DHCP Relay| Vlan DHCP| how to create pool in cisco

Cisco configuration DHCP Relay, Create Pool for Vlan
DHCP Relay
1. Create VLan
CoreSW(config)#vlan 10
CoreSW(config-vlan)#Name Server
CoreSW(config-vlan)#ex
CoreSW(config)#vlan 20
CoreSW(config-vlan)#Name IT-Dept
CoreSW(config-vlan)#ex
CoreSW(config)#vlan 30
CoreSW(config-vlan)#Name HR-Dept
CoreSW(config-vlan)#ex
2. Set IP address on all VLan
CoreSW(config)#int vlan 10
CoreSW(config-if)#ip add 192.168.10.1 255.255.255.0
CoreSW(config-if)#no shu
CoreSW(config-if)#ex
CoreSW(config)#int vlan 20
CoreSW(config-if)#ip add 192.168.20.1 255.255.255.0
CoreSW(config-if)#no shu
CoreSW(config-if)#ex
CoreSW(config)#int vlan 30
CoreSW(config-if)#ip add 192.168.30.1 255.255.255.0
CoreSW(config-if)#no shu
CoreSW(config-if)#ex
3. Configure Trunk Port and VTP Server (CoreSW, ACSW-01, ACSW-02)
CoreSW(config)#int range f0/2-3
CoreSW(config-if-range)#switchport trunk encapsulation dot1q
CoreSW(config-if-range)#switchport mode trunk
ACSW-01(config)#int f0/1
ACSW-01(config-if)#switchport mode trunk
ACSW-02(config)#int f0/1
ACSW-02(config-if)#switchport mode trunk
CoreSW(config)#vtp mode Server
CoreSW(config)#vtp version 2
CoreSW(config)#vtp domain cisco.com
4. Asign Port to all VLan
- On CoreSW f0/1 ( VLan 10)
- On ACSW-01 f0/2-3 (VLan 20)
- On ACSW-02 f0/2-3 ( VLan 30)
CoreSW(config)#int f0/1
CoreSW(config-if)#switchport mode access
CoreSW(config-if)#switchport access vlan 10
CoreSW(config-if)#ex
ACSW-01(config)#int range f0/1-2
ACSW-01(config-if-range)#switchport mode access
ACSW-01(config-if-range)#switchport access vlan 20
ACSW-01(config-if-range)#ex
ACSW-02(config)#int range f0/1-2
ACSW-02(config-if-range)#switchport mode access
ACSW-02(config-if-range)#switchport access vlan 30
ACSW-02(config-if-range)#ex
5. Enable DHCP Server on Server
6. Configure DHCP Relay On CoreSW
CoreSW(config)#int vlan 20
CoreSW(config-if)#ip help
CoreSW(config-if)#ip helper-address 192.168.10.254
CoreSW(config-if)#ex
CoreSW(config)#int vlan 30
CoreSW(config-if)#ip help
CoreSW(config-if)#ip helper-address 192.168.10.254
CoreSW(config-if)#ex
7. Enable IP Routing On CoreSW
CoreSW(config)#ip routing

[@rochefiesco6022]

Thank you very much for the video. No voice, but well explained. Honestly did able to learn about it. Thank you again.

[@EXTechnical]

Thanks for watching

[@al9b7i24]

Video wonderful music name

[@rajwantkaur6841]

hello i need your help how can i contact you