DIY Dust Remover How to make a Compressed Air Can

[@jimraymond67]

Absolutely the best of the 5 videos I've watch. No epoxy and no soldering. Great job.

[@fixitsamo]

+Jim Raymond Thank you

[@joshchelvolski1033]

This tubeless tire valve actually works. When i tired to fill it with air using a 10z can, what my tire inflatior did was compress the can with air up 120 psi only once now it will only compress it with 40 psi. I am guessing what you need is an actual air compressor and not a tire inflatior. With the tire inflator i would only get about 4.5 seconds of air because i would have to unscrew the tire inflator from the tube less tire valve in which in doing so release some of the air from the can. My best bet would be to refill at a gas station inflator or get my own air compressor since i needed one anyway.

[@tripjet999]

I tried this, the can exploded when being filled and I tell all this to you from the great beyond.

[@ownerfate]

I may add gauge... thanks for that. i shall pay my respects F

[@lytnin88]

May you rest in peace.

[@dewitubeX1]

Lmao 🤣 wow how you reach youtube messages? Through god-fi?

[@Dansk55]

Rip

[@dfwfishfeen8909]

Now there's a message from above 🤣

[@HectorDomino.]

I didn't even have a clue that this can be done! Awesome work buddy. You are truly amazing.

[@fixitsamo]

+Hector Domino thank you

[@cjaimage1302]

Thank you I would have never thought of doing this! Unfortunately I threw away all my air cans and I need one ASAP. I’ll definitely do this to the next air can I get my hands on. I’ll give full credit to you if I ever use it in a video or demonstration. Thanks for that.

[@greatnew_products7436]

Nice, but the part you don't show is that you have to shake and discard all the DEBRIS generated by the drills and the sandpaper. This might be kind of obvious for some people, and that's why you didn't show it, but judging from the comments, some of your viewers have no idea... The debris could clog the spray nozzle or eject a small piece of metal at a very high speed towards a delicate piece of electronic. Thank you.

[@nasirmk]

how many PSI do you pressurize it to?

[@johannklein7284]

Hi Sir. How will I know if the air refill is already full on the can? What would you feel with it?

[@MixYourWay]

Well this is quite interesting! You know I'm a sound mixer for independent films/documentaries, and we usually find ourselves recording in very harsh and remote locations where dust and particles end up causing malfunction and damage to our equipment. This -pretty clever- device could allow us to travel with just one empty can and a small portable bicycle air pump. Saving us the trouble of carrying or sending the gas cans abroad by flight. With the advantage of being able to re-use it even without a electricity dependent air compressor to fill it up. Thank you for this video!

[@highlandspiper8838]

@Etienne Dubois Yes we get it. You know sometimes you can just let a idea be good for what its good for, and not try and shit on everything that isnt to your standard or wasnt your* idea.. My God, go find something else to do and quit trying to nay say everything .. I know this may come as a surprise... but we really are smart enough to know that this is makeshift way to get a few seconds of air for indoor projects where you need a quick burst of air but dont want to bring a huge air compressor in the house- and dont have a fluorocarbon can available. So I know this may come as a surprise, but you dont have a monopoly on realizing somethings limitations... RME

[@MrMedico33ER]

to be economic: goes well equally fill the can with a manual inflator for bicycle?

[@kiyoponnn]

Yes, but it requires some muscle

[@Simon05784]

Muscles we have. Wondering can one refill at the original outlet? I am thinking for an airbrush compressed air can?

[@mobbdeep615]

@@Simon05784 ok yoda

[@davy2748]

Smart done, do you have already an idea how long you can use it b4 it fill with water from the compressed air? with compressor you have a valve to let out the water afther a time. special for computer components is water not a good idea .

[@snellataurrisrex9388]

2:48 Its like the can made a dash for freedom “RUN!! - I’m single use you psycho!” 😂

[@jasmun5550]

😂

[@neodiy]

BTW how many PSI max did you pump into the can? I made one but i am not sure how much pressure to pump fearing the stem tube going to become projectile

[@stayfrosty1323]

How does yours work? I made one but it doesn’t even go past 10 psi before the air compressor shuts off.

[@neodiy]

@@stayfrosty1323 wow ...thats superb because mine goes up to 30 psi when i blow the air out it takes only two times to finish....by the way how did your air compressor auto shut off? mine doesn't it keeps pumping if i wanted to...but i am just afraid of the unknown danger of being naive --- i meant pumping it like no tomorrow

[@neodiy]

@@stayfrosty1323 BTW i dont think you pump only 10 psi it could be 10 bar because 10 psi is almost nothing to blow

[@Dancopymus]

Good design! How to know the air pressure fitting on the container? Thank you

[@tejahara1304]

You can fill in to a maximum of 7 atms(Atmospheric Pressure) but Because of Safety you can put in 3 to 4 atms...

[@PackardBelltoll]

so would u say that is 32 min 42 max?

[@neodiy]

you are incredible this is what i am looking for you are da best man...cheers

[@jangajunga7839]

Awesome! I am managing to use an Acme Air pressure cleaner CL51, is it suitable for your great project?

[@nicholaslombardo9696]

How many psi

[@Rose-ec6he]

Looks like 10 bar is the max before it explodes but but 5 bar should be plenty. That's about 72 psi. I'd go with that for safety.

[@torukojinnn6331]

Dude , you are a genius

[@jonnyloco6766]

This is exactly what I wanted to learn how to make. Great video!

[@fixitsamo]

+Jonny Loco Thank you

[@Yhapetsz]

very Good idea but try to hold the fan of the videocard while cleaning it may damage the card when it spins.

[@MrDoboz]

damage the CARD itself? is it the voltage generated? well, i never thought about it..

[@xeniq571]

+MrDoboz It "supposedly" damages headers on the fan, though I haven't had problems with it

[@nicksmith1363]

Wonder if throwing a few desiccant packs in the can before adding the valve would keep moisture from the compressor from getting in your electronics?

[@cbearabc]

Water should settle in the bottom of the can

[@eksine]

your compressor is supposed to have a water/oil separator on it anyways, it's seriously like $4-6, are you really that cheap?

[@Rangermanlv]

Eksine you are a moron and your comments on a lot of other people's comments in here just prove that. As far as moisture getting into electronics it's going to depend on the humidity in your area how much moisture gets inside the can and how much of it actually ends up coming out when you're using it to blow off electronics. Most companies use a form of ethane gas in these canisters because it's easily freezable and stays liquefied under room temperatures and this also has the added benefit of it almost completely evaporating as it expands and leaves the can. It should also be noted that this way of recharging a compressed air can is not going to have nearly as much air in it as an original one would. Good idea but the video needs more information about the process and what benefits and drawbacks there are to it.

[@mukeshpandya4171]

I love when people re-use and refurbish... instead of buying new every time. Thats a nice project.

[@fixitsamo]

+Mukesh Pandya thank you

[@EnergySeeker]

what PSI do you fill it at ?

[@Ahmadsyar]

2:48 jumpscare

[@ShutupNerd]

air duster manufacturers hate this guy! just follow thus easy steps...

[@eksine]

just go back to school to learn how to spell

[@nel6745]

eksine you didn't get it did you

[@eksine]

Hexed you don't know what a joke is do you?

[@sealifett8395]

The only downside is moisture will accumulate in the can.Air dusters use freon a dry gas

[@venkoshop4124]

can you suggest any way to prevent the accumulation of moisture??

[@sealifett8395]

@@venkoshop4124 Use an inline dryer for the compressor

[@briholt100]

@@venkoshop4124 another alternative would be to take out the little valve core. That would basically open the can to ambient air pressure and humidity. Of course, that would then de pressurize the can. That might be okay. I'd probably fill the can up with my compressor out in the garage. Then I've got a portable can for the day. When done, let it all out

[@markjones2349]

@@briholt100 Not quite a day buddy. More like a can for 5 seconds.

[@briholt100]

@@markjones2349 you bet, little one.

[@jazz9322]

Can I use a manual air pump for a basketball? I can't afford an automatic compressor.

[@fixitsamo]

You can use any manual bicycle hair pump i used a compressor in the video just to speed things up

[@jbocaneg17611]

AWESOME!!!! This is what I am going to do right now.

[@adarshshamloll2367]

Will it explode afterwards, because I heard that it exploded in some cases?

[@robindaniels8920]

Hi! Nice DIY! But can you place the valve at the bottom? Is it strong enough?

[@fixitsamo]

+Robin Daniels Sure but it will be hard to put it standing on a shelf

[@chessguru900]

I used this technique to make an aircraft and it worked.

[@eksine]

a blimp? anybody can do that, it's called a happy birthday ballon at walmart $4

[@ruchan_kaan]

Is there any reason to drill up top, near the handle? And how do you be sure its filled with enough air, before explode :)

[@barnabyvonrudal1]

I saw another video where they drilled the bottom part because the metal was thicker than the other partsl

[@ashutoshvenkatraman8889]

2:48 , came running to comments after seeing it 😂😂😂😂

[@jord9261]

overreaction much

[@ashutoshvenkatraman8889]

@@jord9261 fuck off dickweed, I react how I like to.. is this appropriate reaction?

[@jord9261]

@@ashutoshvenkatraman8889 insecure much

[@ashutoshvenkatraman8889]

@@jord9261 snowflake much

[@ownerfate]

This combined with the spray paint gun is EPIC.

[@mohannadalmadanie4425]

very nice project MR Ehab go ahead

[@jakubkaczmar2917]

Can you mix air with chili solution for self defence and use it as a spray?

[@useitwice]

Jakub Kaczmar that actually sounds like a pretty good idea. It should work. There are videos of people making refillable spraypaint cans

[@beau3s]

if you filled the can with propane gas or butane gas and put a lighter in the trajectory of the spray, you can make a flamethrower

[@paulw.1008]

this is a good way to blow your hand off.. thats essentially a pipe bomb.

[@kiyoponnn]

Yes, but it's dangerous

[@omkar2571]

i have some questions: i have air freshener, how can i make sure that the can is fully empty? and if i use that air freshener can is there no harm to my motherboard ?

[@sunilwarade8693]

simply superb..... and environment friendly....

[@fixitsamo]

+Sunil Warade thank you

[@lytnin88]

I don't see how that valve can be airtight and not leak. Seems like you'd need to seal it with silicone or something. How long would it hold the charge?

[@JamesR5D4]

The compressed air inside seals the valve rubber against the can’s inner face, making it airtight 👍🏽

[@venkatasubbaiahbhuma997]

Up to what pressure can fill

[@cartemiocartemio]

hi! how many PSI did you charge?

[@daVidFonda]

Yeah ! Up to how many psi in the can, please ?

[@tejahara1304]

you can fill in a maximum of 7 atms but Because of a few safety issues 3 to 4 atms will be fine

[@daVidFonda]

Thanks Teja

[@tejahara1304]

Google it

[@macgyverb.4307]

how much psi you think the can can handle or max i shoud put

[@Rose-ec6he]

Looks like 10 bar is the max before it explodes but but 5 bar should be plenty. That's about 72 psi. I'd go with that for safety.

[@JulioGonzalez-vm1vg]

How much pressure do you put in?

[@akshjalal893]

omg great idea excellent work man nice invention

[@fixitsamo]

+Aksh Jalal Thank you

[@luisfj9]

Thanks for the idea I tried building one myself inserting the valve into the can was a b**** but otherwise it was a success but I would recommend that anyone who tries to do this have very good strong hands to this type of a modification.

[@tylonbarnes9678]

where can I purchase that air valve like the one that you have?

[@fixitsamo]

At a tire repair shop this valve it for a tubeless tire

[@sumgai7]

Just FYI from my first try on this: trying to twist the tire (tyre) valve into the hole, even after sanding it a bit: the edges of the hole are still very thin alumin(i)um, which bit into the rubber of the valve, and cut it like a corkscrew-in-reverse, destroying it. Fortunately I have one more -- I bought a 2-pack from Amazon - but am going to be MUCH more cautious trying #2. I'd certainly suggest some lubrication (Vaseline/petroleum jelly) to help squish the thing in, which I'll try. Also I think the drill size of 3/8" is a bit small, as the standard hole size is actually 11.5mm (.453") and 3/8" is .375" -- the 11.5mm hole is almost exactly 29/64 drill bit size in the Imperial world, a good bit larger than 3/8! - I'm going to enlarge and try again.

[@spacejihadist4246]

The can bottom is a lot thicker.

[@fixitsamo]

@spacejihadist4246 not practical for storage

[@potassiumchloride2542]

WOW thx for the useful video. You should make more this kind of video!!!!!!

[@fixitsamo]

+lau Jenn Yue Thank you

[@vladislavroytapel2830]

COOL ! What compressor do you use?

[@fixitsamo]

I used a 5 gallon compressor just to speed the video the real idea it to use a regular manual bicycle air pump Cause what’s the point of this video if you have a compressor 😉 thx and good luck

[@zawazat]

صوتك مو غريب ،، كأنك ايهاب من قناة ايهاب بلانت ، شغل عظيم شكرا لك

[@DevFTW]

هوا نفسو

[@zawazat]

@@DevFTW تمام تمام يعطيك العافية

[@wiltelemaco5782]

hey, excellent idea.

[@fixitsamo]

+Wil Telemaco thank you

[@Msaif-el4ts]

Can you make it with 3 inches bottle or can etc

[@MrIMacro]

Any can can work?

[@Jestr86]

I'm sure the valve doesn't have to be that long, there are shorter valves..

[@athafawwazrudiyanto5966]

You know, when the title says DIY then you can try it yourself with the best component you can find

[@rweakley]

Nice hack! I'm gonna try this :)

[@sunithareddy3154]

I'm using a perfume bottle and drilled a hole in the bottom and just fixed a tubeless tyre valve into it perfectly without any leakage , but there is a problem, its not keeping the air inside the can and the air is leaking through the spray nozzle even if it is not pressed so can you plz solve my problem🥺😕😕🙏.

[@Rose-ec6he]

I think you can only use aerosol cans. Most spray bottles aren't designed to handle any pressure.

[@ailefy9898]

@@Rose-ec6he Thank you:D

[@PackardBelltoll]

I need to know the size of tubeless valve used in video TR18?

[@sambking]

Another great video! Thanks!

[@fixitsamo]

+sambking Thank you

[@whatshername3158]

i'm actually lookking for a way to process compressed air to clean my carseats clean of dirt.is this is powerful enough to extract humid dirt out of the seats and onto a cloth like a real air compressor or is the pressure lower?

[@eksine]

compressed air would push dirt into the seat, not good. just goto a car wash and use their vacuum for $1, use a spray bottle with some dish soap and water to get the seats wet and keep vacuuming. those machines have good suction. again do not be stupid and blow air into the seat, that is fully retarded

[@Anonymous-tk9re]

Bahahahaha

[@bentalebtouhami]

Thank you

[@fixitsamo]

+touhami bentaleb You are welcome

[@AtlasReburdened]

That's fine and good, but you need a water trap on the inlet of the pump or your spray is going to be super humid. Might not matter for your application, but it might.

[@AnoNymous-dh2sv]

It matters the most in that application, because it's electronics, and water is the first thing they hate.

[@8Wolfslain8]

I have no earthly idea how you managed to stuff that valve in a 3/8" hole without damage. I stuffed mine in alright, but it cut the rubber bad enough that I'm not keen on trying to fill it up. Do you think a 1/2" hole would be too big?

[@fixitsamo]

+Welshtyn Heglund 1/2" is to big Did you use the same valve that i used ? Cause the 3/8 hole should be perfect You have to take your time when installing it i suggest using sanding paper to enlarge the hole and to have a softer surface

[@8Wolfslain8]

fixitsamo /// Exactly the same brand, same size as well. I tried a second one with a slightly larger hole and it worked better. Drill bit was about 7/16" I think. Functioning well. Hard to know it's pressure limits, though.

[@dragon940carp6]

The ones I've seen use a hole at .453".

[@pandora6498]

Hey, I am trying to make a model of geothermal power plant but air pressure is not that much high to spin the turbine so,I searched on KZbin and found this video and I want to know if I could use this in my model to increase the pressure of the water vapour..... Please help....

[@deletedperson2072]

Yes

[@mcliff8719]

KUDOS! Thank you. Very nicely done.

[@namly9868]

THANK YOU VERY MUCH

[@saltysenpai4216]

How much PSI?

[@haniko1236]

Good question for an unexpected bomb lol

[@raghaf2007]

4-5 is safe

[@eksine]

As much as the bicycle pump can give you, too much pressure will just leak out. no bomb

[@luisjaviergutierrezjeronim4883]

How much pressure can I put in a Sabo duster can? I already put the valve...

[@Yoyo378]

Less than allowed for the same container. en.wikipedia.org/wiki/Gas_duster I would recoment less that this 10 PSI they are talking about coz your can structural integrity is compromised and you dont want a rubber valve to hit you or somebody when it will shoot out.

[@AtlasReburdened]

The rubber valve isn't really the dangerous part. Explosive decompression + thin sheet metal = Missing fingers.

[@highlandspiper8838]

@@AtlasReburdened compressed air will not be enough to fragment that can and take off finger. That can would separate at a metal seam and lose what little pressure it had ..the thin metal is to pliable and would simply rupture and split or blow a seam out or more likely blow out at the weakest point the valve would blow out. I do imagine it could hurt you of the valve was blown out into your or another's eye, and it could theoretically cut you when it split, but I doubt it...I would imagine however that it would scare the Sh*t out of you when it popped.

[@PackardBelltoll]

I think you can add some sealeat weld

[@saritanhjsirat1195]

TBH, this video is supposed to be cheap and not doing any soldering whatsoever if you want to you can put epoxy or moldable putty that can withstand high amounts of pressure

[@vladislavroytapel2830]

Etienne Dubois Do you know safe alternative solution to fluorocarbons ?

[@dennisshaw1195]

I use a hair dryer on high

[@ericd2791]

I tried this didn’t work, doesn’t hold pressure for long. Leaks out

[@tonysony1351]

It worked for me perfectly make sure the you sand well to get a smooth surface

[@KynnessNuve]

sir how much the pSi of this CANISTER to make sure is not over blown?

[@KynnessNuve]

i reply my own question i input air for the 3psi which is good, but only problem is that the air inside not run long, it will take only around 8 seconds and finish, unlike the new buy condensed air, you can still use it as long they have liquid inside the CAN, but refilling AIR, not run for long and only use for blown dust small portion... only i can suggest buy a new electric air blower and use it much you can do, just click the switch that's it...

[@truedesireelements2040]

oh okay

[@tanpeke]

those cans comes from factory with 20 PSI

[@KynnessNuve]

thank you..

[@gokhankocu3991]

how many psı ?

[@feidex]

ranger yea whit spray paint is from 90-120 but better do 95 so can a bit safer and it will not explode

[@gokhankocu3991]

Thanks ;)

[@eksine]

it can't explode anyways, that seal from the rubber valve is mediocre at best. if you try to overfill it it should just leak or blow out the valve

[@adnanal-saffar5473]

DONT DO THIS AT HOME u can have a serious injury be sure the air dust completely empty cause its so dangerous to drill a whole if there is a pressure in the cane . you also have to be sure whats the max pressure for the cane or it will explode

[@666hobart]

+adnan alsaffar Don't cross the road! you might get run over!!

[@highlandspiper8838]

Sure if you sit there and watch the can swell at ungodly pressures it may explode..RME, snowflake..if you use your common sense it will be fine...BTW if you had any clue you'd know the can wont explode but will simply blow the valve out before that happens or will separate at a seam. ...Your theory is bumpkis fear mongering not based in fact.

[@muncom088]

Good idea!

[@ee99419]

What is the maximum psi that you should fill it up to?

[@tanpeke]

those cans comes from factory with 20 PSI

[@benhansford8524]

How do you fill it with DE dust?

[@silversand08]

Excellent idia

[@fixitsamo]

+silversand08 thank you

[@greatnew_products7436]

It would be an excellent IDEA to know how to Spell..

[@hoping_best]

👍well done

[@fixitsamo]

+M saqer thank you

[@realusuck]

HOW MANY bar TO MAKE THE CAN BOOM ???????????????????? 0w0

[@Rose-ec6he]

No. You can't liquify air at room temperature. It's just compressed to more than 1 atmosphere.

[@Ahmedkhaled-ev1jw]

The maximum pressure is usually written on the can

[@Rose-ec6he]

@@Ahmedkhaled-ev1jw On aerosol cans?

[@ПавелЕпифанцевъ]

15-20 bar

[@mochansidar1639]

Thanks for this

[@xxoustou]

Mice job.well done

[@fixitsamo]

+xxoustou thank you

[@greatnew_products7436]

If Mice could work, he would give Mice jobs...

[@xxoustou]

Very clever man

[@JohnPaulBuce]

now how to make a compressor at home

[@Hanesy]

I like this video. thank you. 😊

[@grahammillar8012]

Just a precautionary suggestion. Unplug the fan. Doesn't take much to damage a video card from current created by circulating the fan . Ideal situation remove fan and clean fan and fan blades with a dry tooth brush .With the heatsink a quick blast of air should suffice. Wear an anti static strap when handling circuit boards for added protection :)

[@VSPhotfries]

Isn't the fan on a different circuit past power management? I can't imagine even a rather low-end card being built with the fan having a direct, unprotected connection to the other components...

[@eksine]

the fan will just stop. I doubt it would be permanently damaged. but I do agreed just turn off the computer first, it prevents you from touching the power supply or a capacitor and killing yourself. the fan is the least of your worries

[@feilox]

How many sprays do i get?

[@fixitsamo]

+Fa Vang if you keep you finger on it it will spray around 10 seconds

[@highlandspiper8838]

@@fixitsamo Its best used in short bursts anyway..and simply fill each time you need to use it. I still use commercial compressed Flor cans but this is a good back up when you dont feel like driving to store for damn can .....its a good back up..

[@tylonbarnes9678]

I don't have air compressor at home, may I Use a bike pump?

[@fixitsamo]

That’s the idea is to use a manual bike pump I used a compressor cause i didn’t want the audience to wait long time

[@AllenHanPR]

Audience? Aristocrat I see...

[@RBRM3]

Why not get an actual heavy duty can and add the quick connect and a pressure valve? I made several before making one that can handle (300 PSI!!) Insane I know but this thing blows my 50/50 concoction 20 ft.. Otherwise is a very thick can about 10 years old made of titanium but I will use it forever! I love making shit from nothing..

[@MasterhpIke]

That's a compressed GAS can.

[@fpvcaldy6683]

Anyone else watching this cus there pc is full of dust

[@CPS2]

Their*

[@rice9380]

because*

[@faslaiqbal628]

Yes

[@sharuiihearts4372]

Yea

[@Rose-ec6he]

@@CPS2 Their*.

[@cr82009]

What you need to do is try this in a device that is sold on Amazon, an air compressor that works by charging, it has an electric battery, and its power is excellent

[@invertedstar4355]

link? Or name please

[@athomenotavailable]

@@invertedstar4355 just search for electric tire pump

[@rogue_spirit]

Thank you ihab :D

[@АннаСвечникова-ы2щ]

It's great ))))

[@fixitsamo]

+Анна Свечникова thank you :)

[@ilias4711]

+fixitsamo Hello, it looks like an nice idea . I don't have a compresor , can I use a compresore at a Gasoline Station wich is used to fill up tyres with air ? Or will be the the pressure too high?

[@fixitsamo]

+ilias4711 you can use a manual bike tire pump

[@ilias4711]

fixitsamo Thank you very much.

[@NikhchansGaming]

What if I don't have air compressor.

[@fixitsamo]

+nhs2008NC The idea of this project is to use a manuel bicycle pump to refill I used the compresseur in the video Cause it was faster no point of making this project if u already have a compresseur

[@NikhchansGaming]

fixitsamo Thanks. i don't have that too.. But I can get one. But After refill, it'll be air right? means it won't last as long as the real thing?

[@fixitsamo]

+nhs2008NC Welcome if you keep your finger on it it will spry air for around 20 seconds straight b4 you have to refill it again

[@DBronk22]

But then i don't have anything to get high with

[@GilZu]

I hope you're not really using that ancient card

[@klogjo]

Combine with your paint spray gun and there you go, THANKS

[@eksine]

no enough pressure or air volume, no thanks. spray guns need a 21 gallon compressor or more unless you're using a mini gun or airbrush

[@DavidWahlstrom69sins]

But how is it gonna make me walk on sunshine?

[@DBronk22]

Sry man

[@totalnattybruh3517]

when refilling the can, you will know it is full when the can explodes in your face...DIY tip

[@MARWAH27]

Go how much pressure of air in the cylinder.

[@ok5948]

إيهاب ليش ماتنزل بالعربي قناتك للعرب طبخ بس 😢