Dixell control

[@jeremyvoshage2410]

So glad I learned from an old school mechanic like you 👍🤟

[@NorCal-refrigeration]

Thanks

[@BenTh17]

“It’s gonna bang on and take the load” 😂 Also I love your cat. Good video

[@Reefertech]

You make me want to get back into refrigeration! Fun stuff 🙌🏻

[@joinusmorelikely5428]

That’s so crazy I was just thinking about. How effing ridiculous the dixell robustibility is or lack of. I can’t tell you how many dixell stats had to be replaced because of water….. how rediculous is that???? A refrigeration stat that susceptible to damage because of water…. Unreal dixell needs to get there stuff together….

[@marvingarcia8982]

My man using True refrigeration compressor relay to help the dixell. I like the set up, am not sure if I would do it. That relay contacts sticks all the time. But the idea is undertood.

[@OcRefrig]

i use contactors all day long. especially on freezers. that way i can inspect the contacts and replace.

[@glasser2819]

@@OcRefrig or you can add a "soft starter" and never replace the contactor or the motor... 7x in-rush be gone 👍🏻

[@st3v3281]

What model relay is that Dave ? i would like to start installing also to take load off comp most units I service are always pulling high amps due to dirty cond coils or lack of air flow.. Great video

[@persimonsen8792]

Why not using Danfoss ? Like a EKC202D, perfekt for all rooms, freezer or cold rooms. Great control of defrost and fans. Even with battery module, you can control for special defrost time. And nightmode.

[@ronkurey8840]

Another fine job..Dave...do it right the first time...that’s what I like!

[@damianorsini4260]

Hobart is like, "oh no he didn't, that's our sticker." #STICKERWARS

[@OcRefrig]

Lol ! 🤣🤣🤣🤣🤣 Oh Yes he did ! 🤣🤣🤣🤣🤣

[@deanstanbank6200]

Do you ever use the Eliwell I.D. Chill n Freeze range over there. I use them quite a lot here in Blighty. I’ve found them to be a good, reliable controller.

[@heavydiesel]

They are good controllers, I keep a ID Cool and ID Chill n Freezer on the van.

[@deanstanbank6200]

heavydiesel Just subbed to your channel mate. After 12 years with the same company, I am finally giving it a go on my own. Looking forward to the new challenge.

[@NorCal-refrigeration]

Dean Stanbank I have not but I’ll look into those. Thanks for the heads up. 👍

[@throttlebottle5906]

either sticking contact or the temp sensors are getting spotty and telling it to keep running warm box? unless you/they seen the control reading 25F also

[@michaelmeyer6314]

Again, lets replace an electronic with a pressure switch, the only reason the electronic was dead is that the unit on the rooftop was designed for indoor use only.

[@glasser2819]

your external relay solution is the best to fix junko controls. Those external relays specs are perfect for handling in-rush surge currents.

[@NorCal-refrigeration]

They use them on true units.

[@glasser2819]

@@NorCal-refrigeration have you experimented "soft starting" motors: compressors, fans, pumps like on your private equipment. It saves the contactors and the bearings from destructive start surge currents and shaft translation (ATS01N125FT: "made in Germany" engineering for cheap. Both 1 and/or 3 phase motors) 👍🏻

[@chrisbivens5410]

Sick dog house. Crazy Those little shit controls handle the load. It is what it is.

[@OcRefrig]

That was a 2013 dixell. Lasted 6 years without a Relay taking the Load. i just replaced a dixell the other day. 2008 controller But , it Was using a Contactor to take the Load. 6 years Life No Relay or use a Relay and get 11 years Life out of controller. Goes to show you , You can double the Life of the Controller almost using a Relay. Good vid.

[@EdwardChuck-s3s]

If there is no display showing may I know what’s the problem

[@ceeceethecat]

Such a beautiful cat😻

[@NorCal-refrigeration]

Cee cee are you licking your beans again?

[@ceeceethecat]

@@NorCal-refrigeration What! How dare you Dave😹

[@NorCal-refrigeration]

CeeCee The Cat 😂😂😂

[@binhashimhvacrservices284]

The relay for load is the best thing to do.

[@michaelmeyer6314]

If you went to a wholesaler you could buy a Dixell Universal replacement and use it right out of the box. Do not replace with a Penn or Ranco.

[@leylyatl1049]

Could you help me please how to set up US LS Hy and other if controller dixell is installed on the storage boiler and I want to have permanent hot water around 50-55 °C ??

[@cesservicedepartment3609]

Good video, where are you getting your dixell controllers, united refrigeration charges a little to much.

[@mahesh1757sardesai]

What is EA ( letters blinking )error in dixell XR06CX controller, PLEASE reply at the earliest

[@frostcontrolhayder3463]

why the place of control is installed in the outdoor unit?usualy in the indoor.

[@NorCal-refrigeration]

It’s not a temp a controller, it’s the outdoor unit controller low pressure high pressure fan cycle time delay and more.

[@frostcontrolhayder3463]

@@NorCal-refrigeration we donot have frigs like this,its 🆒😂

[@scrambler350]

@ 9:38

[@ceeceethecat]

I didn't see any competition😹

[@stheodro]

can someone elaborate "Design pressures" on reach-in cooler data plate what it means? example on Traulsen G22013TS [R-404A] Design Pressure HIGH Side 350 PSIG LOW Side 250 PSIG is this talking about Max pressure the system can withstand? Thanks

[@NorCal-refrigeration]

Schematics yep. Designed for max.

[@stheodro]

@@NorCal-refrigeration Thank you Nor-Cal your channel has amazing content I love the tip you gave ( Dixell Control + Relay) would adding a fuse protect the controller any better? or would be a nuisance call?

[@gonzgarr1592]

Cal man did anybody you know Knows what ever happen to jim pettinato have not see any vidios from him for about 2 yrs just wondering if he is O.K

[@scrambler350]

One of the other guy's in the KZbin HVAC community claimed he stopped doing vids because he was getting too much attention from people locally and at his supply house or something like that - think he just went low-key.

[@gonzgarr1592]

@@scrambler350 thanks for the info

[@throttlebottle5906]

hiss hiss, scratch, meow... I'm not too good at cat language ;)

[@russell4309]

1:15 get that Hobart outahere!!

[@NorCal-refrigeration]

Sticker wars are fun 🤣🤣

[@michaelmeyer6314]

The relay is a cheap Omron 30 amp that will fail before the control will.

[@Eddy63]

1st comment Super Dave ... Do I win a Vangina full of liquor ... Lol ... Good vid ...

[@NorCal-refrigeration]

😂😂😂☕️🥓

[@TheTeto209]

One day can you do a video on how to read wiring ?

[@NorCal-refrigeration]

Gray furnace man has a series up right now. Go check out his channel he is the very best!!!

[@germane3955]

Read the schismatic there is you Answer

[@harrydickson4575]

👍👍👍👍

[@NorCal-refrigeration]

🤘🤘🤘🤘

[@MaikelJordao]

Okey okay okey okay 🤣👍🤣👍

[@seanintia77]

☝️

[@rocker8692]

People need to at least clean their coils,takes 5 minutes

[@jaybee1570]

Penn Johnson

[@throttlebottle5906]

dixell or dix-smell :))))

[@oumarkasse3251]

Alarme da

[@OcRefrig]

Good vid. where are u getting your dixells from ? ill bet kinda pricey ? u can text if u want.

[@NorCal-refrigeration]

Amazon

[@OcRefrig]

thanks.

[@Portergetmybag]

Why KZbin unsubscribed me from a non controversial channel like yours ill never understand

[@st3v3281]

What model relay is that Dave ? i would like to start installing also to take load off comp most units I service are always pulling high amps due to dirty cond coils or lack of air flow.. Great video

[@NorCal-refrigeration]

True 800182 Relay www.amazon.com/dp/B00EMJYRJ0/ref=cm_sw_r_cp_api_i_5M1FCbRPPJ4PF

[@mahesh1757sardesai]

what is EA error in dixell XR06CX controller, PLEASE reply at the earliest