Diesel Generator Valve Adjustment

www.AuroraGenerators.com
Adjusting the vales is required maintenance on all portable diesel generators. The first adjustment is required at 25 hours. They should also be checked every 200 hours. If you fail to do this, the valve adjustment screws can break.
The whole process takes no more than 5 minutes and this video shows how it is done.

[@Mikesorrento3344]

You really need to remove engine pull start shroud (4 bolts) to determine top dead center. TDC is marked on flywheel by a hole Then adjust valves to .15 mm gap

[@chandimakohombange9226]

thank you so much for this clear video.nicely explained

[@jeetuyadav8627]

chandima kohombange sir apke pass ye engien hai kya .pls call me 7428289277.

[@papz8977]

nice and clear but there is a little doubt why not test after doing tappet..😁 but still i like the way you do while explaining its purposes..nice thumbs up

[@konradmurzyn7072]

Thank you for this video! I hope also it's should be the same procedure and valve settings for my F192FB Diesel Power Generator as it from your video! Thanks Dude!

[@clydemcpherson613]

Thanks for the video i hipe it work in my L186

[@prathapjg898]

Tnqq so much sr..

[@joshsundiwa]

nice voice over thank you

[@delynnaddams8774]

What about positioning past TDC compression release valve on the intake, only? Does this unit have that? Thanks

[@sumanmondalsuman7635]

Thanks uncle and good work

[@michaelbirchall2247]

My exhaust is blowing out flames and has melted the flexible exhaust connector. The valve clearances are good. Why would the valve be opening when there are flames still in the cylinder?

[@johnbaggus9966]

Where to buy the little pcb that has the oil light connected to it ,

[@charlieamican233]

Sir what is the clearance of each valve?

[@etiennekalomwe5255]

Très bien very good

[@johnnytotheworld4802]

what will happen if the gasket for the rocker cover is damaged?

[@tobiaswittenmeier1877]

A little bit of oil may leak out.

[@antedadic6382]

lol

[@teejays2553]

'Hylomar Blue' will sort it.

[@robinmicheli7297]

You say .15mm gap but video shows feeler gauge .011Inch or .279mm a but confusing what is the correct gap???

[@cloroxbleach8676]

0.10-0.15 MM

[@oramasdj]

Hi, What type of oil does the 186fa engine use?

[@ottomartinez4896]

Dear Sirs I have the same generator. Could you please tell me what is the gap ?

[@kriswright1022]

.006”

[@JM-yx1lm]

.11 like his feeler guages are not showing

[@minyongalariaofernando7527]

Could you please tell me what is the gap?

[@mustafaar7899]

How you know this tdc

[@CuongBui-uu3vj]

Mình có cái máy phát yanmar động cơ l60 khi tải nặng ra khỏi nhiều màu đen có phải hỏng Kim phun không

[@darlingguadaluperivero8712]

Si la valvula esta muy cerrada funciona el motor?

[@Fsam87]

No debe ir 15mm admisión 20. Escape asi lo hacen en la honda

[@pahmaadisaputra905]

Mesin sepeti itu apa dimana lobang ventilatornya?

[@SKGAMERSr1]

Yah engine kis company ka hai parts lena hai

[@basdol]

Gap intake 0.11 and gap exhaust 0.15 ?

[@niyigenaoligene5627]

Why gen kipol knok on exhaust valve and bring fraish combustible

[@SunilSingh-fd1uk]

How much horsepower it is

[@roland349]

8,8 hp

[@agyf4581]

ممتازجدا نرجوالترجمه بالعربي

[@bisratchebsi3239]

Add a public comment...thank you so Much

[@agyf4581]

ممكن الترجمة عربي

[@MrMax31kk]

Rocker adjustment screw is lose not tight perfact -

[@malikrameez703]

Sir engine won't start what are it's effects

[@midomedo8451]

اريد رقم هاتف للتواصل

[@agyf4581]

770983194 اليمن

[@paulhancock3844]

Love the the protective foot ware, flip flops FFS!

[@faustomora9300]

Q 6

[@shehzadbhatti5893]

these diesel gen r nt helpful beacuse there piston case or block is made wiht alomonium

[@m8onethousand]

I've had one for over 5 years abusing it. it ran over 12 hours (sometimes 24+ hours) a day for 5 months straight and it's still pretty much brand new. running a/c's, microwaves, computers, tvs, and even saws and welders. these little things can take more abuse than people think.