DIY Force Feedback (FFB) Sim Wheel - MMos Firmware

[@leopardbeau3657]

drive.google.com/drive/folders/16qBwewArJznSIwluOPdM2UJBk7X2ITAH?usp=sharing

[@Thomas-rg8nt]

@Archie Enoch You really made 2 accounts for a scam?

[@knivessurvives]

@@Thomas-rg8nt how is it a scam?

[@Thomas-rg8nt]

@@knivessurvives the replies I was referring to are long gone now

[@bgis6409]

Nice design , I hope you get it where you want it to be as far as power/strength goes.

[@djavanramires4293]

Ficou top esse projeto muito bem feito...

[@reviewforthetube6485]

Very clean and very nice can tell it picks up on alot of detsil which is great and what matters tbh lol

[@domainexpansion6438]

Hi i love how it looks. Its very minimalistic and clean I will build one myself hope to succeed

[@leopardbeau3657]

thanks! good luck.

[@birdyos6303]

Product list please!

[@yusufkaplan5014]

Very Nice!! Design is perfect

[@leopardbeau3657]

thanks!

[@many12379]

Hi! I want to rebuild my steering wheel, and make it based on 2020 aluminum profiles. Could you tell me if this kind of construction would have enough strenght to work with bigger motor like 1016 24v dc motor?

[@stroymoney-lr7nb]

Bro please tell me what number of revolutions and what voltage on your 895 engine will help a lot

[@leestow1]

How did you attach wheel to 12mm shaft? I'm having trouble finding a way to connect the wheel to 12mm shaft.

[@kanyaahshopid5758]

Awesome project

[@geforcy]

Wow Nice!! Keep this one in mind

[@walter_46-p7l]

top demais !!!!!!!! perfeito !!!!!!!!!

[@leekahyao9680]

where can i find the encoder bracket?

[@Felixnelsonsr]

What is the advantage of the STM32 over arduino leonardo is it has more effect or something like that? Or just the same

[@GAACALORI]

Qual motor seria esse? Alguém tem o link do motor?

[@Luca-pg5mj]

Hello, but using the ffb on the steering wheels nn you go to wear out the brushless motor?

[@markh4233]

感谢谢谢老铁的方案 给力

[@BMRX1000]

qual motor vc usou ?

[@DaStuntChannel]

how's the torque??

[@burhanisk7460]

Power supply?

[@JacekTheKing696]

Hi, I have a problem with connecting the motor (it is 3 phase), are you able to help me?

[@justsheeeps134]

Connect 5v with 4.7k ohm resistor to a and b wire if im not mistaken Go read em at web

[@theflamethrower867]

U need an esc

[@ruwanthusithakumara1535]

full videos Very nice 👍

[@jayveemagtangob6527]

item you use??

[@hoangphucle8178]

So beautiful bro🎉

[@ryder5957]

Opa, quais são as medidas dos perfis de alumínio usado?

[@okangulel583]

Very nice 👍 Could you share the circuit diagram?

[@baihaqiabizar]

yo where did u get that gear and pulley set and also what size are they? thanks

[@JonathanST_94]

Motor only turns to one side and does not receive orders from the pc in Disable the motor continues to work and does not stop

[@Riley_Christian]

Can anyone help me figure out how to use a stepper motor instead, I already have one (and the stepper driver) and know how to drive it with and arduino, but idk exactly how to set it up. Any link would be appreciated I wanna do it cuz the stepper I have its way heavier duty than my dc motor

[@poison2561]

did u do it?

[@Riley_Christian]

@@poison2561 I think I found an open source project for it, but the steppers I have run way too hot anyways cuz there cheap. I ended up using them for some other projects. I have a brushless motor that's stronger than a logitech wheel anyways

[@yaserexe1361]

What is the profile size you use here 20x20?

[@leopardbeau3657]

150mm x4 110mm x6

[@gamingnoobxp6518]

awesome. please can u translate in English(Documents)?

[@sket123flamez7]

hi will i have a more accurate if i use 2000P/R encoder

[@nategamertv715]

yes lmao but all you need is 1000ppr anymore then i think you might be wasting your money

[@bogia3278]

How many revolutions should I choose for a 775 engine?

[@duongcaoquochuy3634]

895 = 0.5hp đủ lực kéo

[@yekte5823]

Compatible for all games in pc

[@ThomasLancheros-kg1nl]

No only certain games

[@antinoriberenice]

Clean AF

[@serhatozcan3624]

Did you do the pedals? If you make it please share with us :)

[@leopardbeau3657]

Yes. I used the electronic accelerator pedal of the truck and fixed it to the wooden board. LOL

[@viniciusschmidt9050]

do you have the link to purchase this motor?

[@fitchyyboi]

Just any brushed 550 motor around 30-40 turns

[@akiraho8727]

你好，我想問問這個2020架的尺寸大概是多少？

[@akiraho8727]

看到留言了

[@kakametallicas]

Por algum acaso ja saiu fumaça nesse seu motor?

[@korasukaro7794]

Hello bro... Whats size profile alumunium did you use? Is it 20x20 or 40x40 please answer.. I want to build...

[@leopardbeau3657]

20x20

[@domainexpansion6438]

wiring ?

[@tardraker4631]

Mi problema es el BTS7960, el motor aveces no gira o sólo gira hacia un sólo lado sin parar, he revisado la conexión muchas veces, no se si sea la fuente de energía

[@leopardbeau3657]

我认为接触不良的可能性比较大。

[@eduardomartinez2890]

Really nice project, however i would like to know if you had any problems with that motor, because i have a 1/5HP version of it installed in a tiny belt Sander/Grinder and if you overload the motor for about 20-40 seconds It will already start to smoke. I Hope your motor and the motor from anybody that made this is better quality than the one i have.

[@chuoique]

Pulley ratio between motor and shaft, what is best your choice?

[@leopardbeau3657]

16:100

[@tribilin905]

Budget?

[@rhsuper3653]

The delay between the applied movement and game is huge!

[@kemalayyldzart8272]

nice design

[@leasher9383]

What is the pulley ratio between encoder and shaft?

[@leopardbeau3657]

2:3.

[@ahmetmkl]

It looks very nice. What are the dimensions of the profiles?

[@leopardbeau3657]

150mm*150mm

[@gilsonladeira9783]

very good, works on Ps4 gran turismo sport?

[@mockingrebel9949]

Do you have a power supply (if so which one) or does it just plug into the usb port and work

[@leopardbeau3657]

Yes, power connected to BTS7960.

[@zaenalchandra2692]

Nice....👍 Ampere on your power supply?

[@romansoucek7041]

Is it work on Playstation??

[@yoandeul9297]

I don't think so

[@kai_5103]

can share the material list？

[@leopardbeau3657]

Sure, but this BOM is from Chinese.Can you read it? drive.google.com/drive/folders/11Q05vrSxl5t7WqdTu-qmqPeWHpCtHbTM?usp=sharing

[@onurkiyak23]

which power supply did you use?

[@mb-ls5vw]

Hi congrats clean work. but can you share wheel hub pls :) I couldnt find it in the link you shared

[@leopardbeau3657]

Link in the BOM folder.

[@baas7914]

@@leopardbeau3657 How long the belt on Motor DC and encoder

[@norbertsvab]

Hello what is your psu?

[@joskotze4193]

Hi. I want to build a wheel like this. Do you have a list of parts that i can buy.

[@leopardbeau3657]

I hope so,but I bought them from taobao.

[@hahmetsurucu7127]

You are great mate! Great job! I have a question, i don't want to use ffb so i don't need pulley etc. I just want to use that rotary encoder by attaching to the wheel. So my question is how can I attach the gib with the shaft which is on the encoder? Thank you!

[@leopardbeau3657]

drive.google.com/drive/folders/1h9Kf2uG8SofxEXkD7mLCPCDGTvzPhjiD?usp=sharing

[@mahmudnazimbinshamsulbahar2201]

he used a shaft coupler

[@karel88l]

I want ask which motor are you using ? It looks like RS775 DC motor.Are you satisfied with force feedback with this motor ? Is torque smooth ? I am going to build FF joystick an I am considering to choose BLDC ord DC motors.

[@leopardbeau3657]

895 DC motor.Entry level experience.

[@karel88l]

@@leopardbeau3657 And how much torque can this monitor produce ?

[@joskotze4193]

I am also interested in building one. I would also like to know how much torque it makes. I think anything above 0.3nm wil be nice but id prefer above 1nm torque

[@Sithhy]

@@joskotze4193 Search for 24V motors with over 1A & with up to 8000RPM max. Those will give you 0.08 - 1Nm torque directly on the motor

[@MultiNillz]

Im thinkinbg of making a build like this, but im pretty new to the stm board, is the firmware free? and how many inputs does the stm board take? As in can i hook up an H shifter and pedals to it as well? And how is the torque with that motor? Im planning on using a PC psu with it.

[@leopardbeau3657]

The firmware is MMOS and is open source .It cost about 600 RMB in total .The torque is relatively small, about 1nm.

[@MultiNillz]

@@leopardbeau3657 Thanks for replying :) i found VNM Simulation firmware as well, seems to be in active development and is free, did you try it yet? Im having trouble finding any pinout sheets for the stm board on how many potentiometers and buttons i could connect to it.

[@leopardbeau3657]

@@MultiNillz Not yet.There is a wiring diagram in the top link about MMOS .

[@kein_engel_zlat]

Hi! Tell me, please, what is the gear ratio in your steering wheel? 1:3 or 1:6? Or something else? And I understand that the 895 engine, BTS7960, STM32 and encoder are used?

[@leopardbeau3657]

1:5. You are right!

[@kein_engel_zlat]

@@leopardbeau3657 Thanks for the answer! What does force feedback feel like? Is the force feedback force comparable to the most common steering wheels (Logitech G25 / 27 / 29, Thrustmaster T150/300)? And most importantly: what is the chip marking on BTS7960? GAG523? P.S.: I apologize for my bad English.

[@leopardbeau3657]

@@kein_engel_zlat week.LOL.Very weak compared to direct drive.

[@leopardbeau3657]

@@kein_engel_zlat Sorry.I don't have G25/27/T150...

[@leopardbeau3657]

@@kein_engel_zlat GAH923.I think it is not important.

[@domainexpansion6438]

Hi i really need to know are you using pull-up resistors for the incremental encoder?

[@leopardbeau3657]

YES. R=1K

[@domainexpansion6438]

@@leopardbeau3657 Thank you

[@claudiorobertoferreira992]

Olá bom dia, você poderia detalhar mais este seu projeto, ficou muito bom e gostaria de reproduzilo. Vi ali que você usou dou arduinos, poderia me dizer o porque? Fico no aguardo do seu contato.

[@leopardbeau3657]

你好！ 这个是STM32F407方案，使用的是MMOS固件。

[@RRodrigues18]

Amazing job Small clean... The motor is strong enough?

[@leopardbeau3657]

maybe not..

[@skaf134]

Bro, what encoder have you used on your DIY steering wheel?

[@aykutyurtsever1181]

nice design, did u design it before buying the parts ?

[@jeralddcruz7325]

Hi can you teach me how to wire ffb steering wheel using stm32f407vet6? I don't want to use arduino cause it's a bit of laggy i am very willing to pay please help me or give me schematic i will pay you thanks

[@erkanesen7319]

encoder ppr is how much ? ( i mean like "600ppr & 1000ppr..." )

[@erkanesen7319]

and are you use the power supply ? i see just ardunio usb,

[@leopardbeau3657]

600 of mine.1000 better.

[@leopardbeau3657]

@@erkanesen7319 DC 12V supply.

[@erkanesen7319]

@@leopardbeau3657 can we use 600ppr or 1000ppr encoder a get like 360 - 420° ?

[@leopardbeau3657]

@@erkanesen7319 Yes. The encoder can keep turning, which is different from the potentiometer. The degree is set by the software.

[@yonashoo503]

Nice project. Is it better than T300 or T500 in feel?

[@leopardbeau3657]

Maybe not

[@hudaif1451]

super neat good work cost ?

[@leopardbeau3657]

500RMB ≈ $75 today.

[@hudaif1451]

@@leopardbeau3657 thank for the reply

[@dogkansarac4889]

which mm shaft did you use? it looks like 10 or 12mm

[@leopardbeau3657]

yes 12mm

[@dogkansarac4889]

@@leopardbeau3657 is it enough to encounter force feedback? I was planning to have 16mm

[@leopardbeau3657]

@@dogkansarac4889 yes

[@domainexpansion6438]

What did you use to mount the wheel?

[@leopardbeau3657]

FR4

[@domainexpansion6438]

@@leopardbeau3657 Thank you

[@wangfeng175]

GREAT!

[@eraygunaydn9961]

Hi bro good job, is there any step file or sth? I cant read Chinese sorry :)

[@leopardbeau3657]

Sorry too.I am not good at English LOL

[@F2PAdictt]

Hyy bro what encoder u use?

[@leopardbeau3657]

ROTARY 5~24V 600 pulses

[@TheJorensanbar]

Amazing build! You are using STM32 or Arduino Leonardo? BTW... RIP HDD of that Laptop :P

[@leopardbeau3657]

thanks! That is STM32.

[@lss247]

Very clean but I wonder how much power it can deliver. In newtons. Good job, anyway.

[@jeralddcruz7325]

Do you feel any delay using that encoder?

[@leopardbeau3657]

It is determined by the MCU, STM32F4 is very fast.

[@jeralddcruz7325]

@@leopardbeau3657 can you please give me the firmware for stm32f4?

[@leopardbeau3657]

@@jeralddcruz7325 drive.google.com/file/d/1zaopNTy6wPTmPb68tP6k-3PSSNlW29PF/view?usp=sharing

[@jeralddcruz7325]

@@leopardbeau3657 thankyousomuch is this for the stm32f407VET6?

[@leopardbeau3657]

@@jeralddcruz7325 STM32F407VET6 or STM32F407VGT6

[@rifqirizairfansyah200]

hey bro, i want know your shaft diameter

[@leopardbeau3657]

12mm

[@speedboy911]

So neat bro,good work what motor have you used in it?

[@leopardbeau3657]

Thanks.It is a 895 DC motor.

[@rasendriyafirdaus6690]

Is that strong enough for FFB? And how about the gear ratio configuration?

[@leopardbeau3657]

@@rasendriyafirdaus6690 not enough.1:5

[@inshallahberkah1632]

Minta tutorial diy ffb nya dari awal

[@selimcankaya5206]

hello Is the product available for sale

[@keep.it.street5771]

bro, which motor u use in ffb? maybe 775?

[@leopardbeau3657]

895

[@rildorodrigues9372]

Amigo,bom dia ! Qual programa usou ? Qual marca e modelo do encoder ? Qual marca e modelo do motor ? Quais arduinos e fonte ? Gostaria muito de montar meu próprio volante,pois ja fiz meu próprio pedal,e me deu muito orgulho ✌️✌️✌️✌️✌️ Desde já obrigado e parabens por seu trabalho

[@leopardbeau3657]

你好！ 我使用的是MMOS开源程序。 编码器规格是5V-24V、600脉冲。 电机是895有刷电机，BTS7960模块作为驱动。 这是STM32F407VET6方案，刷入MMOS开源程序。

[@rildorodrigues9372]

@@leopardbeau3657 o motor 895 seria dc12 24v?

[@leopardbeau3657]

@@rildorodrigues9372 是的。我建议用12V，电机发热会小一点。

[@rildorodrigues9372]

Certo ,tem alguma marca especifica do motor ? quanto ao.stm32 ,poder ser o blue ,ou tem que.ser a black pill?

[@leopardbeau3657]

@@rildorodrigues9372 我自己选的是一个便宜的电机，应该是小工厂制作的。我建议买你所在地区正规品牌的电机。 电路板的颜色不影响功能。

[@dawood8598]

How do you connect the steering with the laptop

[@leopardbeau3657]

FR4 PCB

[@gerald-jp7nd]

Please update project edit: and translate English

[@zugii]

Motor DC link ??

[@jeralddcruz7325]

Its 775 motor

[@uaydn_]

its not 775 its 895

[@adrianorocha7767]

Qual o torque? Ficou forte?

[@leopardbeau3657]

扭矩比较弱，可能不超过1NM。挺结实的。

[@MegaJereco]

Like like like

[@simracingos]

Here is a DIY tutorial for direct drive steering wheel hackaday.io/project/168801-diy-mmos-ffb-stm32-and-servo-drive-servo-motor

[@azzazz4549]

Just go out abd buy a wheel

[@EugenioCiullo_V-Blog]

encoder on belt? bad, very bad solution...

[@alanrones]

Like 827

[@uaydn_]

wtf is this power lol