Display Case for Hot Toys BTTF2 DeLorean | Assembly & Review

iDisplayIt for 1/6 SCALE HOT TOYS DELOREAN TIME MACHINE MMS636 DISPLAY CASE CHAPTER INDEX:
Purchase the iDisplayIt here: www.idisplayit...
#delorean #hottoys #dmc12 #backtothefuture Disclaimer:
Due to factors beyond the control of DeLoreanTECH, we cannot guarantee against improper use or unauthorized modifications of this information. DeLoreanTECH assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. DeLoreanTECH recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of DeLoreanTECH, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not DeLoreanTECH.

[@solidtenpin]

My Mark 1 is in a custom sized case just like that (assembled with nuts and bolts by customer) from Sora Shop in Germany. It looks exactly like yours. You can just tell them what dimensions you want and they build it and ship it to you. Was about $120 back in 2016. I plan to do the same for my Mark 2. I put them in shelves and use the front, sides and top only (no back piece installed) so I can slide the case into the shelf over the car, it's the entire reason I went with Sora to begin with.

[@DeLoreanTECH]

Thanks for the tip. This is great info

[@Kal-el23]

Can the mark 1 case display it in hover mode with the doors closed if it’s low like yours?

[@DeLoreanTECH]

Yes it can!

[@tolust]

where did you get the " DeLorean " sticker for the base ?

[@DeLoreanTECH]

We make them!

[@dckoppen]

thank you for this review and information. I purchased a case for my mark 2. I also have the mark 1. One thing that is driving me nuts though, I can't power the Mark 2 with usb inside the case, because you have to push the button under the hood. The mark 1 doesn't have this problem. Such a shame 😔

[@DeLoreanTECH]

Agreed. They needed a latching switch not a momentary switch!

[@thedude2897]

I have several of these. None were bowed. Can't go wrong with them for the price.

[@martymcfly6886]

Very nice case! I want to buy one too but just a question, do you have to remove the top of the case everytime you want to switch on or switch off the lights? Because even when the usb is plugged you have to push the switch to activate the lights.

[@DeLoreanTECH]

What I do it just lift the case of the base a bit and then turn them on. You have to reach under the case. The clear case itself can be easily removed fro the base, it's just sitting on top of it with some alignment slots in place.

[@martymcfly6886]

@@DeLoreanTECH Oh ok but you always have to open the car hood right? Or you made an external on/off switch?

[@Alfie9000]

Would you say there is room to stand both Doc Brown and Marty in front of the Delorean with this case?

[@DeLoreanTECH]

yes, the case has enough "depth" to it

[@barryb36]

So how are you turning the lights on and off once the Delorean is in the case?

[@DeLoreanTECH]

Unfortunately I leave them off...since they have to be turned on using the mom switch

[@carildezeeuw454]

Promo-SM 💕

[@unrewritable]

Thanks for the video! Can I have the complete measurements for your case?

[@DeLoreanTECH]

Yes it’s in the video it is approximately 31” x 19” x 19”

[@かわさん-o9u]

こちらの台座はどこで手に入りますか？

[@Rob-z7k]

Wow..this is cool! I was thinking of getting this Hot Toys Delorean but the display part is the problem of having space. Also the display stand for the Mark 2 should have been poseable. I dont like the 1 angle it has

[@DeLoreanTECH]

Check out our display stand hack video!

[@thunderchild2237]

Hi My preferred case is only 33 and a quarter wide . Delorean is 35 wide wing mirror to wing mirror. If Delorean was on hover stand ...would there be enough space then to fit in because of said hover angle