DIY 5' X 10' Outdoor Bar

First minute and 45 seconds are pictures of the project after that there's a video of the project 95% done, still have to sand and cover in marine grade polyurethane. Will soon attach the plans and materials used.
Material List: Bought most of it from Home Depot
12 - 2x4x8
16 - 2x4x10
33 - 1x6x10
4 - 4x4x8
1 - 2x6x12
2 - 2x10x10
1 - 2x10x12
6 Metal Roofing Panels
Teks #9 X 1 in. Steel External Hex Head Washer Sharp Point Roofing Screws
Maximum 1 gal. Cedar Natural Tone Semi-Transparent Exterior Stain and Sealant in One Low VOC
4 - Hinges
5 Lb box of Deckmate Screws

[@robyo1713]

Nice build can't wait for all the step by step. On what you did & the measurements.

[@noturavgdad]

Coming soon!

[@roberthennessey5912]

Plans??

[@amclymon]

Nice build looking forward to the plans and materials so I can tackle myself

[@noturavgdad]

Thank you, I’m sorry for the late response, I’m new to this KZbin thing, I will try to put them up this weekend.

[@roca5131]

Great job, I'll try to make one myself.

[@noturavgdad]

It really wasn’t that bad took me about three days and that’s because I couldn’t find some of the pressured treated wood.

[@noturavgdad]

Sorry for the long wait, I'm going to make another video this weekend during the day to show every section and their sizes. If there is anything you would like me to show or explain in the video let me know in the comments and i'll make sure to show and explain it .

[@Kac2rhyme2]

Even if you don't make a video would purchase the plans too

[@noturavgdad]

@@Kac2rhyme2 I didn’t use any plans, I’ve watched a few videos and just drew what I wanted and went for it. I am trying to make up some plans though just taking a lot longer than anticipated.

[@jettylbi]

Did you post the plans for this build? Great looking bar!

[@mehmeh5375]

Going to start on ours this weekend 🤞

[@noturavgdad]

If there’s anything I can help with shoot me a message.

[@robhopper5729]

This is great, it is just about what I am looking to build, but I want it around 10'x6' or so, I want to be able to fit my grill and blackstone inside. Do you have any design plans for this build that I could look at to modify for my design?

[@lukasvolosyn6890]

Awesome job on the bar. I have one question what stain or Varnish. Did u use . I really like that color it turned out fantastic.

[@noturavgdad]

Your friend has shared a link to a Home Depot product they think you would be interested in seeing. www.homedepot.com/p/Olympic-Maximum-1-gal-Cedar-Natural-Tone-Semi-Transparent-Exterior-Stain-and-Sealant-in-One-Low-VOC-79551A-01/305230163

[@lukasvolosyn6890]

Thank u very much for the quick response. I will using that on my project.

[@noturavgdad]

If there is anything you need help with feel free to post any questions and I’ll get back to you as soon as possible.

[@AdamPadilla-hl6ui]

Nice bar! Do you have plans I can purchase for this build?

[@noturavgdad]

No, sorry. I have been trying to make a sketch with all the sizes and materials used, but haven’t had the time. As soon as I do I will give it out for free.

[@sal6830]

Awesome job!! 🍺

[@edgarosnayo9135]

K va

[@kevlizbobo]

Great job!

[@noturavgdad]

Thank you 😊

[@ericwgregory]

Great Job, Can I possibly get measurements to make one myself?

[@noturavgdad]

The bar itself is 10’ wide 5’ deep

[@benjybronk7718]

Outstanding job... whats the ball park cost??

[@noturavgdad]

Entire project was around $1,500, that’s including screws, nails, etc.

[@B4c0nD4d]

Looks great. What is the height of the front and rear 4x4s? How much of a roof slope is there?

[@noturavgdad]

The rear 4X4’s are 82” the front are 87”.

[@B4c0nD4d]

@@noturavgdad Thank you! Starting my project next week. Did you use a framing nail gun for the 1x6s on the back and sides?

[@noturavgdad]

Yes, I used 2-Inch x 16 Gauge S316 Stainless Steel Straight Finish Nails. I nailed all the 1X6’s to the 2X4’s.

[@B4c0nD4d]

​@@noturavgdadThank you!

[@noturavgdad]

If there’s anything else you need help with you can always send me a message at [e-mail]

[@andresmarroquin1123]

looks great

[@noturavgdad]

Thank you 😊

[@rickclayton1680]

Could you put something like this on casters to move around if needed and help protect the base of it from getting wet?

[@noturavgdad]

I’m sure you can, but would have to be heavy duty ones and probably put a few on each side just to make sure it doesn’t sag.

[@AA1234575]

Currently building the same bar. What was the wood type and size you used for all of the walls? Great job.

[@noturavgdad]

I used 1X6X12 pressure treated wood for all four sides. The back wall was cut to 113” - the width of the bar was 10’ so I just subtracted the 3-1/2 inches for the width of each 4X4. So 120” - 7” = 113” each piece of 1X6, I used 14 pieces for the back alone and the pieces that were left over I used for the sides. I should have used 2x3 for the frame instead of 2x4 then I could have turned the the frame wood sideways instead of flat if that makes any sense. So technically the width of the 2x3 and the 1x6 would have been the same width of the 4x4’s. 0:28 also remember to use stainless steel nails or tested screws like deck screws as pressure treaded wood will eat up regular screws and nails. This is the majority of what I ordered from Home Depot: FastenMaster LedgerLOK 5 in. Structural Wood Screw (50 Pack) you really don’t need the 50 pack but that’s all I could find. WeatherShield 2 in. x 4 in. x 10 ft. #2 Prime Ground Contact Pressure-Treated Lumber (11) WeatherShield 1 in. x 6 in. x 12 ft. Appearance Grade Pressure Treated Ground Contact Southern Pine Lumber (25) Unbranded 2 in. x 10 in. x 12 ft. #2 Prime Pressure-Treated Ground Contact Southern Pine Lumber (1) Gibraltar Building Products 8 ft. Corrugated Galvanized Steel 31-Gauge Roof Panel (4) Unbranded 4 in. x 4 in. x 8 ft. #2 Pressure-Treated Timber (4) WeatherShield 2 in. x 4 in. x 8 ft. #2 Prime Ground Contact Pressure-Treated Lumber (20) Deckmate 3-1/2 in. Tan Exterior Self-Starting Star Flat-Head Wood Deck Screws #10 (5 lbs./280 pcs) Olympic Maximum 1 gal. Cedar Natural Tone Semi-Transparent Exterior Stain and Sealant in One Low VOC I’m going to try and make an updated video and go through all the sizes and how it was built. Hope this all helps.

[@AA1234575]

@@noturavgdad Outstanding description. I am making mine 8x5, so everything as far as the products you used are spot on to what I used. What did you use for you support header across the top of the bar, under your metal roof? Also, what did you use for the two end pieces of the roof that slant down, what size wood? Lastly, did you use Lag Screws to fasten everything into the 4x4? Thanks again!

[@noturavgdad]

@@AA1234575 ​ for the header in the front of the bar it’s just 2 - 2x4’s the bottom one is flat and the other on top of it flushed to the front of the bottom one, so from the sides it would look like an L. As for the slant of the roof, the two 4x4’s on the back wall were cut to the size of the actual wall itself 0:33 and the front 4x4’s were cut to a few inches bigger to give it the slant. The frame of the roof was then placed over the entire bar and screwed into the 4x4’s which gives it the slant. I will measure it for you later on tonight to give you the exact sizes. I can send you some photos if you want. Just let me know what you need and I will take pictures and videos of it for you.

[@AA1234575]

@@noturavgdad thanks so much for your info. I’ll shoot you another message if I have any questions.

[@AA1234575]

@@noturavgdad how did you round out the edges on the two outside pieces of the roof frame that attach to the 4x4’s, and what sized wood did you use for frame?

[@benjamindavis4130]

Do you think it can be made in a way that you can move around to other places?

[@noturavgdad]

I’m sure if it’s build it on a platform with some heavy duty casters it can be done.

[@denneyboy101]

I'm curious about what is the measurement of the pool

[@noturavgdad]

16’X32’

[@crystalblevins1196]

Did you use pressure treated wood then stain/varnish it?

[@noturavgdad]

Yes, when I built it, it was about 95 degrees the entire week so the pressure treated wood dried up quickly and I was able to stain/varnish it.

[@SpringfieldMa]

Any updates on plans😊

[@noturavgdad]

Sorry, I’m actually almost done with them. I drew them out but it looked horrible. I’m trying to do them on a program but it’s taking a little longer than I expected.

[@michaelspagnuolo9204]

How did you secure the 1x6 for the lower part of the bar? Brad nails?

[@noturavgdad]

Stainless steel Brad nails.

[@michaelspagnuolo9204]

@@noturavgdad you are the man. Thanks for the response… great job on the bar..🍻👍

[@noturavgdad]

Thank you I actually just checked my Amazon account, these were the ones I used. B&C Eagle B162SS-1M 2-Inch x 16 Gauge S316 Stainless Steel Straight Finish Nails (1,000 per pack) a.co/d/2h5VcAP

[@jdocmatt]

How did you attach the frame to the 4x4s?

[@noturavgdad]

Once the frame was completed I just flush mounted the frame 2x4 with the 4x4 and put three lag bolts for the 2 front 4x4’s and 5 lag bolts for the back 4x4’s. I screwed them in from the 2x4 side into the 4x4.

[@jdocmatt]

@@noturavgdad thank you!!!

[@josebriones5799]

If you could please send me the plans that would be great

[@noturavgdad]

I don’t have plans as this was built just watching videos and looking through pictures posted on the internet but I’m working on making them. I’m just trying to figure out what and how to make them so that everyone can follow them.

[@elpapaupa838]

That's nice but the rain can be thrown to the neighbors yard

[@od4407]

This is America who gives AF!

[@elpapaupa838]

@od4407 be my neighbor you find out now days people just go to sleep for ever

[@od4407]

@@elpapaupa838 Yea yea keyboard warrior, crying about water

[@elpapaupa838]

@@od4407 yea yea yea keyboard warrior crying 🖕🖕🖕

[@danielpalmer5138]

Where didbyou get the plans from

[@noturavgdad]

I didn’t have plans, I searched the internet for yard bars and then took ideas from a few and built this one. I’m going to do a video showing everything including the actual sizes and how it was all put together.

[@danielpalmer5138]

@@noturavgdad ok it looks amazing

[@noturavgdad]

@@danielpalmer5138 thank you 🙏🏻