Dirt Bike Washing Done Right!

[@-PlayMaker-]

This is the most in depth cleaning and maintenance routine on KZbin. Your literally the all-knowing of dirt bikes lol

[@dirtbiketv1]

Thanks!

[@BrandonLund]

I like your methotical way of doing things and the scrubbing bubbles is a nice tip. I'm always interested in seeing how others do things. I too like to keep my stuff pristine and ready to go at a moments notice. Thanks again!

[@jacksonclark1684]

You completely changed how in depth I go to keep my bike maintained. This was really helpful thanks man

[@dylancrow7919]

Taping the intake is such an underrated tip. Every time I went for a ride, I would come home and wash the bike. I would avoid spraying directly into the intake but probably got more water in there than I thought. I would have so much trouble getting the bike started and be worried I was losing compression or getting my carb dirty. This last time I taped up the intake before I washed it, and it fired right up so easily. I’m going to cut myself some foam plugs to fill the holes during washing.

[@734enduro]

I use my leaf blower to dry off the bike. It works good for me. As always thanks for the video!

[@paul.vanhout57]

Nice bike cleaning method. I generally remove the seat and replace the air filter with a cover before washing. Your garage is proof that the right number of bikes is one more👍

[@thanedavis1273]

I use a cordless leaf blower to blow the water off after riding.

[@thanedavis1273]

after washing.

[@deleaton4523]

Jay, I followed your advice. Set my stopwatch, got out the pressure washer (mine wasn't as ready as yours), washed the bike, wiped it down, replaced the skid plate, put the pressure washer away, and it took 30 min. Thank you. Del

[@Natedoc808]

I use a dewalt power washer (550psi) not a pressure washer 1500+psi, tail piper plug and air filter cover with filter usually going into the Twin Air cleaning tub. I use something called Oil Eater (citrus based, by the gallon at Tractor supply or Zep surface cleaner diluted 50%). Once the detergent has had a few minutes to loosen up the junk (typically when I put my air filter in cleaner tub), I take a big bottle brush for car wheel cleaning and get into the nooks and crannies between surfaces of the engine and chassis including linkage/rear spring/shock; if you think your bike is clean then try this after your usual wash and see how much crud is packed where you cannot access easily. I use my leaf blower to dry the bike and compressed air on the chain only but stay away from seals with compressed air as you can drive water past the seal. Once that's done I grab a T Handle and check the bolts, drain the carb bowl, check fluids and top off as necessary so she is ready at the drop of a hat.

[@sanjosejeff]

I use Sc1. “New dirt bike in a can”. Always pull my seat too. About every 5 months, I put die electric grease in every connector and do a loose bolt check every month but that’s really depending type and how often you ride

[@bradleymuha4861]

Do you put dielectric grease in the connector or just around it?

[@sanjosejeff]

@@bradleymuha4861 inside the connector. Pro tip: do it to all Ur tv remotes controls too to keep aaa and AA battery corrosion from ruining them

[@painsrides]

Oh crap!!!!!! what simple but awesome idea...."scrubbing bubbles" .... no more buying expensive cleaners for me ..thx Jay

[@fortgreeneprojects1]

I enjoyed the video and the best way to wash your bike and with proper equipment. I never owned a dirt bike before. I want to get one for myself and my son. Peace and Love NYC...

[@BraaapoholicBob]

Jay, same here accept I do remove the air filter, shove a rag into the inlet just in case, and put a waterproof cover on it...that way I can get a clean airbox. I don't do that every time...use tape sometimes if not too dirty. Only other thing I worry about and so don't use is the pressure washer. In the past I've forced water into bearings...just chicken to use one any more. Scrubbing bubbles...LOL...I have to try that...I have always used a diluted solution of Simple Green.

[@TrickRacing]

Did you do this on your yz 250f? Should i block off intake

[@TheRossillini]

People give me shit all the time for being overkill with stuff like this but I’m glad there’s others that show love and appreciation to there bikes by doin it right.

[@rockbay79]

Very tight organization! Respect!

[@emfl4437]

The tape idea is awesome, thanks for sharing that tip.

[@rcarle]

You are the one that taught me how to properly wash a bike back in the day.

[@marcusm.3486]

I use ZEP Fast 505 degreaser and a magic eraser and it works really really well.

[@user-pp5or5og4k]

Scrubbing bubbles has a polish component to it. Wouldn't that be bad on brake rotors and brake pads?

[@robertwoods2505]

Dang Jay, I didn't have any great expectations for this video but you two killed it. Great job, both of you! PS, your garage is awesome!!

[@thatfast3002]

"That's lame, your bike should always be ready" lol

[@justsendit3217]

All manuals I've seen say don't use pressure washers as they push dirt into seals

[@nastysoda9212]

Thanks! I was never sure of the proper way or what to watch out for. That Yamaha looks so nice!

[@MoreMoto262]

I use Simple Green and a leaf blower, but I'll ride it up and down the street a few times to get some of the water out.

[@sethmacgillivary1281]

Does simple green strip paint

[@MoreMoto262]

@@sethmacgillivary1281 no, I used some other cleaner that did.

[@BlueDawnEnduro]

I can't believe I watched the whole thing. Good job.

[@Turbo_JAM]

Good idea on the blue tape, harder to lose the “to do” list!

[@spencerclark2269]

Thanks for the great techniques and tips. I appreciate them.

[@miro_s]

Won’t the scotchbrite scratch the plastics, if not the frame too? And gosh it only takes 30 min! (For me two hours are barely enough for one bike…😢)

[@ConnorFreeman-o9n]

Washed my bike today and completely forgot about the intake and then went and started it. Didn’t notice anything weird but I’m worried, will it be fine?

[@Ste4433]

Yes you should be fine

[@909ARSENAL]

I figured it out pretty close. Thank you again STAY READY!

[@vaughnwilliams3600]

you are the smartest and best looking guy on the internet lol

[@burtonjnb]

Amazing video! Love your mic. =)

[@myricastillo5097]

I really love these videos jay 🤙 I do every single tip you do and say and they save me time and money 🙂 even saves me from getting hurt when I ride 👍

[@Danielxperez14]

this is a really informative video! i appreciate the tips

[@hobiesmith9370]

great video!!! thank you

[@Backdoorslamfest]

I must ask what kind of ski is that on the floor. Thing looked sweet

[@dirtyhooliganmx4337]

Great video a lot of people don't realize the right way to clean a bike

[@jimmydickson8854]

I never use chemicals to wash my bike as it destroys the wiring connections eventually

[@sxfwilson6603]

Hi what alloy cleaner do u use

[@dirtbiketv1]

Email Jay with questions. Contact info in About tab.

[@johnykryll]

Hey, which footpegs are on the Honda?

[@flashbang243]

I am new to dirt bike riding and find your videos extremely helpful thank you 🇦🇺

[@krrrruptidsoless]

Note tape...cool

[@typrall9028]

Rien de bien révolutionnaire. Il y en a des tonnes de vidéo sur le sujet

[@daviddunbar7702]

Why not remove the air filter and use an air box cover?

[@dirtbiketv1]

For sure the better way to to do it-- most guys will never get covers for their bikes and its for sure quicker and easier to not do it.

[@srt4driver181]

What lube are you using after the wash?

[@everpedregon8988]

What are y’all using to clean the wheels ?

[@AtticaEnduro_monohoma]

Love the mic!

[@viperracing2889]

Some put a plug in their exhaust and some special air intake cover. Do you recommend using these? To me it just seems risky to replace the air filter with a cover when the bike is dirty.

[@Natedoc808]

I use both after back in the day I got some water down my exhaust despite taping like he showed here over intake and exhaust- I put the bike up for the summer and the water rusted the head pipe to silencer joint. New exhaust setup was much more expensive than the butt plug and intake cover.

[@someonethatwatchesyoutube2953]

My 2020 KTM 300 is almost 1 year old and has about 70 hours on it. I removed the seat/tank and thoroughly washed it after every ride but I broke my rad shroud on the last ride so I put a new set on. The new plastics really showed how badly the original plastics (and the rest of the bike) are beaten up. So screw it. It’s just a pressure wash to clear the mud from now on and I’m happy not to care about its appearance any longer.

[@rtimetoride7645]

I ride in the sand all the time and no matter what I never get it all off. I think it's clean and I'll put the bike up and the next day I'll look at it and there's sand on the bike! I agree, F it

[@jmnh2009]

by laying the bike. it doesnt leak gas?

[@The2006200]

Not if it’s fuel injected. Or you turn the gas off.

[@marioschristofi3145]

Thanks for sharing your knowledge! What lube do you guys use?

[@ophx1337]

pointer finger mic goes crazy lol

[@panoskeits8365]

So, in short ,get one Spencer for your self.

[@dirtbiketv1]

haha-- He is a good help

[@FlorentinoLoco]

Every time my bike is laid over to its side it leaks either Coolant or gas.

[@bjarnefrederiksen7866]

The Honda’s front wheel looks like it is spinning really free. Anything special with it?

[@dirtbiketv1]

no - just wheel installed correctly

[@nickg5275]

So what do I do if I don’t have a power washer or compressed air

[@dirtbiketv1]

Get them-- -- for sure need compressor

[@nickg5275]

@@dirtbiketv1 damn guess I need to wait to clean my bike then

[@qtlawzy]

How often ane what would want you to change the oil

[@fortgreeneprojects1]

Nice bikes as well real nice bikes.

[@GeniusEnis]

Where does all of your dirt bike builds end up? Maybe everybody in the US know cus they see them at a marketplace or something. But I’m from Sweden and I’m kinda curious.

[@ninjaarcades7356]

Excellent

[@pjexc5500]

As allways excellent info love the video,s

[@eriknash8783]

I wish I had a patch of concrete to wash my bike on. I live up in the mountains and its all dirt so I wash my bike on the stand over the dirt and then have to move it into the garage to blow and hand dry the bike over a wood floor. It's pain and all my neighbors are water nazis since I live in California and on a community water supply. I also get home late in the dark so rarely am I doing all this immediately after a ride... I guess we should have had kids, lol!

[@jebediahnightlinger6357]

Just go poison their dogs, they'll be too busy dealing with that to worry about you.

[@Natedoc808]

Find a piece of scrap ply wood, or use a tie down to hold the bike leaning very far over.

[@jonnoMoto]

I wish my bike was that clean after riding

[@xlr8offroad]

MX....

[@AntiStressKit]

Thank you for the video

[@-PlayMaker-]

Is it bad if you get water in the airbox? I mean I know it's not ideal but will it hurt the motor if you start it with a wet filter?

[@Recedinghairline180]

Not unless it gets past the filter. Cover it with a plastic bag

[@henrikforsberg683]

There usually is a drainage on the bottom, remove the plug after washing and the water will drain out of the airbox. And the filter will also dry if you leave if for a while. But if you dont spray it to start with, you dont have to worry.. 😁 covering the holes or just avoid spraying close to them usually works good!

[@haydenbaha]

Can you please do a review of that Yamaha?? I saw it on motorcross action and curious how the 270 is especially with that air box cover.

[@hyposez1129]

I have a question. My bike is ktm sx250f 2020 so all the electronics and battery are under the seat so what should i do?

[@dirtbiketv1]

blow it off with air each time you wash-- Email me further questions -

[@hyposez1129]

@@dirtbiketv1 Thank you for your answer!

[@ericc90]

Nice garage 👌

[@td7124]

Thanks for this

[@premiumdetail5349]

Thanks sir

[@calebdavidson7115]

I have a 2010 CRF 250R Will the water not fry any of the wiring because it is fuel injected and it is more electronically done?

[@79series]

So it's okay to lay a bike down. Does fuel leak out

[@toddlemasters]

What hour meter is on the Honda? I just bought a new 250r and am looking for the best option

[@dirtbiketv1]

Works Connection. And a mount from them works well. Email me with further questions. Contact info in About tab.

[@toddlemasters]

@@dirtbiketv1 thank you so much. I certainly will with future questions! Love the content

[@boboleniczak1110]

Do you have thoughts on spraying out air box?

[@tbgtbg6311]

I like to rip the bike down the street a few times to clear out all water from engine and bearings etc.

[@justinelko588]

Do you spray anything on the engine afterwards, such as silicone lubricant or WD-40?

[@dirtbiketv1]

Email Jay directly with any questions. Contact info in About tab.

[@SLP-eb1wp]

Show us how you clean a completely mud caked bike. The kind of mud that wont even come off with a pressure washer.

[@NickW90]

Have you guys had any issues with the kill/map switch on the honda? Hear of people having issues getting them wet when washing

[@kennycouture2579]

Awesome video, love the channel. Is there a reason to start the bike right up after washing? I've been told to not start it right up due to water getting sucked into the air filter.

[@dirtbiketv1]

We tape off the vents get little to no water in-- I like to start it and make sure any water is run right out - right away-- .

[@dustin9035]

None of that worked for me. You better show me again on my bike.

[@rztrzt]

TIP: After washing spray the whole bike down with wd40 so it's covered in a thin film of oil. It prevents corrosion but the main thing is it prevents dirt from really sticking to the bike on your next ride and the dirt rinses off much easier afterwards. Another tip, instead of buying expensive cleaning products just mix some dishwashing liquid & clothes washing powder in a bucket of warm water, it works really well.

[@craighogland8509]

I've found a quick wipe with cheap "armor all" protectant does the same to keep dirt from sticking

[@hectichive889]

Nah man, that’s just too much. If you wanna good tip to avoid all this nonsense: Don’t wash your bike at all. It’s called a dirt bike for a reason, so let it earn it’s name! :)

[@danielcastelow7523]

I don't use compressed air I use a leaf blower win I blow my bike down

[@torr-michaelbennetta9785]

Never understand why people power wash their seats. You have to gently hand wash the top/wipe it down. Hose or PWing just saturates the seat foam, and males it crazy heavy and breaks it down. Can't believe you lay the bike right down on the ground with no stand , Jay.

[@chrispewkreme]

These bikes aren’t even dirty…. Dusty perhaps. We’ve got a nasty mud and clay that will stain everything red. No matter how hard you try, things will just turn red.

[@dylanhunt4162]

You forgot yo use WD40 on the brake disks.

[@charlottecolbert3707]

Starting your bike right after you wash it is the worst thing you can do your sucking water into straight in the airbox swap filters before starting it

[@spoderacing3910]

Don’t forget to wd-40 your brake rotors to help keep rust spots from forming. 👍

[@billymcfuggin7549]

I use waterproof grease on mine

[@straightnobraker4677]

blinker fluid also works well

[@LukeMorphett]

I love how thorough you are. However, I completely disagree about using a pressure washer. All that will do is push water into places it shouldn't be. Like behind the o'rings of your chain, into your linkage bearings, or any other bearing for that matter. I agree that pro level riders do it the way you've described, but, most of them don't have to buy their bikes, have mechanics maintaining them, get a new one every year (at least). And it's important for their bikes to "look the part." For us gumbies, a hose and bucket will do. Its a bloody dirt bike, they are supposed to look dirty.

[@classified0888]

Feels weird I’m spending money on stuff to clean my dirt bike to go gunk it back up in 2 days lol. But I guess you must wipe your asscheeks after taking a shit eh

[@audomaroruizdiaz3636]

Jjj

[@rileyross6230]

666 like

[@VanekLarson]

Getting famous off of comments day 267, so I can live the dream, live every day like it’s your last🤙🚀

[@bentleymtafu23]

This is so...organized. I am ashamed

[@elvispusley3515]

I feel like this is something that you know how to do from watching yer Dad. This how to video must be for all the Liberals.