DIY Exhaust Tip/Tailpipe

Рет қаралды 200,432

GP Garage

Күн бұрын

Пікірлер: 47

@protomanialab 7 ай бұрын

You are a wizard 🧙🏻‍♂ This is a good lesson of mechanical handicraft! Thank you friend!

@azharsalim2028 7 ай бұрын

Great job... however, in the first part of the laying out process, he need not take the trouble to calculate all those "pies" etc.... just take a piece of paper and wrap it around the pipe and mark the circumferemce. Then just divide it by the number you want.

@irvingcobian 6 ай бұрын

Good info!

@berndheiden7630 6 ай бұрын

Easier: just fold the paper 3 times in half to get the 8 stripes!! 2/2, 4/4 and 8/8! No calculation at all!

@kevinsmith3935 7 ай бұрын

Lovely bit of work , what are the discs you used on the angel grinder to clean welds and Polish the stainless please

@GPGarage1 6 ай бұрын

Thanks, for cleaning the welds I use Pferd Polifan A40 SG, after that sanding discs p80, p150 and p240 than polishing with some "no name" stainless polishing kit (polishing pad and blue compound)

@Payns83 5 күн бұрын

Magnifique travail 👍

@muhammadalfin2891 7 ай бұрын

Very neat workmanship, greetings from Indonesia

@tonimerklin122 7 ай бұрын

Thank you for your videos and knowledge!

@RustyInventions-wz6ir 6 ай бұрын

Nice work. I’m sure I’ll have to do it myself at some stage

@GPGarage1 6 ай бұрын

Thanks

@jean-pierrepannierdesrivie4406 7 ай бұрын

You are a very good teacher !!! Bravo !

@nickmarshall9192 6 ай бұрын

Excellent work Not perfect But still excellent 👍👍👍

@guytech7310 7 ай бұрын

Pretty Neat method. Thanks for sharing!

@JoliettesParadiseAdventures 6 ай бұрын

Looking great!

@arneminderman3770 7 ай бұрын

Wow! ❤❤ great video

@thedude5869 6 ай бұрын

Nice job !!

@charlescamilleri3323 7 ай бұрын

Very nice and prof. job weldone

@ИгорьСмирнов-у1в 7 ай бұрын

Красиво. Но почему без поддува?

@Rainer1992 7 ай бұрын

Das sind einfach skills Wahnsinn ❤

@stiefbeen22 6 ай бұрын

Another approach could have been using a cone of cardboard, like kids have on their head on their birthday. Using the larger diameter as the base and the smaller one up as high as the length you want between the 2 pipes. Cut it at that point horizontally and use the lower part on the stainless steel. Only welds will be on each end and the closing. Less welding, less polishing.

@timmyb1874 Ай бұрын

This is amazing.

@HerbertHaag-l1f 7 ай бұрын

👍 super Video 👍 thank you

@dimashilov8139 7 ай бұрын

видео немного затянуто, но познавательно 👍

@jonathansantosdeleon9690 Ай бұрын

Realy nice

@michelbalts6064 7 ай бұрын

Magnifique....merci

@moarif9139 6 ай бұрын

that's awesome

@jochetaman23 5 ай бұрын

dude,.,.u no joke

@jsmith9970 2 ай бұрын

Well if you made $1.95 per hour this would be useful instead of spending the $29.95 to just buy the flared exhaust pipe from the internet.

@oliverstaudinger5003 6 ай бұрын

Genial Einfach=Einfach Genial

@MasterPKW 6 ай бұрын

А то что заржавеет через полчаса никого не смущает?

@GPGarage1 6 ай бұрын

No, it won't.

@ianrace4066 7 ай бұрын

A cheap pipe expander is easier and doesn't take 8 hours of Fab and you don't need a welder.

@GPGarage1 7 ай бұрын

Of course, there is an easier way to do this, but this is a DIY project that anyone with a welder can do. Also in this case the difference in pipe diameter is 30mm, so cheap pipe expanders would hardly do the job.