Diode Laser master jig Longer 5 Ray Easy to build Will save you hours

Laser Master Jig - Part One How to align a Honeycomb bed to your laser frame. Once done you can install and line up your Honeycomb bed in seconds knowing that it is square to the frame.
In this presentation I install the main BASE of my Master Jig. Once done correctly when we come to part two, creating the jig panels, its so easy and done in a few minutes.
The Blank JIG FRAME can be cut on the honeycomb bed to avoid flash back. When you come to cut in "INTERNAL" section of the JIG PANELS they MUST be cut when connected to the MASTER JIG BASE. This will ensure perfect alignment.
I will include BLANKS for the files to make the actual JIG PANELS. These will be various sizes.
I welcome any comments upon this design, If you see where an improvement can be made, I may include it in any future update.
IT takes a small amount of your time to get the base and the Honeycomb located but the every time you it, its aligned in seconds.
Files can be found here:- ko-fi.com/s/ad9a587a60
The files contain the MASTER JIG as shown in this video and samples of the JIGS that fit into the BASE JIG.
*****************************************************************************************************
If you have found this video useful please consider if you are able to TIP me using the link below. I love my coffee it keeps me going
ko-fi.com/flixmyswitch
*****************************************************************************************************
Check-out my other Playlists
Video list as at 19/06/2024. I post frequently
1. Safety • diode laser safety, No...
2. Build your laser square, eccentric nuts • diode laser frame asse...
3. Remove stiff wiring • diode laser frame asse...
4. Air assist pump noise • Laser air assist pump ...
5. Laser correct focus • diode laser longer ray...
6. Diode laser project update parts and tools • diode laser mailbag te...
7. Diode Laser project updates parts, laser pointer air assist testing tools • Project updates Z lift...
8. Lightburn Cut Palette and Arrange Long • LightBurn menus missin...
9. Cold temps laser not working • using a laser in cold ...
10. laser bed matrix waste board • laser bed matrix on wa...
11. Lightburn amazing online free file generator • Lightburn Amazing Onli...
12. LaserGRBL amazing online FREE file generator • Lightburn Amazing Onli...
13. Laser focus height gauge • laser height gauge foc...
14. Laser taller legs for better access, front loading, easy clean up. • Longer Ray 5 Thin legs...
15. Lightburn Possible material test fire safety issue • lightburn 1 5 material...
16. Laser wifi, static IP WEB UI $ commands • Wifi, static IP, how t...
17. Better height adjustment. • Better height adjustme...
18. Smooth Slider Easy focus and maintenance. • Longer Ray5 Laser smoo...
19. Watch YouTuce videos with your own language as subtitles. • KZbin Video Subtitle...
20. Laser extract duct PVC vs smooth bore metal. • Laser extract hose duc...
21. Laser work holding position system. • Jigs Work Holding Posi...
22. Laser honeycomb bed make sure its square. • How square is your hon...
23. Laser firmware update. • Longer Ray5 Laser firm...
24. Lightburn 101, two point rotate • Lightburn two point ro...
25. Longer Ray5 Master Jig. • Diode Laser master jig...
26. Longer Ray 5 master Jig Cutting the Blanks. • The master Jig - Cutti...
27. Swivel cable mounts. • Swivel cable mounts Lo...
28. Subscribe not to miss the next video.
Music by: www.bensound.com​
FlixMySwitch all about the stuff I like doing.
Always do you own safety research. This video is made for your enterainment. FlixMyswitchLaser can not be held responsible for any damage to your laser machine, materials, cloths, eye sight, property, your own or others health. Always wear correctly rated eye protection. These laser are not toys, there is a real risk of fire, always have a water spray bottle and Co2 fire extingusher at hand. Never leave your laser unattended.

[@FlixmyswitchLASER]

It's very important that the gantry is square to the frame. I have covered this in other videos. If you ever have your stepper motors grid / miss steps, like when the head crashes into the side of the frame, and your stepper make a strange loud noise like gears grinding, you would need to check your gantry squareness again. Its an easy process which I have covered in two videos. See videos 2 and 22

[@iq0099]

you should have the frame perfectly 90 to itself not the lower frame.. So you ensure the laser move in exact90 to itself.

[@FlixmyswitchLASER]

Absolutely. I have covered squaring up the frame and your honeycomb bed in other videos. To square up my frame I used tin foil