never starts but i can smell its heating up. So ill try change the pump before i discard the whole machine

[@yt.myworks]

Try to descale the machine before buying a new water pump. Sometimes the water pipes are clogged and even a new water pump does not help. Most of the time, the pipe that runs from the heater to the brewing group calcifies.

[@ogundemirhan7612]

Teşekkürler çok faydalı bir vidyo çekmişsin Türkiye'den selamlar 🙏

[@yt.myworks]

Thank you, best regards!

[@gordonondis4840]

Hi, thanks for this video! Our Prima Donna was giving us this message. I replaced the o-rings in the water pump, it now makes coffee, although the pressure still seems lower than when it was working 100%. Also, the machine takes a very long time to switch between functions, i.e., from steam to hot water to coffee. I replaced the flow meter, that didn't fix it. I notice some air in the water line, how do I fix that?

[@Ramzi_Az9]

Thank you so much for this awesome content, really helpful, worked 100%, god bless you 🙏🙏

[@KeesRecourt]

Great video, I am performing your steps. Question: do you use a specific glue to connect the blue item again (5.30 min)? What is it, a fuse or capacitor?

[@yt.myworks]

The blue part is a fuse in case the water pump overheats. I use hot glue gun to fix it. But the water pump can also be taken apart without removing it.

[@KeesRecourt]

@@yt.myworks Thank you! I succeeded in replacing the small o-ring and ball by using the Amazon kit. Most difficult part for me was reconnecting the tubing at 6.07 min. Initially, I did not push it far enough into the holder, so the connector did not fit properly. Further, there was a lot of noise during the first run, probably because the pump/tubings/noise reducer had to refill with water again. But until now, after five cups of coffee, all seems to work properly again. Will test for at least a week before being satisfied ;)

[@thomaskamm1019]

Thanks for the video. My pump is making a loud vibrating noise - I believe it is coming from inside the pump itself. Anything I can try?

[@thomaskamm1019]

Also - do you know the difference between the white pumps vs red pumps?

[@yt.myworks]

Hi, the pump makes a loud noise when it has run dry and is not getting any water. White and red water pump have different parameters.

[@HowAdd]

@@yt.myworks hi, so if the pump making loud noise and I am sure that even after replacing O-ring in it doesnt pump water because i tried everything. Its necesary to replace whole pump? Thank you for your help.

[@HowAdd]

@@yt.myworks so, i just found out that pump is fine. So my problem is more further inside the machine. How can i unclogged rest of the machine if i am not able to pump water for descaling?

[@yt.myworks]

@HowAdd Keep trying to press the rins button with the descaler in the water. Leave the machine on for two to three hours. If that doesn't help, turn off the machine and leave the descaler on for the night. If that doesn't help, you'll need to disassemble the coffee maker.

[@hass1947]

Professional and very helpful video (as usual!). Thank you!

[@SylvainDaclin]

C'est validé également, très bon tuto 👏

[@galaxycleaningegypt]

الله ينور .. طبيب جراح

[@huzcer]

Hello, I'm getting drops like this for the coffee making and also when the cleaning water procedure happens on machine start up. I replaced the small o-ring but it's still happening. do I need to get a new pump or could it be something else?

[@huzcer]

?

[@yt.myworks]

It could be that the heater is calcified. Check the water line coming from the heater to see if it is clogged. Then try to descale the machine properly.

[@huzcer]

@@yt.myworks appreciate the response. the steam wand works fine by the way - would that still work if heater calcified?

[@yt.myworks]

@@huzcer I think it's possible. The steamer has its own water pipe. But it's just my guess.

[@huzcer]

@@yt.myworks thank you again. I had been regularly descaling with lactic acid but maybe it was not strong enough. I ran 50g of citric acid through it a couple of times and now water is more freely coming through the coffee outlet again.

[@ChubChik.]

Спасибо за познавательное видео 👍🤝👋лайк и подписка 🔔

[@Ramzi_Az9]

Thank you for the video, very intuitive! But I have a question please, I have changed the pump to new one but the same problem remained? Any solutions?

[@yt.myworks]

Which problem do you have?

[@Ramzi_Az9]

My mistake, so even the pump was changed correctly but I had some small stones stuck there in the pipes, I had to buy a special product and it worked fine. Thank you for your help

[@BiltongBoy]

Very handy tips. I like your videos. If tiu can help fix my problem i would gladly send you a tip. The pressure of the steam coming out the wand is 50%. I’ve replaced the water pump with another but still the same problem. A problem I have now after replacing the pump is red triangle. There is no residual coffee ground and machine is clean. Thanks. Hope to hear from you soon

[@yt.myworks]

Hello, first try to descale the machine properly. The Teflon hoses may be clogged. If it doesn't help, please contact me again.

[@mahatma_manett]

Dichtung und Kugel getauscht. Das war’s schon. Vielen Dank 🙏

[@ignisGladius]

Must you fill the inside the pump with water when reinstalling? It's just making loud noises and not releasing water after installation.

[@yt.myworks]

You can fill the pump with water, but it is not necessary, after a few seconds the pump will suck in the water.

[@ignisGladius]

@@yt.myworks It did. I was worried the aggressive mechanical movement would damage a component inside the pump, since air creates less resistance. But as you said, after 20-30 seconds, it started releasing water.

[@paulkrupa]

@@ignisGladius this is a positive displacement pump and can prime itself. If it does not the tiny ball may have been left out. This ball is part of the valving. A damaged o ring or damaged ball can also prevent the pump from pumping at the full rate. The vibration pump installation can affect its output profile. The output can be controlled with pulses of electricity and a pressure regulating circuit on the output. A buffer tank can be used to smooth out the output pulsations. I think this a very good device for this application. It does not have a heavy duty cycle and output is limited. It can reach high pressures adequate for its application. The on-off control characteristic combined with a return spring makes for a simple reciprocating pump with out a rototing motor. This setup lends itself to easy control for output versus controlling a rotary pump output. The latter would require a motor speed controller which is more complex when regulating output. I found an interesting video comparing shots pulled from each of the motors and it reported significantly better product with the rotary motor. I don't know whether that is Lucky or whether that is irrefutable. Depending on the pumping pressure regulation arrangement, one should be able to produce very consistent output from either device. Given the reliability and low cost of the vibration pump I think that would be the choice for most devices in lower price range.

[@lifeisfuneh]

Hi there! Do you ever see problems with flow back valve in the front nipple of the pump? Seen them stuck before. Did you find source where to buy the mushroom rubber part? Thanks!

[@hass1947]

Hi! Have you some experience on Nespresso Aeroccino 4?

[@JonathanGoggans]

Hi myworks, quick question. Should any grease be used on the gaskets in the pump? Looks like I will need to replace the o ring and ball on mine and I want to be sure I put it back together right.

[@yt.myworks]

I don't grease the "O rings" in the pump. I wish you much success with the replacement!

[@madeinbalkan.2610]

No grease. But don't forget to put rubber gloves on...

[@herminemohr9513]

@@madeinbalkan.2610 ö

[@hehen9628]

Bei mir war es der flowmeter / Wasserdurchflussmesser auf der Seite Richtung Pumpe wars verstopft. Habe es mit ner Nadel wieder freigemacht. Das Loch ist so klein, vielleicht 1.5x so groß wie ne Stecknadel.

[@HarrieDumenil-w5s]

Hi, I've just replaced the pump with a new one and still have the same issue. When it turns on and rinses and turns off and rinses the water flow isn't flowing, it's dripping out very slowly and it makes a lot of noise before it starts flowing. Any ideas what this could be?

[@yt.myworks]

Hi, while making a cup of coffee, is the water pump running normally? It could be that there's a leak, causing the pump to be noisy when it sucks in air.

[@theorychile]

can i find that white ball in aliexpress??

[@yt.myworks]

I think so.

[@elenamertens7434]

Ich hab meine auch auseinander gemacht um Dichtung umzutauschen und beim Röhrchen wo Feder und Kugel reinkommt auf der andere Seite ist ein Gitter ich hab das Gitter rausgeschraubt drin ist eine Feder in zweigeteilt, jetzt eine Frage ist das Absicht oder defekt?

[@yt.myworks]

Hallo, die kleine Feder auf der die Kugel sitzt sollte in einem Stück sein. LG

[@elenamertens7434]

@@yt.myworks Danke für die Antwort. Ja , eine Teil der Feder ist auf einem Stock andere war auch drin! Wo kann man sowas kaufen? Ich brauche auch diese Plastik Kugel, die auf die andere Seite, auf die Feder kommt!

[@yt.myworks]

Hallo, die Dichtung mit Kugel habe ich unter dem Video verlinkt. Eine neue Feder gibt es leider nicht zu kaufen. Da sollte exakt die gleiche eingebaut werden sonst arbeitet die Pumpe womöglich nicht richtig. In dem Fall würde ich eine neue Wasserpumpe kaufen. Bei eBay sind sie am günstigsten. Achte auf die Bezeichnung, dieser muss übereinstimmen. LG

[@elenamertens7434]

@@yt.myworks Danke für die Antwort.

[@TommyNL85]

Witch screw driver do you use to open de machine?

[@yt.myworks]

@Tom I use these tools: Akku-Schraubendreher ASD (3,6 V) amzn.to/36CtoVU Torx 20 mit Bohrung: amzn.to/3xN6PcS

[@TommyNL85]

Thank you so much for your message. Thanks to your video, I made my coffee machine again! There was something wrong with the pump but he's thanking again!!

[@c.patricksadowski9959]

Where do you get the “O” rings? What size?

[@yt.myworks]

I buy most of the new components on ebay or amazon, as well as the "O" rings. You can see the size on minute 3.10 in the video. Also I would recommend you, to change the little ball in the pump.

[@c.patricksadowski9959]

Thanks. I was able to find some orings and balls on EBay. Hope they will work. Do you know where I can get the plastic part that goes through the pump for the Francis Francis X7.1? Thanks

[@yt.myworks]

@@c.patricksadowski9959 ​ Unfortunately I don't know where you can get the plasic part because I didn't disassemble the portafilter yet.

[@untitledduck9675]

@@yt.myworks where can i get you big o ring that seals the plastic

[@yt.myworks]

@@untitledduck9675 You have to survey the O ring and search for it on ebay or amazon.

[@NicolaDiNisio]

Very good job, but set the machine for a much shorter expresso ;)

[@randallrosa7313]

Hello! I have an issue with my Magnifica XS that my first pull of espresso is about 1/2 the volume as the ones that follow. Ive replaced the water pump, regulator and flow pump, still have the problem. Any suggestions on what to look at next? thanks!

[@yt.myworks]

You have to pay attention to the degree of grinding, it must not be set too fine. Also check the brew group for blockages, then you can try to descale the coffee spout by repeatedly pressing the flush button.

[@boefje1976]

Thank you so much!very clear,helpfull,this helps a lot and saving al lot of money!My little spring is broken.Hopefully i can find one that fits!

[@kjeldschouten-lebbing6260]

Be careful with replacement springs, you actually need a spring that is designed for this device, not a random spring that happens to fit. The strength of the spring is the thing that pushes the water and what the electromotor (coil) works against. Using the wrong spring will damage things.

[@medhijobard3838]

Hello… when I try to make a coffee, it doesn’t flow and it makes an small electric « bzzzzz » noise. Is the pump for sure ?

[@yt.myworks]

Hi, it could be that the pipes are clogged or calcified, which means that the water pump cannot push water through. Did you descale the machine regularly after request?

[@medhijobard3838]

⁠@@yt.myworkshello ! Thanks for the answer, just changed the pump. 30€ and everything is all right

[@Chappomusic]

I have a 2 small jura ena and it works perfect only the pump from one makes more sound then the other . Like it’s doesn’t have water . But he gives enough . Can it be a pump worn out ? It’s a bit like the sound or this machine but harder , sharper . The other ena is quieter but gives slower water - so don’t know what’s the trick :)

[@yt.myworks]

I can't say for sure, but I recommend descaling the machine that runs quietly with a special descaling agent. For the other water pump, I recommend checking if the same amount of water is coming out to rule out a defect.

[@Chappomusic]

@@yt.myworks Well you were right : even I thought the machine was descaled enough - two extra cycles helped a lot . Hence one is louder then the other , but it is not that loud anymore .

[@gaganh1]

Hello. I have a problem with my machine Delonghi Etam SB 660 where only steam comes out instead of foamed milk. It works once in a while randomly though. I already tried to change the milk coupling but that didn't help. Do you think replacing the 2 way solenoid valve will help? Or could it be something else?

[@yt.myworks]

Hi, in most cases it is due to the solenoid valves. But also check whether there is perhaps a calcification.

[@gaganh1]

@@yt.myworks Thanks. After decalcification, i replaced the Solenoid valve and the milk dispenser coupling including the pipe. It works now for 1-2 coffees after starting the machine. But not always. Also when selecting only the milk option gives only steam! No idea what i could do more.

[@georgekossieris6734]

Hello, I hope you are doing well. I have the same model, and about a week ago the machine would not make any coffee. Now , when the machine starts for the first time, the pump starts to work (for the first rinsing) but then the sound of the pump goes down until nothing is heard anymore after 2-3 seconds. Then I am getting the error "coffee is too fine",it stops and then some water leaks in the coffee tray. I have checked all the pipes, there is no scale in any of them, and I am descaling regularly. I have replaced the diffuser with a new one, still nothing. I have also replaced all the orings. I don't know what else to check. The hot water however still works. Any suggestions please?

[@yt.myworks]

Hello, you can also check the water pump but I think one of the water pipes is clogged. Most of the time it is the teflon pipe that goes directly from the heater to the brew piston.

[@georgekossieris6734]

@@yt.myworks thanks for the quick reply. I am not sure what was wrong, but I was also thinking about the water pump. So I just disassembled the pump and then put it back together, without changing / replacing anything. And it worked fine after that. Really strange. But thanks again, your channel is super helpful!

[@imrekoreny9355]

I had the same problem. I have checked all the pipes, the pump, every part of the machine. The problem was a congestion in the infuser. You should remove the stainless steel cap of the infuser and clean the surgace correctly. There you can find a ball “valve”, it can stuck by the coffee oil and grease. Just push it and try to clean it. At first I have disassembly the infuser, not a big thing and in this way you can see the other hole of the duct between the rubber o rings.

[@huyenanhnguyen6143]

Very useful. Thanks alot

[@izzzzzz6]

Is it obvious if the o ring is worn?

[@yt.myworks]

The O-ring 5/2 mm should be replaced.

[@izzzzzz6]

@@yt.myworks I'll try it. I might have one downstairs in my AC o rink kit, (the green ones). If i get time i can swap out the parts with my working pump to double check if that's it. It's definatly expanded but the seal feels ok but it might be slowing the oscilations from being a bit squished in there. Funny how the pump only works one way round even though the power is AC.

[@TIRestoration]

Thank you, was helpful

[@peterpan8355]

Moinsen, ich habe folgendes Problem: Ich schalte das Gerät ein, dann startet sich der vorgeschaltete Wasser-Reinigungsprozess. Beim Wasserziehen zischt es leicht aus der Düse; bei der eigentlichen Brühausgabe zischt es auch kurz vor Ausgabe leicht aus der Düse, womit kann das zusammen hängen? Danke im Voraus für einen Vorschlag ♥

[@yt.myworks]

Hallo, welches Modell ist das? Meinst du Düse für den Wasserbezug? Es könnte sein, dass das Magnetventil vekalkt oder undicht ist und nicht mehr richtig schließt. Am besten du lädst ein kurzes Video hoch, vielleicht fällt mir dann etwas auf. LG

[@peterpan8355]

@@yt.myworks Hallo, das habe ich soeben gemacht:) kzbin.info/www/bejne/pGTVlHSArt2tatU

[@yt.myworks]

@@peterpan8355 Hallo, das hört sich an als ob eine der Dichtungen am Brühkolben oder Brühgruppe nicht halten würde. Beim komprimieren von Kaffee-Puck entweicht die Luft irgendwo. Wie viele Kaffeebezüge hat der Automat bereits? Sieht ziemlich neu aus.

[@peterpan8355]

@@yt.myworks Okay, dann werde ich mir das mal genauer ansehen, danke für den Tipp! Das Gerät ist 2,5 Jahre alt, durchschnittlich 2-3 Kaffees. Lass dir ein Abo da :)

[@mihaiosanu6481]

Gracias problema resuelta

[@checkwhatsleft4565]

What kind of materials this 4mm plastic ball is, was POM or PTFE?

[@yt.myworks]

Hello, I don't remember exactly, I think that was POM.

[@checkwhatsleft4565]

@@yt.myworks I swapped the gasket o ring with new one, same size but it doesn't pump water now, your video after the 9mm o ring was installed, the circle plastic, does that circle plastic with the divot side face the o-ring or the other way around?

[@yt.myworks]

Hello, the circle in the plastic should point to the o-ring. But it should also work the other way around. Check everything again exactly.

[@checkwhatsleft4565]

@@yt.myworks it took me while to find out that it was air pocket in the tube that cause no water.

[@aflanos]

Derlin

[@periklisgiannopoulos5273]

Hi. My coffee machine starts with normal sound but after 2or3 seconds it makes less sound than normal and pour out just drops of coffee. It seems it is struggling when pressure is built. Could that be a pump problem? I have disassemble the pump and it all seems ok although i havent replaced any o ring etc as you advise. Nice video,it helped a lot anyway.

[@yt.myworks]

Hello, that can mean that the o-rings and ball have to be changed or the machine is clogged (calcified).

[@periklisgiannopoulos5273]

@@yt.myworks I wouldn't say so. I do the regular basis cleaning on it and as i said about the pump, it all seems ok.No compounds etc foundings. I will replace parts or the pump itself and see. I will keep you posted about it if you like. Thank you for your response anyway .

[@yt.myworks]

Please follow step 3 from my last video (min. 7:00), maybe that will help. Descaling recommended by the manufacturer is often not enough. kzbin.info/www/bejne/hXu6mKiJnN6ZasU

[@flashkandy]

@@periklisgiannopoulos5273 cleanings or descaling? Big difference.

[@keyvonadelzadeh7043]

@@periklisgiannopoulos5273 hi there. This sounds like my exact problem! Can you let me know what you did and whether it worked?

[@maciejkieb2936]

Hej. Czy pompa wibracyjna moze byc przyczyna bledu "Water CirCuit Empty Fill Water Circouit"? Probowalem napelnic ten maly zbiorniczek gdzie wpada woda przed dojsciem do pompy wibracyjnej, ale nic nie dalo. Plus Pompa dziala dosc glosno.

[@yt.myworks]

Trudno powiedzieć, przeważnie jest głośna kiedy nie dostaje wody. Musisz sprawdzić wężyk po wężyku w którym miejscu jest ewentualnie zatkane. Uwaga! Woda może być gorąca i pod ciśnieniem. O niebezpieczeństwie z prądem chyba nie muszę wspominać.

[@maciejkieb2936]

@@yt.myworks Nigdy nie naprawm urzadzen gdy sa podlaczone do sieci energetycznej :)) Czy Delonghi maja wbudowane zasialanie wewnetrzne oparte na beterii ze o tym piszesz? Czy powod jest bardziej, hmmm, amerykanski? :)

[@yt.myworks]

Oczywiście to drugie ale ostrożności nigdy nie za dużo, już sam się o tym kiedyś przekonałem. Przy szukaniu błędów podłączam zasilanie w urządzeniu wielokrotnie i można się szybko zapomnieć ;-)

[@maciejkieb2936]

@@yt.myworks No u mnie ten blad jest ciagly. Moge jedynie pusic ciepla wode, trwa to okolo 5 sekund. Dwa zauwazylem ze jak w tanku konczy sie woda to nie daje bledu zeby uzupelnic tylko pobiera dalej. Moze ta informacja pomoze w okresleniu co jest nie tak. I dzieki za odpowiedz. Super kanal, przydalo by sie wiecej filmow, szczegolnie z innymi modelami np De'Longhi Eletta, taki jak moj :P

[@yt.myworks]

Sprawdź czy prawidłowo podłączony jest "flowmeter", to te okrągłe, białe urządzenie. Chodzi o kierunek obiegu wody. A z pojemnikiem na wodę to czy pływak nie jest zablokowany.

[@LeGlode]

Thank you.

[@rainerschulteherpsfishes9660]

My red pump marks no resistance in the winding of the coil. Is it burnt?

[@yt.myworks]

@Reiner Schulte: Unfortunately, I cannot tell you that because I have too little knowledge of electronics.

[@helmar242]

Olá, se a resistência é infinita decerto a bobina está queimada.

[@any1ne]

A diode is installed inside the pump. Is that why you think the coil is defective?

[@shareproblem]

good work man or woman :D

[@0704Tommy]

2:20 what are the dimensions of the spring?

[@yt.myworks]

Tamás Kasza: Ø 12,85 mm x L: 18,30 mm x 1,16 mm (All data is without guarantee ;-)

[@0704Tommy]

@@yt.myworks thank you :)

[@anugrahyulianto_]

I have same problem. I have Delonghi Magnifica S, and the water doesn't come out when I try to make coffee. it appears 3 red symbols and that means the coffee is too fine and the water can't come out. However when I try to descale it, the steamer wand and coffee sporut can deliver dirty water. Unfortunately, descaling process stop in about 5 minutes. I am frustrated with this condition. Would you give me the advice to repair it? I am not sure the problem is the pump oring or the sprout oring which is in the front of the machine. I watch several videos that told the problem is in the sprout oring. Because when I try to descale and make coffe, the water leaks to ground coffee tray. Would you give me advice or solution?

[@awakeholic]

Had the same, replaced the pump, sensor and o ring and now it works great again. Don't know which exact part broke, but it works fine again for 30 bucks

[@c.patricksadowski9959]

Where do you think I can get the entire plastic replacement that goes through the pump?

[@kevinalderton1225]

Aliexpress

[@guadalupecarbajal2612]

Hola si me pudieran informar precio y lugar para comprar la bomba completa soy de mexico

[@yt.myworks]

Hola, busque "Ulka Pumpe" en amazon.de o ebay.de y preste atención al nombre correcto de su modelo. El enlace también se puede encontrar a continuación en la descripción. No puedes comprarlos en México?

[@noureddinekoubrit5370]

Bitte um Hilfe : meine delounghi magnifica s arbeitet einwandfrei beim Kaffee machen mit Kaffeepulver aber mit Kaffeebohnen zeigt im Display kaffeeausatz fehlt . Was könnte sein. Danke im Voraus

[@yt.myworks]

Hallo, kannst du bitte diesen Fehler etwas genauer beschreiben? Wie viel Kaffee wird bei Verwendung von Kaffeebohnen gemahlen?

[@noureddinekoubrit5370]

@@yt.myworks ich schließe die Machine mit dem Strom an . Geht normal an , ohne Meldung oder so , sobald ich auf Kaffee mit Bohnen drucke leuchtet im Display kaffeeaufsatz einsetzen obwohl es drin ist , natürlich bleibt die Machine blockiert bis ich sie mit Strom trenne , im Gegenteil wenn ich auf Kaffee mit Pullover drucke funktioniert einwandfrei ohne Meldung

[@grapesofwrath1984]

Where can we buy that O-ring? And the ball?

[@yt.myworks]

amzn.to/3SCGFpL

[@wienerurgestein9800]

Ich hätte eine Frage,meine DeLonghi Magnifica S Plus zieht kein Wasser. Heißwasser auch nicht. "Habe sie geöffnet und seh,dass der Wasserschlauch seitlich kein Wasser zieht. Am Display steht Wasserkreislauf füllen" od. so ähnlich. Nun habe ich mir Ihr Video angesehen und frage mich ob bei der selbe Defekt vorliegen kann. Ist eine Maschine v.2020 mit der selben Wasserpumpe. Hätten Sie vielleicht Ahnung ob es der selbe Defekt ist oder kann es auch was anderes sein. Hmm. Auf eine Antwort würde ich mich freuen.🎄🎉.

[@yt.myworks]

Ich denke nicht dass die Wasserpumpe nach zwei Jahren defekt ist. Ich vermute eine Verkalkung in einer der Teflonleitungen. Das ist zumindest der häufigste Fehler. Meistens ist diese von außen zu erkennen wenn die Schläuche nicht mehr durchsichtig sind.

[@wienerurgestein9800]

@@yt.myworks Oja die Schläuche sind schon noch durchsichtig,vielleicht ganz leicht gelblich. Im hinteren Schlauch der vom Wassertank kommend , sieht man das Wasser in dem sich kleine Luftbläschen leicht hin u. her bewegen, aber es wird nicht weiter transportiert. Daher ist mein Gedanke auf die Wasserpumpe gefallen. Momentan sind über 7000 Café´s gemacht worden.lt. Zählwerk. Ich filtere Brunnenwasser mit einer Laica Tisch - Wasser-Filter Kanne . Es besteht kein anderer Wasserzugang. Zeitweise nehme ich auch gekauftes Wasser. Wäre schön wenn Ihnen vielleicht noch was Einfällt was es sein könnte. Schönes Wochenende gewünscht. Und danke für die schnelle Antwort. Sehr nett.💐 Schönen Gruß aus Wien - Umgebung.

[@yt.myworks]

Hallo, ich habe die ganz dünnen Schläuche gemeint aus Teflon. Diese verstopfen sehr schnell. Okay bei 7000 Kaffees kann natürlich auch eine Wasserpumpe kaputt gehen. In diesem Fall ist es keine schlechte Idee als erstes die Pumpe auszutauschen.

[@mariobrosstellacci9794]

E sufficiente cambiare solo la guarnizione???

[@yt.myworks]

Se la sfera non è troppo piccola (circa 4 mm), è possibile sostituire solo l'o-ring.

[@35g37g]

Mogę zapytać czym został przyklejony Klixon?

[@yt.myworks]

Zwykły pistolet i klej na gorąco.

[@35g37g]

nie musi być nic termoprzewodzącego?@@yt.myworks

[@35g37g]

nie musi być nic termoprzewodzącego?@@yt.myworks

[@troydaboyzzz]

Hi there... Is it my pump that's broken... I get through to the end of de scale.... then it won't pump water... says water circuit problem? 😮‍💨

[@yt.myworks]

Hi, does the water pump become quieter? If so, then a water hose is probably clogged.

[@troydaboyzzz]

@@yt.myworks no the pump doesn't come back on... when I push the ok button.. it just clicks on and off..(solenoid) it happend right at the end of the descale.. But one thing I did try was filled the distributor and I turned machine back on.. the pump struggled for a bit than started working... So I started de-scale again.. and at the same last rinse on de-scale... no pump.. only clicking of solenoid when I keep pushing ok on screen 😔

[@yt.myworks]

You have to test the water pump by disconnecting the teflon hose after the pump. You can put the end of the hose in a bottle to see if water comes out. But be careful, the machine is live!

[@troydaboyzzz]

@@yt.myworks thanks I will definitely try.. appreciate your time and knowledge 🥰

[@JesusLoveToSkate]

Thank you so much!!!

[@paulkamphorst5290]

thanks for de video

[@landonkey3402]

I wasn't careful and tore the hose that you removed @1:00. Can you help me find the replacement part?

[@yt.myworks]

www.ebay.de/itm/291901388175?mkcid=16&mkevt=1&mkrid=707-127634-2357-0&ssspo=AQmADgC_SHO&sssrc=4429486&ssuid=fqjNmJj7Q9S&var=&widget_ver=artemis&media=COPY

[@yt.myworks]

amzn.to/44QXa5e

[@ellenphilpotts-troy2098]

Sir, my coffee machine when turn on power active instantly the water pump what can it be?

[@yt.myworks]

I don't know exactly, but it could be that the electronics are broken.

[@Коля-х6я]

Поломка

[@adredy]

in my opinion those pumps are not goor for normal tap water thats why they dying so fast :/ i also have issue but with steamer or i dont know brita filter do not use tap water they last longer

[@scottjcole]

Does anyone know where I could buy a replacement plastic ball (the valve ball)?

[@yt.myworks]

amzn.to/3c98AWz

[@ci5366]

Can you please let me know rom where to buy oring and ball . Thanks

[@yt.myworks]

amzn.to/3V8fT9k

[@Коля-х6я]

И зачем ты это рпзобрал тут всё исправно. Ты просто супер чудо.

[@viktoriaschneiderneszente6528]

Dankeschön 👍

[@revinobable]

where to find a replacement ball?

[@yt.myworks]

Please search on Amazon or eBay. See my link below in the description.

[@jevgenijchebotariov3799]

can anyone help me with advise, descaling cycle would not finish, water comes only through milk section during descaling cycle, when machine tries to descale middle nosils no water coming out, so machine runs descaling cycle for ever .. when water runs out it resets it self and asks to run descaling cycle again.. any advise appreciated

[@mukimj82]

wirklich nur diese kleine Dichtung???

[@yt.myworks]

Ja, mehr ist nicht, eventuell noch die Kunststoffkugel falls verschließen.

[@mukimj82]

@@yt.myworks wo bekommt man die Teile her..??bei mir kommt nur heiße Luft seit einer Woche..hab ganze Pumpe bestellt kommt am Donnerstag..ich hoffe Kügelchen und Feder ist dabei

[@yt.myworks]

Neue Wasserpumpen sind i.d.R. einbaufertig.

[@mukimj82]

So hab das Teil heute über Amazon für 17eu bekommen..eingebaut und läuft wie damals..vielen dank

[@hallohallo586]

Du schreibst 9mmx5mmx2mm o-ring, was meinsd du mit 9mm ?

[@yt.myworks]

Das sind die Aussenmaße 5+2+2=9

[@szejker1989]

Pompka Ulka EP5 w ESAM 3000.B. Bardzo słabo podaje wodę, przy czyszczeniu ekspres najpierw prycha i cyka jakby jakiś zaworek nie mógł się do porządku otworzyć. Woda cofa się po jakimś czasie z rurki między pompką, a bojlerem. W internetach są zestawy naprawcze czyli oring i kulka. Ale dlaczego nie ma grzybka? Na filmikach na YT nikt nie rozbiera elementu z grzybkiem, a jest on tak samo sparciały jak oring przy kulce. Pozostaje wymiana pompki na nową?

[@yt.myworks]

Przyznaję się że też jeszcze nie wymieniałem grzybka na nowy. W nowszych modelach chyba ich nawet nie ma. Najważniejszymi są jednak uszczelka i ewentualnie kulka które należy wymienić. Sprawdź następnie czy nie jest w którymś miejscu zatkany przewód wody lub sam bojler. Często pojawia się w tych miejscach kamień kotłowy. Włącz płukanie z roztworem odkamieniającym co parę minut.

[@szejker1989]

@@yt.myworks Ekspres z drugiej ręki, rok temu czyściłem wyciorem wszystkie przewody, wymieniałem uszczelki w zaparzaczu i elemencie który wciska się w zaparzacz oraz przewodach od bojlera do zaparzacza. Przez dwa odkamieniania wypadały duże grudki kamienia, teraz jest już spokój, odkamienianie robię często, ustawiłem sobie że mam najtwardszą wodę (muszę sprawdzić z ciekawości jaką faktycznie mam, wodociągi, nowy dom i nowa nitka wodociągowa na mojej ulicy). Zauważyłem natomiast, że po kilkunastu godzinach nie ma wody w przewodzie między pompką, a bojlerem. Na logikę, chyba woda powinna być cały czas, może puszczają oringi na przewodach lub wspomniany przez ciebie oring w pompce? I chyba przez to jest taki efekt po włączeniu ekspresu: syczenie, prychanie, bulgotanie, para, dopiero chwilę później zaczyna lecieć woda i zaparzanie kawy jest OK, a z każdą kolejną kawą jest lepiej. Potwierdzasz, że woda nie powinna się cofnąć z przewodu między pompką, a bojlerem? Mógłbyś mi polecić jakiś dobry, sprawdzony odkamieniacz? Zamierzam wymienić całą pompkę na nową ponieważ cena jest śmieszna ;) wymiennego grzybka nie potrafię znaleźć, a jest już twardy jak ten oring przy kulce.

[@yt.myworks]

Jeżeli słychać syczenie to przypuszczam że będzie gdzieś nieszczelność w górnym tłoku zaparzacza. Wtedy dostaje sie powietrze i woda wędruje z powrotem do zbiornika. W tym przypadku można wymienić uszczelki lub całą część na nową.

[@mydc2200]

How to repair the pump if the coil broken? My pump is ceme ulka not ulka

[@yt.myworks]

You have to look for used parts. There are no spare parts for the pump :-(

[@any1ne]

A diode is installed inside the pump. Is that why you think the coil is defective?

[@mydc2200]

@@any1ne i have already replaced with new ulka pump, it worked now

[@untitledduck9675]

Ball size please and the big o rings

[@michaeltb1358]

I can never understand why anyone uses an electric screwdriver to dismantle a small appliance. Saves a few seconds but so much risk of damaging plastic threads.

[@formbi]

you won't really damage them with unscrewing

[@Egorov242]

At this pomp metal threads

[@izzzzzz6]

I tried sanding the outer rings till they fit very easily. I did not prime the pump with a syringe so perhaps that why i wasn't seeing results? I'm also wondering if it might be the small O ring and although it looks ok perhaps it's stretched, it's not that easy to get it to seat in it's groove. I'm going to try again tomorrow. Too late now. I have a box of green O rings, one may fit.?

[@mrgarrisonshat]

Quick question, I have taken out the pump from the Delongi ecam series as the machine stopped putting out water. When the hot water button is pressed water comes out OK. I took apart the pump and put it back together and the same issue is there. Is there any other reason why the water would not come out ? Thanks in advance.

[@MattFixesStuff]

Did you also test the pump ? Make sure it works by itself. Also some pumps have fuses infront of them (You can see them at the wires that go in the pump. Measure the fuse too.

[@ЮрийГоловко-ъ6в]

10 000 like!!!!!the ball has evaporated.I didn't know where to put it correctly😃😃😃

[@lwyr9152]

My concern is that your EPDM o-ring is not food grade.

[@nikirobbins4813]

Hello I have one of these machines, and water no longer comes out anymore at all. tried everything. The pump doesn’t seem to be making any noise either. Only a very small hum. Steam still comes out of the wand though. Just asking an opinion if you think it’s the pump for sure, or if there’s a blockage somewhere?

[@yt.myworks]

I would check for blockage first. Most of the time, the pipe that comes out of the heater is affected.

[@nikirobbins4813]

@@yt.myworks just left it on for a little bit and it magically started working again. Strange. Gonna descale it a couple times, and hope for the best. Thanks for the quick reply.

[@goozoon]

@@yt.myworks Also, just replaced the o-ring and the ball. And only few drops came out. But steam/water is working. Which pipe is that, please? Maybe use stronger decalc solution? Thank you

[@yt.myworks]

@@goozoon this is the pipe that comes straight up from the heater. Most of the time the calcification is visible when the inside of the pipe is white.

[@goozoon]

@@yt.myworks I have two Magnificas and in first i changed the o-ring (i described here) and nothing changed. So i saw your another video and tried to decalc with rinse technique (my in-built decalc process pushes water only via vaporises head only, not via coffe makes nozzles, so it decals only that left pipe only. This i have on both machines, i dont know why) So i put some concentrated decal solution and made rinsing as you described. And after 3 rinse all is good now. I made the same on second machine, without changing o-ring and it makes coffee now as it should. Thank you. First machine is leaking water from tank when making coffee or rinsing. No leak when doing nothing. So need to check the valve on the tank. Maybe calc, too

[@koto6a3a]

Фантомас

[@abdoelmajid2371]

👍

[@user-xu6fp7je3u]

Тогда уж и шарик надо было поменять

[@richardgrzesiak708]

Merci !

[@untitledduck9675]

you can buy glass balls

[@PiotrGromulski]

Czy mogą być jakieś inne objawy uszkodzenia pompki poza tym że nie pompuje w ogóle wody lub pod za małym ciśnieniem ?. U mnie woda idzie dobrze ale wydaje mi się że po skończonej pracy zaczyna "bzyczeć", myślałem że te dźwięki idą z silnika młynka bo jest tuż obok ale jego wadę wyeliminowałem bo to chyba jedyny element który może nie pracować przy robieniu kawy. Bzyczenie jest wtedy gdy ekspres nie mieli kawy i nie tłoczy wody. Czy jakiś inny element np podgrzewacz wody może takie dźwięki wydawać ?, wszystkie te elementy są tak blisko siebie że trudno stwierdzić skąd idzie hałas.

[@yt.myworks]

Na pewno wszystkich objawów jeszcze nie ogarniam, tak że wszystko jest możliwe. W DeLonghi raczej nie ma już innych elementów które mogłyby wydawać dźwięki. No chyba że zaworek elektromagnetyczny o ile jest zabudowany.

[@PiotrGromulski]

@@yt.myworks Spoko, kupiłem ulke to dziś zmienię i zobacze czy hałas zniknie.

[@TopCutCNC]

I have this problam 😢

[@NYCgoblue]

Hi. I have been trying to fix a Jura S9. Water is not coming through the pump. Water is not even getting to it. Can you tell me if the problem is the pump from this video? You can hear the sound of the pump trying to work. kzbin.info/www/bejne/bWaUd3-BhZKNeqs

[@yt.myworks]

Hello NYCgoblue, I think the pump is broken. To be sure you can connect it to 110V. ! BUT BE CAREFUL WITH ELECTRICITY! If the pump still doesn't work you have to buy a new one. Lg myworks

[@veles566]

Зачем перчатки? Болеешь

[@AaaAaa-oj7jx]

Горе мастер , затягивает болты электроинструментом без момента затяжки. Кошмар

[@1001awab]

It looks like the work of a pervert but he is doing a great job. Silence of the lambs come into my mind

[@yt.myworks]

Peter Kaiser: Zu viele Filme schauen tut offensichtlich nicht gut 😉

[@wienerurgestein9800]

👍