after getting into a collision with my GSR with stock brakes, i needed to upgrade to something better for my brake setup. This video helped out a lot
@bighomieJ5X3 жыл бұрын
Wow , this brake setup is by far the easiest one ive seen 💯
@Zubawoo3 жыл бұрын
My man! you just saved my from drilling holes on My rsx! MVP right here
@FFAttack3 жыл бұрын
Glad you found this in time!! Hope you enjoy the amazing brake upgrade.
@brandon_buildsDIY2 жыл бұрын
@christian hernandez did you ever attempt this on the rsx?
@knix2for53 жыл бұрын
welcome to my new favorite channel !
@FFAttack3 жыл бұрын
Hey Thank you!!
@knix2for53 жыл бұрын
@@FFAttack thanks alot for content ! alot of stuff ppl say in forum you put to life in these vids and debunk some of the rumors ive heard for yrs
@FFAttack3 жыл бұрын
I’m trying! Really glad you like it and find value in it.
@knix2for53 жыл бұрын
@@FFAttack definitely do ! because these type of builds make great street car builds too. By just finding good oem parts that work great with little mods or no mods
@jaybud36463 жыл бұрын
I second that. Can't thank FFAttack enough for this video and his knowledge and tutorials.
@k24hybrid4 жыл бұрын
Very useful! Thanks for posting!
@TedSanno5 ай бұрын
Thank you for this info it will help with my time attack cb7 since it it is the same bolt spacing with the itr spindle. What is the recommended rotor diameter for this?. Is their a range that works.
@jwein1218 Жыл бұрын
Any word on installing Brembo calipers on the rears?
@uwkcal3 жыл бұрын
Great video bro! Keep up the good diy vids
@oscarkenji88393 жыл бұрын
this setup will fix into 16 inch wheels? good work!
@skotsephrenia13 жыл бұрын
Hello sir.. Kudos to you.. For this; I have a 1998 JDM itr 5x114 pcd with 36mm driveshaft.. Would this set up be suitable for my car without any further modifications? Thank you for help.. 👍
@FFAttack3 жыл бұрын
You will need to slightly machine the centre bore of the hub like I did in the video or the rotor to fit over it. It’s a very spall amount and any machine shop can do it.
@Whitehatch_ChecoАй бұрын
Seems like the brake pads are larger then the rotor and stick off of it
@blacksootgarage63692 жыл бұрын
Wonder if the rear would work
@k24hybrid4 жыл бұрын
wow!! you have very nice content!! What options did you consider before going to this setup? What do you think about Willwood's DPHA kit?
@FFAttack4 жыл бұрын
Well I had looked at FastBrakes Stoptech kit and the ASR AP kit. Both where very cost prohibitive for me being on a tight budget so where ruled out. I then looked at the Acura TL 4 pistons but a few people and things turned me off of them. From a size and bang for buck this setup I have put together is hard to beat. Sorry I do not know much about Wilwood kits. Thanks for the positive feedback on the content, I’m having fun making it and sharing.
@k24hybrid4 жыл бұрын
@@FFAttack awesome! 💪💪
@c2der10 күн бұрын
What size wheels are you running? Whats the minimum size required? Thanks,
@SinghSingh-ci5yc10 ай бұрын
Subbed and excited!
@Rayrosariodlc Жыл бұрын
Great details
@dickhertz76353 жыл бұрын
1/2 mm is irrelevant. Don't worry about a shim that small. Great DIY. Thanks
@FFAttack3 жыл бұрын
Thank you, I was not sure so error on the side of caution.
@davem8302 жыл бұрын
Thank you so very much for the detailed video! I have a couple of questions if you have the time. First is, which rear brakes are you using, are you using a bias adjuster and finally, what size wheel/offset/width are you using? Thanks again! You have a new subscriber in me!
@FFAttack2 жыл бұрын
I’m using stock GSR rear brakes with a Tilton prop valve. Wheels are 17x10 et18.
@davem8302 жыл бұрын
@@FFAttack that's good information. Thank you very much for replying!
@davidtcgroupr Жыл бұрын
What about a 4 lug rotor? What sizes fit only 12.6”?
@TheGabesable2 ай бұрын
Idk but I would look into mini Cooper rotors maybe a cooperS. I used to have a PDF with sizing and part numbers maybe you can find a similar document.
@jonrex38254 жыл бұрын
Hi great content btw ... would the oem genesis brembo pads work? Instead of the g loc pads or is there a difference between them. Thanks and also I'm still on the 4 bolt hub not type r on my dc2 any other rotor that you know might fit
@FFAttack4 жыл бұрын
Stock Genisis pads will work fine. This car is strictly for track so stock pads would not work. No options I know of for a rotor in 4x100. You would likely need to red till the 5 bolt rotors to 4x100. Glad you like the content!
@jonrex38254 жыл бұрын
@@FFAttack thanks for the reply ill look into it 16.8mm disc if I can find one ill let you know
@nhantran98 Жыл бұрын
any chance you can make a clearance profile off the brake with the anchoring point being the wheel hub?
@Jonysmoky_21086 ай бұрын
I need this ive been commenting this on all the videos i see 😅
@williamhallgren3604 Жыл бұрын
Does anyone know if those calipers would directly bolt on to a '07 crv?
@bonjouravecuns4 жыл бұрын
I don’t know if someone can confirm that my idea would work. Can I use rsx base 32mm bearing and hub in a type-r (crv) knuckle. ? Than I would only have to make a ring to make it hubcentric with the rotor. (64.1 to 68)
@Rattle_canned_restorations3 жыл бұрын
What? Just put the rsx hub in your stock knuckle. They all use the same bearing.
@drjimjam11122 жыл бұрын
Looks like the caliper is going to be on upside down? I believe the small piston is supposed to be at the oncoming rotor side with the brake bleed up.. This to prevent pad beveling as I recall.
@FFAttack2 жыл бұрын
Bleeder is up, no issues with pad wear so far.
@punkrockmaniac21 Жыл бұрын
In your honest opinion how well do these perform once they get hot? I also have a k swap ek civic with the Porsche calipers on my four lug set up but I want to go 5 lug to run 17inch wheels. Thinking about using the crv knuckle for the front. Trying to determine what front brake set up to go with, seen the TL set up, genesis set up, or maybe go with fast brakes on a custom set up but that’s easy 2k dollars.
@FFAttack Жыл бұрын
The track I use to drive on was known for being a brake killer, lots of slow corners with little straights so no time to really cool the brakes in a lap. These handled it just fine. Last year I removed the dust seals on the pistons as they like to catch fire. I just drop a drip of brake fluid on each piston to keep the seals fresh. I have run these for a 45min session in 32c weather and not had brake fade. I do have corvette brake ducts (have a DIY on them). So I have a steady flow of cool air. Pads are really important too, the G-Loc R16’s take all I can toss at them. Now that I run on less brake abusing track I’m not worried about this setup handling heat at all.
@rodolfoguardado43834 жыл бұрын
What size wheels you used to clear the caliper
@FFAttack4 жыл бұрын
I’m running 17x10’s et18 on my car. Fitment will really come down to the specific wheels. 17x9 RPF1’s do not fit but 17x9 Konig Hypergrams do. That’s all I have tested.
@jamesnorth77764 жыл бұрын
Where can I find these calipers? eBay hasn't shown me anything less than $1700 USD from spain
@FFAttack4 жыл бұрын
I guess they have become popular for some reason 😉. Look on Rock Auto, a few I know have got them from there.
@rodolfoguardado43834 жыл бұрын
Hey the setup will work for 1999 crv
@FFAttack4 жыл бұрын
Yes it will, this car has CRV hubs and spindles, just needs wheels to clear them.
@Dc2_kevoo2 жыл бұрын
Hey great video had no idea this set up was a thing so the machine shop made the bore smaller or added to it to fit the rotor ?
@FFAttack2 жыл бұрын
They had to machine a small amount off the cantering ring of the hub. I also could have had that taken off the rotor instead but wanted to make it so I could get a replacement rotor anywhere and just swap it on if I had a failure on track.
@jamie_ej112 күн бұрын
How different are the tl-s calipers? I ask bc I have a set
@MrVtecnology13 жыл бұрын
Hi. I read all the comments and In what your videon3 times. I know you said the rotors come from a Nissan rouge with 3d row seat. Now. No one asks here, the year of the Nissan and model. Wen, you try to get the rotors, those are the info you need to get the right ones. Did you still have that info? I will be the rotors part number? Thanks. I'm looking forward to upgrading my Crv 4wd turbo brakes.
@FFAttack3 жыл бұрын
Thanks for that I updated the show notes with the year I used. It was a 2017 MY
@xavierolle Жыл бұрын
If ain't wrong you could use ep3 ctr or rsx-s hubs wich have 64mm center 🤔🤔
@FFAttack Жыл бұрын
That’s correct, when you have the larger Wheel bearing CRV/ITR spindles you can direct swap the hubs. I’m in the process of doing that now so I can run the slightly larger (07-12) Sentra SE-R specV rotors.
@michaelmcfarland23532 жыл бұрын
Would these brembo calipers work well with the base model mini cooper rotors that a lot of people commonly use as a big break upgrade for civic/integras? I believe those rotors are 280mm which is ~11" and are 4x100
@FFAttack2 жыл бұрын
No they won’t, the Callipers is made for a much larger sweep. Stock the Genesis runs 13” rotors so putting a 11” rotor in them will not work. This setup I did runs a 12.5” rotor if I remember correctly. In the video I compare them to my TypeR rotors that are the same size as the mini ones.
@ariesr48832 жыл бұрын
Figment for DC5?
@FFAttack2 жыл бұрын
Not sure, I know others have made it work on a 8th gen civic.
@rufinocolon56374 жыл бұрын
What rotor can I use if staying 4 hole rotors? It would be for a Integra LS coupe.
@FFAttack4 жыл бұрын
You can use the Rogue rotors as outlined in this, you just need to get them red re-drilled to 4x100.
@cristianpozos13883 жыл бұрын
If I’m going from a 4 lug to 5 lug in the front what rear hubs can I uses to match the 5 lung that would fit my 92 eg? Or is there a wheel I can buy that would fit both stud patterns?
@FFAttack3 жыл бұрын
I still have 4x100 rear, my car runs 17x10 front and 17x8 rear so I’ll never be rotating the wheels and tires front to rear anyways. Generally to do 5x114.3 rear you need ITR stuff.
@elmilamores76867 ай бұрын
@FFAttack you can always go CR-V front knuckles and prelude SH rear hubs on stock eg/da/dc trailing arms.
@donnguyen60563 жыл бұрын
Plz tell me where you get the brake line ? Thanks
@FFAttack3 жыл бұрын
It’s just a beaded steel like kit for a EM1 Civic.
@TheCordrick4 жыл бұрын
This is all five lug stuff. What about four lug bro?
@FFAttack4 жыл бұрын
Honed developments makes a cost effective bracket to adapt Porsche Calipers to a 4x100 Honda. I recommended check them out.
@TheCordrick4 жыл бұрын
Damn bro thank you for replying...
@josephnguyen28184 жыл бұрын
Will the brembo rears for a genesis work for the integra?
@FFAttack4 жыл бұрын
In the rear of an Integra? If so I have no idea. The rear brakes are more than enough stock.
@oldsklteg4 жыл бұрын
Subscribed 👌
@RaphaelYC4 жыл бұрын
I have a TSX and thinking to purchase these Genesis Brembos too. However, I am wondering if you would know the pistons sizes of the brembos, since we have to swap them left to right if the brembos have different size calipers it will mess up the balance right?
@FFAttack4 жыл бұрын
The pistons on the Genesis Brembo’s are all the same size. They do not have a leading and trailing piston size on each so swapping sides has no ill effect.
@RaphaelYC4 жыл бұрын
@@FFAttack For brake pads, are the just same with the STI or EVO pads?
@FFAttack4 жыл бұрын
RaphaelYC they are GP1001 pads the same as STI/ EVO as far as I can tell.
@RaphaelYC4 жыл бұрын
@@FFAttack Hey just received my rotors, pads and calipers. The pads seems to be bigger than the rotors surface will that be a problem?
@ecutc32 жыл бұрын
If I have the 4 lug on my integra usdm (dc4) will this work? How can I do it with 4 lug?
@FFAttack2 жыл бұрын
You could probably see if a machine shop will re drill the rotors. Other than that I’m not sure.
@ecutc32 жыл бұрын
@@FFAttack ah ok. Thanks !!
@wickedsatan13 жыл бұрын
Genesis brembo calipers used cost over $500 these days :(
@FFAttack3 жыл бұрын
Yep the popularity has gone up recently. I believe you can get remain on Rock Auto for about that now.
@justintowers82308 ай бұрын
what is the spindle spacing on the ITR?
@jeremiahmcknight9495 Жыл бұрын
I have a d series track built ek. Considering this upgrade. Will the stock axles mate with the crv spindle ?
@gr8bart1 Жыл бұрын
I think you'd need CRV knuckle, CRV bearing. RSX base model Hub wich is 32mm axle. The Type S RSX hub is 36mm
@FieldGenEJ2 жыл бұрын
Any issues with noise from the brake swap? I've been reading on a forum and there were several complaints about a squealing noise.
@FFAttack2 жыл бұрын
My car is a track only car so yes I have some brake noise using race pads. Not sure about on road, I know a few with them on dual purpose cars with out complaints.
@TheMgiorivera Жыл бұрын
8th and 9th gen fit on also ?
@sirdragos1336 Жыл бұрын
Hi! Does anyone know what's the width of the rotor?
@tjimjong17682 жыл бұрын
Hi would the Hyundai Santa Fe Dm Brembo calipers work as well for this set up? Thanks
@FFAttack2 жыл бұрын
No idea, never seen them or tried.
@gapgodmario2854 жыл бұрын
Can i just use a type s rotor?
@FFAttack4 жыл бұрын
I did not try them and believe they are smaller but 20mm.
@King_Rematch7 ай бұрын
anyone know if this will work with a 22 civic si?
@jeremiahgarcia88612 жыл бұрын
I have a db7 integra do you know which calipers I can use for my car I'm having trouble finding them
@FFAttack2 жыл бұрын
I’m sorry I’m not sure about the db7.
@jonnywu50583 жыл бұрын
How is the brake pedal feel after installation? Did you upgrade the brake master cylinder?
@FFAttack3 жыл бұрын
It’s fantastic, firm and much easier to modulate. Breaking distance was much improved as well. I’m still running a stock 1” master.
@jonnywu50583 жыл бұрын
@@FFAttack Nice! What about the brake bias? Did you adjust anything?
@FFAttack3 жыл бұрын
Yes I did redo all the break lines in the car and installed a Tilton prop valve. I have heard about others running on a 40/40 valve with a very low bite rear pad.
@jonnywu50583 жыл бұрын
@@FFAttack Good to know. Just curious. Why did you redo all the brake lines? And decreasing the brake line pressure for rear brakes would give better brake response?
@FFAttack3 жыл бұрын
I redid them to allow the Prop valve and simplify. I wanted to be able to adjust bias easily. Up here we get a lot of wet or damp track days so being able to adjust braking is a good idea. On these Honda’s the factory lines are Married front to back meaning the drivers front is on the same circuit as the passenger side rear and same on the other side. So when you put adjustable prop valve in you kind of need to do the lines. Ideally yes you do need to reduce pressure to the rear when going this big in the front. Going with a low grip rear pad is a bandaid but can work as well.
@meganmather47962 жыл бұрын
Got a question I have 2011 Hyundai Genesis R Spec Calipers are they all the same and what diameter where the rotors
@FFAttack2 жыл бұрын
I believe all the R Spec calipers are the same. The rotors I used are 12.5”z
@oscarreis96043 жыл бұрын
Its work with 16’ wheels?
@FFAttack3 жыл бұрын
It really depends on the wheel, I have not tested this with any 16” wheels.
@mihailpetrovici50442 жыл бұрын
God daaamn🤤
@travisgallegos9363 Жыл бұрын
What hubs are you using? 36mm itr? Or USD 32mm itr
@FFAttack Жыл бұрын
36mm CRV/ITR hubs.
@fra8449 Жыл бұрын
For brake line you use itr aftermarket line or custom?
@FFAttack Жыл бұрын
ITR but the callipers will accept any Honda banjo line connection.
@rodolfoguardado43833 жыл бұрын
Can I use tl rotors and brakes with those calipers
@FFAttack3 жыл бұрын
No idea.
@wickedsatan1 Жыл бұрын
Can these calipers work with 4 lug nut hub & rotor?
@djsonicc Жыл бұрын
Calipers would but you won't find a rotor of this size in 4 lug
@calebbruce43462 жыл бұрын
What master cylinder/Brake booster setup are you running?
@FFAttack2 жыл бұрын
I have a 1” Integra master and the factory Civic booster.
@davidtcgroupr Жыл бұрын
What about the rears does genesis rear fit in the rear
@FFAttack Жыл бұрын
Can’t help you with that sorry.
@chriscas-ToolAficionado4 жыл бұрын
Tell us about this titanium plate please. What are the claims?
@FFAttack4 жыл бұрын
I’ll cover off the claims and what they are once I have them in hand. I’ll probably have them in a future episode.
@Jaydogg209 Жыл бұрын
@FFAttack did you make a video yet? Please attach link if so.
@itsjustWebbie2 жыл бұрын
Ok all the searches I've keep coming back with the CRV hub diameter of 64.1. What hub do you have at 70.1? I'm so confused. Because if the CRV is 64.1 and the Rouge rotor is 68 then you shouldn't have to machine. I'm only asking because I don't have too many machine shops in my area willing to do this.
@FFAttack2 жыл бұрын
The wheel Center boar maybe that but the part of the hub the rotor centres on needs to be same as the rotor.
@xavierolle Жыл бұрын
If ain't wrong the crv hubs are 71.X like the jdm itr hub, the thing i think it works is to put the ep3 CTR or the rsx-s (i think are the same) hubs wich fit in that spindle because they have 36mm shaft but the center is also 64.X like regular 6gen civics integras etc, someone correct me if im wrong but recent information i read goes in that direction
@FFAttack Жыл бұрын
That’s correct, I’m putting RSX Type S hubs into my CRV/ITR big bearing spindles. This should get around any need to machine anything then use Sentra SER Spec V rotors.
@henrybui63534 ай бұрын
@@FFAttack have you tried the sentra se-r spec v rotors with the rsx type s hub yet? Looking at specs, the rsx hub is 64mm and the sentra is 68mm still. So the rotor wont be hub centric. Are these rotors hub or lug centric?
@FFAttack4 ай бұрын
@henrybui6353 not yet, the way the Rouge ones are setup on my car they are hub centric.
@rodolfoguardado43833 жыл бұрын
What other brake pad could work with the set up
@FFAttack3 жыл бұрын
Any pad for a track pack Hyundai Genisis, Subaru STI or EVO.
@integraonabudget9584 жыл бұрын
Can I still keep 4x100
@FFAttack4 жыл бұрын
If you re-drill the rotor to 4x100
@integraonabudget9584 жыл бұрын
FFAttack the Nissan Rogue 3 row rotor right
@FFAttack4 жыл бұрын
Yep
@integraonabudget9584 жыл бұрын
FFAttack what’s the smallest wheel I can run with that set up
@mihailpetrovici50442 жыл бұрын
That's the biggest I've seen on a civic
@dineshe37194 жыл бұрын
I can find genesis calipers locally but on left side is available? Can I buy two left side calipers?
@thomaspotemciano4 жыл бұрын
No, you need both calipers. If you put two left caliper installed then only the left on will work properly. Installing a left caliper on the right side will place the brake bleeder valve upside down. The brake bleeder valve must be on top or else the brakes will not bleed the air out properly.
@oldsklteg4 жыл бұрын
@@thomaspotemciano bleed the calipers off the car similar to what we do with rsx rear calipers on DC integra.
@integraonabudget9584 жыл бұрын
Am I going remove the abs or will it still work
@FFAttack4 жыл бұрын
I’m not sure, my car came without ABS. Generally a brake change like this will not effect ABS. The CRV hubs used have the ABS tone rings on them.
@karenmadden89503 жыл бұрын
Will these calipers fit the 9th gen civic?
@FFAttack3 жыл бұрын
I hear they do but I have never done so myself.
@carlosmateus13064 жыл бұрын
hello this calipers fit in a honda civic type R ep3? thx
@FFAttack4 жыл бұрын
Sorry I do not know, I think it will with the same rotor I used but have not tried it.
@Luckyblooms7 ай бұрын
How is the pad coverage w the Rogue 12.6” rotors? Trying to determine if the 12.44” rotors from the 09-12 mini JCW would work for 4 lug folks. Do the rogue rotors have the same offset from the hub mounting face?
@FFAttack7 ай бұрын
With out trying it I could not tell you for sure. I believe you would have a lot of pad overhang if you ran it on a 12.44 rotor.
@Luckyblooms5 ай бұрын
@@FFAttack measurement wise it should be around 2mm overhang depending on the pad. Not optimized but should be functional in theory? Based on technical drawings I can find, the caliper should work with a pad shim on each side to take up some thickness. Might order a rotor from Rogue and Mini to compare 1:1
@FFAttack5 ай бұрын
Yes your right, sorry I was thinking the smaller Mini rotor, that would not be bad. On my setup currently I have 1-2mm of pad overhang. Since I inoculate did this I have heard the Sentra SE-R rotors are fit with no pad overhang. I plan to try it when I need to change rotors. Nothing I have seen for 4x100 though.
@Luckyblooms5 ай бұрын
@@FFAttack which year of Sentra? If I’m ordering to take some measurements, I can try to have a peek
@FFAttack5 ай бұрын
@Luckyblooms I have not dug into it enough yet to know for sure. I was told you also need to run the RSX type S hub with the larger hub centric ring. I believe the 2007 Serra SER Spec-V is the one that is needed. CENTRIC 12142098 Rotor from my quick search.
@ricsona31942 жыл бұрын
Would this work on a 9th gen civic si?
@FFAttack2 жыл бұрын
No idea, I don’t have one.
@oodles86 Жыл бұрын
What do you use for your rears?
@FFAttack Жыл бұрын
Just Integra GSR disk breaks.
@diegocarmona12622 жыл бұрын
Can the 15 inch CTR wheel be used with this big break kit ?
@FFAttack2 жыл бұрын
I doubt it, they won’t fit under a lot of 16/17” wheels.
@diegocarmona12622 жыл бұрын
@@FFAttack thanks its not worth it then im not putting 17s on my EM1
@Whitehatch_Checo Жыл бұрын
Will it work with itr 32 hubs ?
@FFAttack Жыл бұрын
If they are 5 lug I would think so. I did not try it though.
@zackt20964 жыл бұрын
Have you tried fitting 16inch wheels with this big brake kit?
@FFAttack4 жыл бұрын
Zack T you need a minimum inner wheel barrel diameter of 385mm if you have that then you will need to make sure the spokes of the wheel clear. I have no 16’s to check fitment with.
@FFAttack4 жыл бұрын
Currently I don’t have wheels, this Covid19 shut down has slowed the wheel purchase. I have spoken with Konig and plan to run the 17x10 Hypergram wheels over these. I had them check and a 17x9 will also clear.
@FFAttack4 жыл бұрын
Yeah it’s tough to say, do you want me to take some measurements off my hub so you can see if they are close?
@thomaspotemciano4 жыл бұрын
These brembo calipers are very similar to ones subaru uses. With subarus with STI Brembo swap generally anything 16" dont fit. But Ive heard people running 16x8 or larger with some machining work done to make them clear 4pot calipers. But generally the rule is 17x7 or larger on for brembo 4 pots calipers
@royceyokono4 жыл бұрын
Do you think 16” wheels would fit over this setup?
@FFAttack4 жыл бұрын
Possibly but would be wheel specific, it will be very close if they fit at all. I’m on 17” and needed to be carful what wheel I got to go over the brakes. RPF1 17x9.5 will not clear due to a lip in the barrel.
@feelthatfeelthat3 жыл бұрын
Why would you even want to fit 16's? 17's are faster cheaper and much much much better tires available.
@FFAttack3 жыл бұрын
Totally agree, 16’s did not even weigh into my plans. If you need bigger than 15” it should be straight to 17”.
@pinoyyue283 жыл бұрын
Wat abt 4 lug integra? Wat rotors do I wed plz?
@pinoyyue283 жыл бұрын
Need*
@FFAttack3 жыл бұрын
You will need to re drill the same rotors I used.
@Esdru2216 ай бұрын
"budget" 700$ calipers second hand
@FFAttack6 ай бұрын
At the time this video was made they were all over EBay for $150 each. I did this complete setup for $500. Compared to anything else this size that’s budget.
@luvyourmomspie7 күн бұрын
@@FFAttack I just paid$600 complete with new pads n new rotors
@TheRealBootyWarrior3 жыл бұрын
Exciting
@actontreadway1168 Жыл бұрын
helpful, tks
@Oldieeeee4 жыл бұрын
With these fit a 2010 Honda Accord?
@FFAttack4 жыл бұрын
No idea
@Oldieeeee4 жыл бұрын
@@FFAttack well it was worth a shot lol
@FFAttack4 жыл бұрын
It would not cost much to get a rotor and a caliper to test. That’s how I figured this out.
@baagomez65953 жыл бұрын
It’s work for my Honda Accord 2005 , this caliper work with all Honda 👍🏼
@gregautomotivation3 жыл бұрын
@@baagomez6595 did the rotors work ok ? I have the same car
@Kevin_Vue_Racing3 жыл бұрын
what year CRV are those hubs from?
@FFAttack3 жыл бұрын
This is out of a 2000. As far as I know all the 1st gen USDM CRV hubs are the same.
@uwkcal3 жыл бұрын
@@FFAttack is it safe to say crv hubs and integra/civic hubs are the same bolt patterns size for the calipers besides crv being 5lug? Also how does this compare to the tl Type s brake calipers rotor sizing? I heard u can use type s tl calipers aswell brembos
@FFAttack3 жыл бұрын
Yes I believe they are. The CRV does have a larger wheel bearing as well. I did not look to closely as the TL type S stuff as I do not believe it was direct bolt on. Plus I think the Genesis Brembos accepts the larger rotor but don’t quote me on that.
@Blackhemicameron3 жыл бұрын
Anyone know if these calipers bolt up to the 90'-93' Integra spindles?
@luisbustamante19383 жыл бұрын
What year of the Crv to get the spindles??
@FFAttack3 жыл бұрын
Any 5 lug 1st generation CRV.
@javi_nikkiecuevas44303 жыл бұрын
@@FFAttack lower ball joint Can I use Buddy club extended lower ball joint or has to Crv lower ball joint?
@FFAttack3 жыл бұрын
Balljoints are all the same.
@waldotorres64133 жыл бұрын
What 4x100 rotor can I use for that brake caliper
@FFAttack3 жыл бұрын
Not sure there is a direct cross over. I went 5 x 114.3 to get this to work.
@CjeiC4 жыл бұрын
would these work on a 9th gen civic si?
@FFAttack4 жыл бұрын
I’m not sure.
@haidarpng2 жыл бұрын
What submodel nissan rogue? Man i cant find the rotors at all wtf
@FFAttack2 жыл бұрын
2017 Rogue 2.5L w/3rd row seats. Search on Rock Auto for RAYBESTOS 981779R Rotor that will get you into the right area.
@haidarpng2 жыл бұрын
@@FFAttack thank you so muchh!!! I found them on rock auto like u said...i picked up some refurbished rebuilt brembos from oreilys.. and now im worried will the rogue rotors fit my accord? I have a 2019 accord 2.0 sport... 64mm hub size.. 5x114 bolt diameter... the nissan rogue rotor is 68mm.. is that still okay? Will they still fit
@FFAttack2 жыл бұрын
No idea, only tried them on my 6th gen Civic.
@davidvillalobos44864 жыл бұрын
Can you run these calipers on a factory 4x100 hub?
@FFAttack4 жыл бұрын
Yes you can, you would need to get the rotor drilled to 4x100 and find a 17” wheel that they fit inside.
@abdullahr.a99424 жыл бұрын
Can i run these calipers on 4*100 lugs rotor or its must to have the roque rotors ?
@abdullahr.a99424 жыл бұрын
I did the the brake conversion on my ek with integra 4 lugs brake w/calipers , does it fit or need some mods?
@FFAttack4 жыл бұрын
@@abdullahr.a9942 need to get these rotors and re-drill to 4x100.
@abdullahr.a99424 жыл бұрын
@@FFAttack thanks , good luck
@jordy11729 ай бұрын
Hey would this brake kit fit a Honda civic 1998 LX model?
@FFAttack8 ай бұрын
Depends on hubs and wheel size.
@josephgaeta78363 жыл бұрын
what do you do for the rear on a regular integra
@FFAttack3 жыл бұрын
The rear Integra disc brakes are ample for most cars. I have had no issues with mine and this setup.
@marcosvega3464 Жыл бұрын
will these calipers work on an 8thgen si?
@Oofsmageroo Жыл бұрын
yup. unfortunately they cost much more than the TL-S calipers. from what I can find anyways.
@FFAttack Жыл бұрын
When I got them they where far far cheaper. I guess demand has gone up.
@bhinosrt85573 жыл бұрын
Will the genesis brembos work for my 2020 Honda Civic sport?
@jaybud36463 жыл бұрын
I believe they will. Only thing different than here on this video is 2020 Sports have 64.1mm hub centers, so you shouldn't need to machine your hubs down to allow the rotor to fit.
@bhinosrt85573 жыл бұрын
@@jaybud3646 thank you so much bro I already tried it the TL type S rotors fit well with the calipers. I just need bigger wheels to clear
@jaybud36463 жыл бұрын
@@bhinosrt8557 I found used Genesis calipers today by some miracle. Bought em and are being shipped out. Here tomorrow hopefully. I have a 19 hatch sport. Nissan Rouge 3rd row rotors ordered as well. Going same route as in the video.
@bhinosrt85573 жыл бұрын
@@jaybud3646 if the new pads don’t clear just sand them down even to make the rotors spin free
@jaybud36463 жыл бұрын
@@bhinosrt8557 for sure. Refaced many a pad before. Large knife stone, files/rasps, even used a cinder block once. Firm believer in I'll figure out a way no matter what. I don't give up. Stubborn as a mule, I believe it's called.
@rickyzlab99104 жыл бұрын
Would this work on rsx? Spindles?
@alland123455 ай бұрын
Would love to know as well, thanks. @FFAttack
@FFAttack5 ай бұрын
I believe if you have a RSX type S and run the Sentra SER Spec-V rotor you can. I have not confirmed this though.