Dismantling VX 18 engine coming from a Atomic Warhead 4x4 nitro buggy
Пікірлер: 34
@2112inuyasha12 жыл бұрын
I put this engine on my ofna ultra mbx comp. and it runs it pretty well. of course i did lightly modified it by taking the head shim out and putting a hpi .25 cooling head on it. also running 10% nitro, 18% oil.
@M3drivr8713 жыл бұрын
got it done thanks!
@amando9615 жыл бұрын
any ideas on removing the screws under the pull start, if they are really weak, and most likely get rounded?
@Alvyn2712 жыл бұрын
Thanks man
@Ybw200owns12 жыл бұрын
what is the part number for the lower engine mount screws?
@Buna9711 жыл бұрын
do you know the 4 screws that screw the heat sink to the engine? Well one of the holes that the screws scre into on top of the engine has its threads stripped. This means I loose a lot of ompression and smoke is coming out of the gap between the cooling head and heat sink. I am planning on getting a whole new engine. Or is there another way to fix this?
@YOYOMAN78613 жыл бұрын
which way does the hole in the piston goes
@DJHeroMasta11 жыл бұрын
There pull starters are way to big to fit onto my RS4 any advice or tips.
@xXZninjaXx14 жыл бұрын
what pecent fuel do you run for this engine i just got one
@amando9615 жыл бұрын
is ir hard to put it back together?
@TheOcm952 жыл бұрын
how did you get loose the part where the air filter sits?? working on a project with an old buggy and cant seem to remove the pin that holds it.
@piochu252 жыл бұрын
I can't remember to be honest it was that long ago. Is there any screwdriver fitting on it? Maybe it's just pushed in?
@Excel94310 жыл бұрын
Why, i run mine 30% and it been running strong for 2 years. Its been 6 gallons since
@FargothPL6 жыл бұрын
Hi. Do you remember dimensions of ball bearings? My engine has a leakage at the bearing and I want to order better bearings but I broke my caliper :/
@rc_teo_nade_2164 жыл бұрын
Get your bearing and go to skf
@carespa11 жыл бұрын
i have an o.s dtx18, i wanna know if the piston hole goes to the same side (facing carburator) if i change de side the hole will be to the exhaust side thanks
@eriff4 жыл бұрын
hello do you made this , will work, br!
@inoahmann75424 жыл бұрын
Maby you mentioned this in your video and I missed it but there what looks like an exhaust scavenging port that doesn't actually go anywhere. What is the purpose of this port?
@piochu254 жыл бұрын
Do you mean long flat port at 2:16?
@inoahmann75424 жыл бұрын
@@piochu25 no, it's a port on the sleve directly opposite the exhaust. It doesn't have a corresponding channel cut in the block. It is visible for a split second at 6:02:
@piochu254 жыл бұрын
@@inoahmann7542 it's a fuel intake to The cylinder, it works like on two stroke engine
@Buna9711 жыл бұрын
I could do that, but where do you live, I live in Yorshire in the U.K.
@piochu2514 жыл бұрын
16%
@piochu2513 жыл бұрын
@YOYOMAN786 hole facing carburator
@teonthevwwhisperer73163 жыл бұрын
Mine is going strong just screwed my cylinder head up literally I crossthreaded the glow plug
@piochu2515 жыл бұрын
drill the bolts heads off , and unscrew with pliers
@TwoAces013 жыл бұрын
Is it still a good engine?
@PauloIrineudeSouza2 жыл бұрын
Yes!
@Excel94311 жыл бұрын
Send me the engine i can use it for spare parts?!
@piochu2515 жыл бұрын
no, it's very easy :)
@Excel94311 жыл бұрын
Send it to ill pm you
@madhuvishahan85272 жыл бұрын
the video image is too poor, you need to fix it more
@geraradoification12 жыл бұрын
amigos, en este video no es la forma correcta de desarmar un motor, las llaves no son adecuadas, los tornillos tienen que ser en orden por el balance que produce la precion , el piston no se extrae de la manera que lo realiza. gracias por querer mostrarnos su tecnica pero no es asi. viva el rc