DIY acrylic wind screen for Kawasaki Z900 or other naked streetfighter sport bike part 1

[@Nnonety26829]

amazing work ! about to make my own DIY wind screen my self , Thanks !

[@garyjohnson1970]

So happy to find this, had an incident, still rebuilding my Z1000 face, moved the turn signals up to my semi fairing. I still have the stock, but I want to create a lower to use with the head light and signals. It's all currently attached to the fairing frame, and looks a little too...naked!

[@jasearturo9181]

i dont mean to be so offtopic but does someone know a way to get back into an Instagram account..? I was stupid forgot the password. I appreciate any tricks you can give me!

[@gianniisaac2609]

@Jase Arturo Instablaster :)

[@jasearturo9181]

@Gianni Isaac thanks so much for your reply. I found the site thru google and im waiting for the hacking stuff now. Seems to take quite some time so I will get back to you later when my account password hopefully is recovered.

[@jasearturo9181]

@Gianni Isaac It did the trick and I now got access to my account again. I am so happy:D Thanks so much you really help me out !

[@gianniisaac2609]

@Jase Arturo Happy to help xD

[@StansE250]

Best selection that I’ve found for grommets is McMaster-Carr & Zoro

[@otszzz79]

Thanks for sharing. Helps me a lot with my own diy visor for my nmax. Ordered a facelift for my yamaha nmax , and visor comes only with complete set, and only clear ones in stock. So I want to duplicate the visor with either clear acryllic polyglass and and If succeed with that, I will dye it in tub with rit dye to give it a daroened look that matches my bike. Cos the black and black transparant sheets I cant find here in PH. Only Sintra board and up to 2 to 3 mm. I want atleast 4 to 5mm. I did find the nylon spacers online, will receive the facelift kit with visor this week, then I know how its curved. Ordered a heatgun , barclamps, jig blades . Still need to get some to sand and polish the edges fully transparant too. Saw one vid how they put the visor into the oven resting on 2 bars covered with alu foil, but I dont need to bend it that much. Hope it works out well, yours looks great. Very well done. This is the visor I am going to do kzbin.info/www/bejne/bmjRfZmKhs-DrKc

[@NalinKhurb]

Nice work, quite some effort

[@Profabdesigns]

Check Lowes Home improvement center, they are called rubber ‘nutsert’

[@eeunjeung]

put in on low temp oven or adjust with hotgun

[@shazykool]

good effort keep it up

[@RobertSmith-bh5cv]

What is the thickness of the acrylic?

[@vishnusr2211]

Hello how much is the thickness of glass here you used i also want to design

[@jasonjares1936]

about 6mm

[@m3talc0re]

I've never heard Bosch pronounced like that XD

[@azharhussain2270]

what is the thickness size of the acrylic glass? 3mm or 6mm

[@cablainmusic]

1/4 inch is 6.something mm. 6.25 ish if im remembering right.

[@firatsonmez]

Hello send you vector plan thx

[@pawelek2129]

next time try first oven on low temp

[@Majorvideonut2]

Too much of a point that could impale you in an accident.

[@berniediosana5917]

Daming kawento kesa sa gawa

[@Cr0zzAlpha]

@12:20 thank me later😬

[@user-en6sj8un9s]

Insta page @Motosthetics

[@did3d523]

on vois que dal bouze

[@shazykool]

put it on and show how it looks