Diesel Service Truck Life Doing Brakes on Hino Box Truck

[@azizapritchard5546]

Thanks, good job.

[@pedroacosta2199]

Thank you men for the video, from Montreal, in Canada!

[@USA.Muslims]

Thanks for showing all

[@richardjavier4188]

Nice id like the way its explain and keep up the good work..

[@rottihavr1]

Are you based in Florida? Love your in depth videos! I need a mechanic for my Hino in Orlando..

[@ZepolWorkzGarage]

@@rottihavr1 I'm based in Tampa Florida. Hit up my email [e-mail]

[@abdorouiss5279]

Well done !!

[@Sinner1120]

Love the videos, keep it up!

[@artlopez9617]

I liked the video! 💯🤙👍

[@monkeyzulu]

Good job

[@jessiefitchett5354]

Do you have a video for the front brakes on a 2016 Hino

[@ZepolWorkzGarage]

@jessiefitchett5354 no I don't have one it's about the same. Springs little different design. If I get a chance I'll try make video on steer brakes.

[@kingb5362]

Nice

[@tyronebarnett6695]

Very nice 👍

[@kylerich3771]

That was a gr8 video! Was that a hino 338 in your video? 😁kyle

[@ZepolWorkzGarage]

Yes truck was a Hino 338.

[@kylerich3771]

@@ZepolWorkzGarage Greatly appreciate your help & kindness🙂 I just bought a 338 in Boston & drove it to the west coast ( just cab chassis) . I changed the oil behind a harbor freight in new Hampshire. The oil plug was so tight a 3/8 breaker bar wouldn't get it & I'm not a Lightfoot I weight 245 pounds & I'm fairly strong. I had to go back in harbor freight and buy a 2 foot long 1/2 drive bar and it was still pretty tuff and I even hit it with pb blaster🤣

[@ZepolWorkzGarage]

@@kylerich3771 that's why I always have a 3ft pipe to slide over breaker bar for more leverage. Thanks for Comment keep wrenching.

[@kylerich3771]

@@ZepolWorkzGarage Amen & take care😁

[@zeekedd6245]

Can you do a video on the front wheel aswell

[@ZepolWorkzGarage]

The front brakes go on the same way just a smaller brake shoes.

[@thegreekguyviva-greece5881]

stupid but kinda important question... we have the 268 hino also. done the air brakes everything else BUT I've never done the engine or frame fuel filters... this truck has a lift pump right? changing the fuel filters just full em up, do a key on off cycle like5, 8 times and start her up??? theres no manual priming pump like old school trucks?

[@ZepolWorkzGarage]

the greek guy viva-greece yes should have electric lift pump. Does yours have Davco type fuel water separator I fill those full fuel also. I do same key on and off couple times. When cranking hold throttle pedal to the floor until engine starts. Then keep revs around 1500 till running smooth should have no air in fuel system.

[@thegreekguyviva-greece5881]

@@ZepolWorkzGarage yes has that Davco type filter also.. thank you... was not sure cuz our kenworth doesnt, it has a primer pump.... THANK YOU!!!!!!

[@terrellscaife2411]

So what if you use liquid wrench

[@ZepolWorkzGarage]

Liquid Wrench is good it is a penetration spray. WD40 is a water dispersing spray. There both ok as long used for what made of.

[@tahirforever6926]

How much it cost to fix in both tires on both sides ?

[@ZepolWorkzGarage]

Have to call tire shop for prices.

[@Alchemist1on1]

More videos

[@MottyRuttner]

are they the same on 338 truck 2005-2013 years?

[@ZepolWorkzGarage]

Yes the rear Brakes are the same on those years as well.

[@monkeyzulu]

Thats how i do it lot easy

[@thereisnogodbutallahswt1320]

Tbose Those brakes dont even kook look low

[@ZepolWorkzGarage]

Abdullah No Last Name You have to look at lower shoe was almost at 1/4 and Customer didn’t want chance it till next Pm. DOT Shut you down quickly and start looking at other stuff.

[@miloudelfarh6302]

Good job

[@ZepolWorkzGarage]

Thanks 🙏🛠🧰💯