DESMI Overhaul video NSL Centrifugal Pump NSL 200 265 14

  Рет қаралды 10,068

DESMI

DESMI

Күн бұрын

Пікірлер: 11
@christianjaypellazo1062
@christianjaypellazo1062 Жыл бұрын
Thank you much for your videos. I learn so much
@ajeetsingh9196
@ajeetsingh9196 6 жыл бұрын
Love to watch this. Good 4r learner.
@AbdullahKhan-wt8kd
@AbdullahKhan-wt8kd 2 жыл бұрын
Which type soap or soapy water you are saying here this is special or manual made plz reply according
@karthikmenon3580
@karthikmenon3580 9 жыл бұрын
Can you please talk about the wear ring.. And how to check the clearances Thanks in advance
@DESMIAS
@DESMIAS 9 жыл бұрын
Karthik Menon Dear KarthikIn our overhaul videos our Service Technician shows how to disassemble the pump, replacing all parts which we normally recommend to replace and then assembly the pump again. All the parts that are used for the overhaul are included in our DESMI spare parts kit with genuine spare parts. The wear ring and the impeller are not parts that normally have to be replaced. Therefore it is not shown and mentioned in our overhaul video. But if you want to check the clearance between the impeller and the sealing ring, the answer is max 0.4-0.5 mm. measured in radius. This information you can find at our after sales section at www.desmi.com/aftersales (manual T1380 for NSL in Monobloc design). At our after sales section you can find manuals, spare parts kits, videos etc. Trusting above is informative, if not please do not hesitate to contact us. Wishing you the best of luck. Best regardsDESMI
@karthikmenon3580
@karthikmenon3580 9 жыл бұрын
DESMIAS Thanks a lot Could you possibly explain the use of water deflector.. Your reply was really helpful.
@DESMIAS
@DESMIAS 9 жыл бұрын
Karthik Menon Of course :-)The water deflector also called V-ring has the function to prevent media from a leakage from the shaft seal entering the bearings.Hope this is helpful. Otherwise please do not hesitate to get back to us.Best regardsDESMI
@darkness4382
@darkness4382 6 жыл бұрын
Measure the ID on the case or cover, then measure the OD on the impeller, the difference is your clearance.
@samk517
@samk517 Жыл бұрын
How to know its motor overhaul? also want to how to request spare parts for motor (type DESMI 3D2 315M 4)
@DESMIAS
@DESMIAS Жыл бұрын
Hi Sam - please write to spareparts@desmi.com and they will assist you with spare parts etc. 🙂
@hridoymahmud6307
@hridoymahmud6307 4 жыл бұрын
Wow
DESMI Overhaul Video GP66 ROTAN® Gear Pump
11:45
DESMI
Рет қаралды 7 М.
$1 vs $500,000 Plane Ticket!
12:20
MrBeast
Рет қаралды 122 МЛН
DESMI Overhaul Video HD 101 - ROTAN® Gear Pump
13:18
DESMI
Рет қаралды 20 М.
DESMI Overhaul video Modular S 100 80 220N
11:30
DESMI
Рет қаралды 9 М.
Mechanical Seal Failure & Troubleshooting
10:33
Paul Brimhall
Рет қаралды 227 М.
DESMI In-Line DSL Centrifugal Pump - Vertical, Double Suction
2:44
HVH Industrial Solutions
Рет қаралды 10 М.
Pumping Machinery, Stuffing Box, Bearings and Packing Seal
18:17
DESMI ROTAN HD - Internal Gear Pump
3:25
HVH Industrial Solutions
Рет қаралды 453