DIY 15V to 200 000 V Cockroft Walton voltage multiplier

[@GaryMcKinnonUFO]

What are the functions of the control knobs on your plasma speaker control ?

[@ErCanEverything]

This is incredible👏👏👏

[@JeffreyMerilo]

Another amazing project!! Tha ks Mirko! Please provide more details to build the Cranial Stimulator 😅

[@JoshuaSHanson]

Ahh the HVTDCS, from X-Men Origins

[@nickroach6270]

You should not expect each stage to double the voltage. From Wikipedia: "The no-load output voltage is twice the peak input voltage multiplied by the number of stages N", not input voltage x 2^N

[@nickdavis3711]

I'm curious to know more about your flyback driver circuit. I like the control and adjustability over the Transformer output

[@GaryMcKinnonUFO]

Circuit diagram on his other cockroft-walon video producing 110kV.

[@anthonyrickardii6198]

Awesome and pretty impressive. Question, what would happen if you run both in the same polarities? And how I increase the spark length?

[@manfacestudios-yf4mr]

Nothing would happen

[@Laserpointergreen]

What happends if you use higher capacitance will there be less but louder arcs?

[@Edmorbus]

Do you share the circuit diagram on the driver?

[@radityawardana6800]

Excuse me Mr Mirko, can you share the buying link of diode 20 kV / 20 mA for your project about DIY 15 V to 200.000 V voltage multiplier?

[@taranchindarkar2579]

Whats the serial number , volts of capacitor and diodes

[@noahkleugh9323]

For safety, have you considered using bleeder resistors to drain the voltage off the capacitors?

[@MirkoPavleskiMK]

Yes, a 1M resistor should be placed in parallel with each capacitor

[@scienceinnovativebrain]

Which type of capacitor will use to get more current diode is taken 1 A 15kv current requirement is 0.6 a

[@MiguelDeMarchena]

About 4 years ago I made a stun gun with 3 dollars ark lighter kit and the same voltage multiplier model you using there, I wanted to use an old crt flyback but was not good because of the size and the power to operate

[@FrancklinPierre-v4b]

Hi Mirko, great video, how did you make the reverse polarity multiplier, please help me make one. Thanks in advance. keep up the great work.

[@MirkoPavleskiMK]

Schematic at: snipboard.io/Fsz3XH.jpg

[@yasirshahzad3732]

Where we can find schematic for this project?

[@DAVIDGREGORYKERR]

I could see that being used to charge a bank of capacitors so that you can fire a projectile down range i.e Railgun

[@Suavache]

Điện áp được nhân lên nhiều lần nhờ điốt và tụ xin cảm ơn đã chia sẻ với khán giả

[@nielsdaemen]

The sof music doesn't really fit the theme😂 But very nice!

[@ahmaddraws9144]

this is probably the best video out there to explain how to make a voltage multiplier, just one or two questions, how much is the lowest and highest voltage i can supply this with before it malfunctions/ explodes?

[@MirkoPavleskiMK]

I have not tried to load it to that extent, but of course it depends on the components used

[@Black-so4fs]

it posible make a jacob ladder with the multiplier?

[@florinpetrache7834]

I have an acrylic plate for the support of capacitors and diodes. Is acrylic good as a support?

[@MirkoPavleskiMK]

Yes

[@KClO3]

I have disposable camera circuit, I bypassed diode and removed the flash capacitor so I get 500v 25khz output, I get around 1cm sparks with around 3-4 stages, if I add any more stages it doesn't get any better the spark stays around the same.

[@ghostbombl8034]

One those 90s cheap ones?you just cut the cap put a jumper than cut the diod,with jumper thats it?

[@bass9112]

how much could i get by supplying it 42V (10+ A)?

[@DIYPhil]

Hi. What adjustment did you do on 5:03 to create a cloud of ionized air instead of the bright sparks? Thanks.

[@MirkoPavleskiMK]

I reduced the voltage, and plasma is also obtained by increasing the distance between the electrodes

[@DIYPhil]

@@MirkoPavleskiMK I made a 10-stage voltage multiplier and I noticed that the output voltage seems to decrease right after stage 5. what do you think is the problem why voltage not increase in subsequent stages? thanks for the wonderful videos.

[@MirkoPavleskiMK]

@@DIYPhil I think that in that case it is a matter of low power of the source of driving high voltage (HV transformer), actually the driver of the HF transformer. If the driver is self-made, try changing the number of turns on the primary of the HV transformer.

[@kL07_]

​@@DIYPhilWhat's the voltage rating of your capacitors?

[@DIYPhil]

​@@kL07_ if I remember correctly it is 10kV

[@wimlippens6231]

why the UF4007 diode,their is a diode inside the irf540

[@ganbatganbold674]

hallo. is the ionized air the same as ozone?

[@MirkoPavleskiMK]

Ionized air produce ozone

[@ganbatganbold674]

I want to build one of these for making wood color dark using ozone. can you help me ?

[@florinpetrache7834]

it is a problem if my diodes 20kv 20ma is made from two 10kv 20ma in series?

[@MirkoPavleskiMK]

No, it is not a problem

[@saikumarkumar7580]

I used hv source 1 circuit but when the input 12 v given from rectifier circuit the voltage get decrease to 3v ... Is then any alternative circuit ... And one more thing If the capacitor and diode ratings may reduce then the output will come or not..

[@MirkoPavleskiMK]

Most likely the 12V source does not have enough power

[@saikumarkumar7580]

Then sir how much volts should give

[@sherifhassan9258]

Excellent video Plz, can this curcuit operate motor 2 amp 100 volt ? Help

[@kruimels]

I have a question. Is the Output constant? I mean that it is not a pulse generator. I want to use high voltage for research ancient technology.

[@MirkoPavleskiMK]

Yes, it is constant output

[@kruimels]

@@MirkoPavleskiMK Thx for the answer!

[@johnnycash4034]

Do you share the circuit diagram on the driver? It is variable right?

[@MirkoPavleskiMK]

Circuit at : www.hackster.io/mircemk/diy-15v-to-200-000-v-cockroft-walton-voltage-multiplier-405e85 "HV Source - 1"

[@vanadiumV]

nice work greetings from Morocco

[@MirkoPavleskiMK]

Thanks

[@黄蟮]

@@MirkoPavleskiMK I finally found someone, teacher, can you teach me how to make an electric baton that can electrocute mice? The high-voltage generator I bought to make the discharge time is too short, less than 5 seconds, I want to make a 5000kv one that can kill mice at once

[@yourboi1842]

I commented on your other video, if the capacitors are rated for 20kv how can it output 200kv+. I made the same circuit as a child and learned the hard way that 3kv capacitors will blow themselves to smitheries at 20kv+ so how can the 20kv output 200kv?

[@MirkoPavleskiMK]

The output voltage is divided by the number of cascades and it is the minimum voltage declared for the capacitors

[@yourboi1842]

@@MirkoPavleskiMK any idea why why my 10 stage fried itself from 180v's caps were rated 3k and that was my assumption.

[@Jason-so6qt]

What voltage rating does the capacitors and diodes have?

[@MirkoPavleskiMK]

Diodes 20kV and capacitors 20-30 kV

[@trisuranto9922]

bisa untuk memasak air dalam panci berapa detik ...????

[@coding_vlsi_vietnam]

Amazing !!! Love your channel 🤝🤝🤝

[@MirkoPavleskiMK]

Thanks :)

[@jayantverma2959]

but flybacks have a rectifier in its does it still works with dc

[@MirkoPavleskiMK]

No, you must use AC HV trafo

[@Laserpointergreen]

Is it possible to do this without diodes

[@MirkoPavleskiMK]

No

[@Laserpointergreen]

Ok, i asked becuse i have a ton of capacitors but no diodes and i dont know where to buy them

[@florinpetrache7834]

Although it's like yours, with 10 capacitors it doesn't work very well. I guess it's because of the source which is fed from a 3.7v 9800mAh battery. Is that true or not? If I use an AC flyback with a ZVS module (the frequency in empty 60KHz and in load 120KHz) is it good? The diodes are fast but will be able to handle the high frequency of the ZVS? What do you say?I'm afraid of burning the diodes because of the high frequency.

[@MirkoPavleskiMK]

Unfortunately, I don't have experience with ZVS driver, so you have to try it yourself.

[@florinpetrache7834]

I found a transformer on the internet as a source for the multiplier. it has 8 or 9kv 20ma 50-60 Hz at the output. it is good as a source if dont work my ac flyback from tv?

[@MirkoPavleskiMK]

Yes it is good as source for the multiplayer

[@florinpetrache7834]

my input voltage is between 5-10kv. it wil work my multiplier with capacitors 20kv 1nf ,and with diodes 20kv 20ma?

[@MirkoPavleskiMK]

Yes

[@OmarOmar-zc6vm]

Schematics plz

[@shawncalderon4950]

Can you share the schematic?

[@MirkoPavleskiMK]

In the text below the video

[@shawncalderon4950]

Found it, thanks! Great video!

[@danielcarlosable]

Could you post the schema and the materials list please?

[@hobbyrob313]

I wonder, what's the use of it???

[@piotrlaskowski3124]

any it' s just get a very big voltage but the current is too week for any usefull electronic device

[@algharibe]

amazing

[@foruzeshpatrick2053]

Good time, dear friend, are you able to sell and send a similar sample? Thank you

[@GaryMcKinnonUFO]

Very nice.

[@kruimels]

I thought it was 1 cm for 10.000 volts.

[@GaryMcKinnonUFO]

@@kruimels Yes, there are 2 measurements. 30kV/cm for non-ionised air and 11kV/cm for normal atmospheric pressure, temperature and humidity. So for most purposes you are right. I think the 30kV measurement is an ideal situation description. I have modified my comment :)

[@milekokotov1964]

Одлично! Браво!

[@quantumenergysolutions9128]

Did you see the Amazing Fractal Capacitor? See Robert Murray Smith

[@BefekerSami]

WOW😮😮😮😮😮HIGH RAY OF VOLTAGE😮😮😮😮😮

[@حمیدجهانپور-ش3ع]

میشه استفاده کرد

[@shamy6346]

Waaaw ☠️⚡

[@imeprezime1285]

120 kV. Be satisfied

[@nickname5906]

multiplayer)) сразу понял гастарбайтер

[@jonaoconnor8065]

Brother

[@kiokayak]

Tuch that

[@melonplaygroundwoldoftank9399]

Emp