DIY: How To Build a Fork Mount Bike Rack for $20 in 30 Minutes

  Рет қаралды 294,002

Singletracks Mountain Biking

Singletracks Mountain Biking

Күн бұрын

Пікірлер: 152
@eddy7680
@eddy7680 4 жыл бұрын
Everything worked out great. I built it right away. The only issue I found, was that the axel was not well supported due to the difference between the inside diameter of the plastic nipples and the axel itself. I also found the plastic was a little weak and the forks would pop out with a little twisting. I took a wooden dowel, pressed it in and drilled a hole through the middle. Now the axel has no wiggle room and is supper sturdy. Hopes this helps anyone with their project and thank you for putting up the video.
@trust5977
@trust5977 2 жыл бұрын
Please excuse my ignorance, but when you say drilled a hole through the middle of a wooden dowel do you mean lengthwise? If so, what sized drill bit did you use?
@DIYManiacJohnP
@DIYManiacJohnP Жыл бұрын
Attach t-mount to flange first and then mount flange to wood. This will ensure a tight connection of the t-fitting and also ensure that the fitting is properly aligned
@genso3065
@genso3065 4 жыл бұрын
I was looking for a fork mount to put on a 2x6 which is just 17$, but for one fork mount. Then I searched a diy and came upon your video. I'm stopping by home depot tomorrow. Haha
@joshwiegand
@joshwiegand 3 жыл бұрын
This is a great idea, I built one so I can store 2 mtbs in the back of my van under my bed. I guess the thing I wished I had done was to make sure the pvc nipples would fit the spacing of my fork as well as my thru axle. For the latter just bring your axle with you to Home Depot. Not trying to be a hater, just trying to save someone some hassle. Thanks for the great idea!
@singletracks
@singletracks 3 жыл бұрын
Great tip!
@everettbateman5864
@everettbateman5864 3 жыл бұрын
Just ran up to my local hardware store and got everything for my full suspension and dirt jumper!
@jojorice4594
@jojorice4594 2 жыл бұрын
Happy to Have It!
@zackaguilar5004
@zackaguilar5004 5 жыл бұрын
Made one last night works fine I'm also going to strap down the bikes after they're mounted for a extra secure ride. I think I'll get some extra quick release's to keep on the mount for the ease of not having to switch it back and forth.
@matthewleone5250
@matthewleone5250 4 жыл бұрын
Great video! Great idea! Any way to make this work for my two road bikes?
@trentay56
@trentay56 5 жыл бұрын
Fantastic! Perfect for my pickup. Will adapt for thru axles
@richardsun9371
@richardsun9371 3 жыл бұрын
Great design. I am building an inside car bike rack using a fork holder. Does the rear wheel need to be tied down?
@usernamemykel
@usernamemykel Жыл бұрын
What "axles" did you use????????????????????????????????
@dansuchy42
@dansuchy42 4 жыл бұрын
Thanks for the awesome idea and great step-by-step instructions! Just finished one for my van today - it holds my two road bikes securely and looks nice!
@hawkeyes2873
@hawkeyes2873 4 жыл бұрын
Very nice how many bikes can be accomodated
@toddanderson8277
@toddanderson8277 3 жыл бұрын
Great idea but curious if your bike is older and doesn't have the front hub easy lock vs the older screw on/off nut what can you use to secure the fork down? I'm looking to secure four bikes and I think the 2x6 idea with staggered hubs will work.
@LonnieWormley
@LonnieWormley 3 жыл бұрын
This is a great idea for my band build thanks a lot
@karstencostain5640
@karstencostain5640 4 жыл бұрын
Thank you so much😂I almost just spent around 50 on a mount, love it👍🏻
@martineguay6475
@martineguay6475 7 жыл бұрын
Hello! Thank you for this video... Very helpful. Can you please tell me the space between the fork of your bike. My Fat Bike is almost 6 inches between fork. Would this be ok for this size?
@funtivitycolton1930
@funtivitycolton1930 6 жыл бұрын
Hi Martine! Yes, you could still do this, just get longer pieces to insert into the T pipe :). It would technically work just the way it is but it will be more stable if you make it wider.
@rockbouchard4891
@rockbouchard4891 3 жыл бұрын
What about a fatbike 150mm wide fork or 135mm wide ??
@jeremydubrulle6686
@jeremydubrulle6686 4 жыл бұрын
Genius! Thanks so much mate ! Built my own thing way cheaper and way more fun!
@artravision
@artravision 5 жыл бұрын
Home depot will cut the wood for you. Great video!
@boltman01
@boltman01 3 жыл бұрын
Great video. Love all the haters who just feel the need to leave negative comments 😂 If you don’t like the idea or can’t figure it out, move on and do something yourself.
@rodneydives7385
@rodneydives7385 3 жыл бұрын
can you make this kind of thing for a roof rack with cross bars?
@singletracks
@singletracks 3 жыл бұрын
That could be tricky, but not impossible. You definitely want to make sure it is secure! Saris has a pretty cool modular system for truck beds that can also work inside an SUV. It's pricier than DIY, but looks a bit more polished. www.singletracks.com/mountain-bike-deals/?q=saris+traps+single+track
@kristyburchard3320
@kristyburchard3320 3 жыл бұрын
Fabulous! Building one this weekend.
@diegudr
@diegudr 3 жыл бұрын
How to you keep the 2 x 6 from moving front to back? Or is that not an issue?
@rnfaboy
@rnfaboy 2 жыл бұрын
You didn’t mention where you got the fork mounting rods that hold the forks to the rack
@singletracks
@singletracks 2 жыл бұрын
If you mean the 'rod' with the quick release lever that slides through the pipe/rack hardware, that's just the thru axle that comes with your fork. It's the same one the wheel rolls on so you should already have this!
@rnfaboy
@rnfaboy 2 жыл бұрын
@@singletracks so when you take your wheel off you just remove the thru axle bolt and use it for your mount. Thanks.
@singletracks
@singletracks 2 жыл бұрын
@@rnfaboy Right, when you remove the axle to take the wheel off, slide it back into the fork to secure the bike in the rack mount. This also helps you avoid losing the thru axle, which definitely can happen!
@misteryuz19
@misteryuz19 4 жыл бұрын
How about roadbike fork mounting? Is the size same?
@otarigabunia1078
@otarigabunia1078 3 жыл бұрын
HOLY-MOLY! YOU SAVED MY DAY!
@gslife1
@gslife1 4 жыл бұрын
Great video, just what I was looking for. Some of these comments below are unbelievable. Thank you for sharing this great idea.
@Rubeless
@Rubeless 4 жыл бұрын
Yes, there are some real winners. One guy complained about the sound, as if Cameron Crowe is the director...dics
@rodrigomazzola
@rodrigomazzola 7 жыл бұрын
Just saved me 250 bucks! ty a lot!!!!
@funtivitycolton1930
@funtivitycolton1930 7 жыл бұрын
No problem! I'm glad you liked it!
@cjones9058
@cjones9058 3 жыл бұрын
Any experience with the $15-20 fork mounts available from Amazon, etc, compared to this DIY option? Maybe those break easier? Or are the PVC nipples prone to breakage at all?
@edzukation
@edzukation 2 жыл бұрын
never seen a 70% off cart - is that in all the HD?
@singletracks
@singletracks 2 жыл бұрын
I don't think so. Just depends on if they have items they really need to get rid of.
@davidrowe8747
@davidrowe8747 3 жыл бұрын
Does this work only for through-axles? I didn't realise until the very end that this is for through-axles (maybe not for QR?)
@iseeker3845
@iseeker3845 3 жыл бұрын
Yes. But, I'm thinking of just using a block of wood and drilling a hole through it for my son's quick release
@user-ik9gw4wh4c
@user-ik9gw4wh4c 3 жыл бұрын
I thought your idea was great I brought all the components, being in Germany it cost me three times as much plus I had to bore the center of the PVC raisers out by 2mm and shorten the by 3mm to fit my 15x100 front axel. But hell it’s original.
@miguelcintron6595
@miguelcintron6595 4 жыл бұрын
That work for Axle thru, not for Q.R.?
@jeremyfranks9587
@jeremyfranks9587 6 жыл бұрын
How much was the quick release?
@cdig4
@cdig4 3 жыл бұрын
The 1/2” PVC close riser Does not fit a 15mm through axel.
@theoldgoat4525
@theoldgoat4525 4 жыл бұрын
This is so cool, will it work with through axles?
@messerole
@messerole 6 жыл бұрын
I am making this today. I have a 15mm boost. The 1/2 plastic nipples are not big enough for the axle to slide through. I bought the 1/2 set like you said but with the two nipples that hold the through axle being brass not plastic. The brass nipples are a perfect fit but there're brass. Also the 1/2 nipples (close) are 1 inch and not wide enough for the boost setup. I got the brass ones in 1 1/4 and it is a little wide. Gonna have to file this one down. I also got the entire set up in 3/4 instead of 1/2 and it works great. I'm gonna keep the 1/2 one to show friends and or let them use it. Thanks for the video.
@iseeker3845
@iseeker3845 3 жыл бұрын
wouldn't the 3/4" set have a lot of play with a 15mm thru axle?
@ahmedranderee5315
@ahmedranderee5315 6 жыл бұрын
what would i need to get to adjust this to a road bike?
@opinion5072
@opinion5072 2 жыл бұрын
Excellent video man really like the part where you lay out the prices thanks.
@singletracks
@singletracks 2 жыл бұрын
Thanks for the feedback, glad you like it!
@trevormick2248
@trevormick2248 5 жыл бұрын
Will this work for boost forks?
@michaelmeier310
@michaelmeier310 4 жыл бұрын
Fantastic! I had my doubts going into this but it worked out great! 👍
@locoboy23
@locoboy23 5 жыл бұрын
Hello ! Thank you so much for the instructions! I know this is an old post, but I have a Trek FX3 Disc, according to Trek website mine is: Wheels - Front hub -Formula alloy, 6-bolt disc, 12mm thru axle, 32h Do I use the same size as you? Thanks!
@Maccaroney
@Maccaroney 5 жыл бұрын
Nope. MTB have bigger axles by a few mm. You and i have 12mm diameter front axles whereas this guys' MTB is probably 15mm or so. I recommend taking your axle into your local hardware store and just looking for fittings that fit snugly and build from there.
@Noka1219
@Noka1219 3 жыл бұрын
1/2" is 12.7 mm, so 12 mm would fit not 15mm tho.
@blumenpedaler9516
@blumenpedaler9516 3 жыл бұрын
This is awesome! Thanks for the video!
@rickc2222
@rickc2222 7 жыл бұрын
video was meant for 15mm axles - mine is 20mm or 0.787", so I need to use 3/4" pvc pipe which is 20.93mm - close enough…
@user-yv2cz8oj1k
@user-yv2cz8oj1k 5 жыл бұрын
Is sat go for 3/4 inch anyway and convert down for 15mm. Fashions change. You got a list together yet?
@ray59401
@ray59401 4 жыл бұрын
My 15mm axle doesn’t fit. Guess I should have went 3/4
@Dmasters95
@Dmasters95 3 жыл бұрын
Doesn’t fit my 15 mm and the 3/4 is way too big
@iseeker3845
@iseeker3845 3 жыл бұрын
i have a 15mm thru axle and it didn't fit through the 1/2 pvc. HOwever, after boring the PVC with a 5/8" spade bit, it did.
@nikkiesteban
@nikkiesteban 5 жыл бұрын
what is the size for 9mm qr?
@mysho6317
@mysho6317 6 жыл бұрын
Thanks for Video & DIY solution........still fine tuning to match my needs but Your idea is the star of the show. Thanks again
@JamesRobertMTB
@JamesRobertMTB 6 жыл бұрын
This is such a rad idea
@bduntz
@bduntz 6 жыл бұрын
Where did you get the quick release from?
@brychli
@brychli 6 жыл бұрын
You can get these (cheap) on ebay.
@iseeker3845
@iseeker3845 3 жыл бұрын
it's not a quick release, it's a 15mm thru axle
@rickc2222
@rickc2222 7 жыл бұрын
Awesome, I'm doing this for a cheap single hitch mount....
@johncb5865
@johncb5865 7 жыл бұрын
I guess for a boost set up, use different PVC fitting?
@funtivitycolton1930
@funtivitycolton1930 6 жыл бұрын
You got it! Pretty simple swap.
@kateharvath
@kateharvath 2 жыл бұрын
Brilliant!!!
@singletracks
@singletracks 2 жыл бұрын
🙌
@vladimirkocurek
@vladimirkocurek 3 жыл бұрын
PERFECT!
@anthonytiburcio9260
@anthonytiburcio9260 3 жыл бұрын
Great video!
@imemovengeance
@imemovengeance 5 жыл бұрын
Does 1/2 inch pvc fit 15mm thru axles?
@swimpitt95
@swimpitt95 5 жыл бұрын
No. I tried this with 1/2 for my 15x100 TA and axel does not fit through the plastic close risers.
@hornkid
@hornkid 5 жыл бұрын
Yes it is possible to make this work for boost with 1/2” pvc risers! I was able to make it work by boring the plastic risers slightly using a file. It probably added about 10 minutes to the job. It turned out great actually and has a nice tight fit.
@iseeker3845
@iseeker3845 3 жыл бұрын
I used a 5/8" spade bit to bore the holes slightly larger; we'll see how it holds up.
@whutdatytopsy9651
@whutdatytopsy9651 4 жыл бұрын
That looks awesome!
@mailloux093
@mailloux093 4 жыл бұрын
Does not fit 15 x 110mm axle
@jvcardesign
@jvcardesign 4 жыл бұрын
very cool. This gives me some ideas.
@okioki1131
@okioki1131 6 жыл бұрын
Im in Colorado too, good vid!
@aboutsean
@aboutsean 2 жыл бұрын
For $27 you can buy a fork mount on Amazon and it's lockable! This seems like a solution to a problem that doesn't exist.
@singletracks
@singletracks 2 жыл бұрын
Good point! Some of the non-locking ones are as low as $20 on Amazon (and they only work with QR axles), though that's per bike mount so if you want 3 you're looking at $60-80+. For those on a very strict budget, black pipe still might be the way to go. Locking mounts from a reputable brand like Yakima cost $70 each.
@paulysci925
@paulysci925 6 жыл бұрын
used they're like $30 on Craigslist and you could spend the 30mins driving to pick one up?
@paulysci925
@paulysci925 6 жыл бұрын
oh i see through axle compatibility because of through axel being the standard now. i forgot because i still have qr. this would be handy if i keep my bike may ride it another year and go through axel for future ease of compatibility.
@alonzomartii
@alonzomartii 6 жыл бұрын
So PVC nipple was .38¢ or .34¢? :)
@JA-gx4hb
@JA-gx4hb 4 жыл бұрын
Could use more detail on how to attach bikes. Seems like a sudden stop would cause bikes to rotate up and slam into rear window. Please try it and show video.
@senglebe
@senglebe 3 жыл бұрын
the bike is long enough and enough of a counter balance that that shouldn't really happen, but you could run a strap through the rear tires if you're worried about it. I like this concept generally, but I don't like how loose the axles would fit. I bought an aluminum one of Amazon instead for around $17 a piece that is designed to fit the 15mm x 110mm axles of modern mountain bikes.
@nickngaopraseut6717
@nickngaopraseut6717 5 жыл бұрын
Yo that’s awesome!
@BlueOvals24
@BlueOvals24 2 жыл бұрын
Great idea right up until the part where you have to remove your bikes wheel to make it work
@singletracks
@singletracks 2 жыл бұрын
Definitely not as convenient as a tailgate pad but depending on your truck setup this can be handy. It's incredibly secure as well.
@BlueOvals24
@BlueOvals24 2 жыл бұрын
@@singletracks I'm sure it's solid. I'm thinking about getting a tailgate pad though, just not sure if it will work with my tonneau cover. I might consider a bike with a quick disconnect wheel, but I'm not sure if I want something that makes it even easier to get stolen.
@keithc728
@keithc728 5 жыл бұрын
That's nice. I only wish I still had my pickup
@just4all1
@just4all1 4 жыл бұрын
i got the bike, and i got the stuff for the rack, now all i need is a truck
@user-yv2cz8oj1k
@user-yv2cz8oj1k 5 жыл бұрын
I'll pick most of the parts up when I'm in California again. You don't want to know the prices for these parts here. 🤣
@pbearzzz2939
@pbearzzz2939 5 жыл бұрын
Brilliant!
@rbd104
@rbd104 3 жыл бұрын
Or you can buy quick release mounts, they look better, are not much more in price and come with a skewer already.
@ibaher1
@ibaher1 3 жыл бұрын
Where can I buy the quick release mount? Any link would be appreciated
@MichelBakhos
@MichelBakhos 7 жыл бұрын
Thank you thank you
@funtivitycolton1930
@funtivitycolton1930 7 жыл бұрын
No problem Michel! Glad you liked it.
@clenilma100
@clenilma100 Жыл бұрын
I was very nervous putting my brand new beach cruiser on this rack. kzbin.infoUgkxG6JIgwJhur8_Rg8UeQ3EmePzi_wSncL8 But after reading many reviews I decided to get this one and take a chance. When arrived it was very simple to adjust and put together. I also added spike tape over the metal hooks before securing and tightening the straps, and no scratches. I also purchased the top bar made by the same company so that my cruiser sits straight on the rack without having to turn upside down. Extra bungee cords are used to secure the front wheel from flapping and even piece of mind knowing your bike is secure. Definitely recommend...
@aliscia70
@aliscia70 5 жыл бұрын
grazie amico mio mi hai fatto risparmiare un mare di euro
@gilboston20033
@gilboston20033 5 жыл бұрын
I dont see the bike on it. I have to give one star, lol
@gregkosinski2303
@gregkosinski2303 5 жыл бұрын
"first we're going to want to grab our wood."
@vzangla
@vzangla 4 жыл бұрын
check and check.
@jvcardesign
@jvcardesign 4 жыл бұрын
hahahahahahhahaha
@PeterHartman1
@PeterHartman1 7 жыл бұрын
Here is a $5 version that looks just as functional. kzbin.info/www/bejne/h4G0lnanp8prpqs . Just use plastic pipe and the metal straps and you should be good to go. The grey electrical pvc is uv stabilized if you want to skip the painting step.
@funtivitycolton1930
@funtivitycolton1930 7 жыл бұрын
Interesting build! Nice and cheap.
@tmfrs2
@tmfrs2 7 жыл бұрын
All you have to do now is make the wood waterproof :D
@billj121
@billj121 7 жыл бұрын
Use decking material = waterproof.
@tmfrs2
@tmfrs2 7 жыл бұрын
Ah ok, thx bill
@nikolusmatthews8889
@nikolusmatthews8889 5 жыл бұрын
What glasses are those?
@robertt251
@robertt251 5 жыл бұрын
Viper
@ClayJ926
@ClayJ926 6 жыл бұрын
What am I missing? Half-inch diameter is less than 13 mm, through-axle is 15 mm…seems like if I wedge the axle in it’s not coming out very easily.
@laidavid
@laidavid 6 жыл бұрын
ClayJ926 I am wondering the same??!
@shredwithscott
@shredwithscott 6 жыл бұрын
Just tried this and the PVC nipple is probably .5 mm too small. I’m thinking I’ll just run a 5/8 drill bit through them to enlarge it a bit. Now if only I had a 5/8 bit.
@shredwithscott
@shredwithscott 6 жыл бұрын
The fittings are pipe thread, so a 1/2 NPT fitting only defines the threads and pipe OD, it doesn’t specify the ID. One table I found says 1/2” NPT is .622” ID, which is 15.8 mm, but the PVC fittings must be a tad thicker.
@davelai8324
@davelai8324 6 жыл бұрын
Scott Ziesman I used my dremel to make the pvc fitting slightly larger to fit the 15mm axle
@ClayJ926
@ClayJ926 6 жыл бұрын
1/2" electrical conduit connectors actually fit the axle nicely, but then they don't thread into the metal pipe.
@bodiless99
@bodiless99 4 жыл бұрын
You could have added more detail (some, ANY) about how you attache the bike. #imanovice
@TTPHOTO_15
@TTPHOTO_15 5 жыл бұрын
I don't trust putting my through axle through that you might scratch it
@LV2XPLR
@LV2XPLR 5 жыл бұрын
The axle will only touch the plastic nipples. Its unlikely plastic would ever scratch the axle.
@DROY2004
@DROY2004 4 жыл бұрын
Here’s a pro- tip for you, get a wireless mic so we can hear you, sound is very bad! Shalom!
@danielsonhobbies
@danielsonhobbies 5 жыл бұрын
$10 racheting straps from harbor freight or walmart will be easier and quicker. No need to disassemble front wheel. Same idea as tying down dirt bikes in pickup trucks.
@edwardgarcia3731
@edwardgarcia3731 4 жыл бұрын
That thing was trash.....didn't work! Bought quick release mounts with brackets on Amazon for $17! Done deal
@johnr8013
@johnr8013 3 жыл бұрын
Yep! Glad I looked at the comment section, going to use his technique with the 2x6 board and carabeaners just not the pipe fittings.
@Dmonieluv
@Dmonieluv 5 жыл бұрын
Suh-weet!
@jonathankrimer
@jonathankrimer 3 жыл бұрын
Step one, buy a truck. Doh.
@singletracks
@singletracks 3 жыл бұрын
Haha yeah.
@waitersluvhjy66
@waitersluvhjy66 4 жыл бұрын
Woodprix is nice for that.
@pineapsysportals5158
@pineapsysportals5158 4 жыл бұрын
terrible background music doesn't really add anything just makes it garbage more than you think
@shawnbartley7541
@shawnbartley7541 5 жыл бұрын
Thumbs down.... you dont ACTCUALLY show how the forks connect!
@Dmonieluv
@Dmonieluv 5 жыл бұрын
Through the quick release rods. Duuuh!
@andrewrivera4029
@andrewrivera4029 Жыл бұрын
I bought the fork mount bike block for 20 bucks, a bit more but worth it.
@trevorastley1727
@trevorastley1727 2 жыл бұрын
Over Engineered, much easier ways am sure.
@singletracks
@singletracks 2 жыл бұрын
Can definitely be simplified a bit. Any suggestions for improvement?
@ericgilmore9734
@ericgilmore9734 6 жыл бұрын
Clear coat or stain that wood man! JEEZ
@brandonl4432
@brandonl4432 3 жыл бұрын
Built it, doesn’t fit.... shit
@waitersluvhjy66
@waitersluvhjy66 7 жыл бұрын
Just do it yourself, go to WoodPrix page and learn how .
@puryeareaker7975
@puryeareaker7975 7 жыл бұрын
Check Woodprix mates. I love it to my wooden projects.
DIY Thru Axle Mount for SUV - MTB Fork Mount (How to)
5:00
Michiana Madman
Рет қаралды 36 М.
This Bikepacking Trend is a Gamechanger!
8:24
Path Less Pedaled
Рет қаралды 227 М.
Try this prank with your friends 😂 @karina-kola
00:18
Andrey Grechka
Рет қаралды 9 МЛН
Cheerleader Transformation That Left Everyone Speechless! #shorts
00:27
Fabiosa Best Lifehacks
Рет қаралды 16 МЛН
UFC 310 : Рахмонов VS Мачадо Гэрри
05:00
Setanta Sports UFC
Рет қаралды 1,2 МЛН
人是不能做到吗?#火影忍者 #家人  #佐助
00:20
火影忍者一家
Рет қаралды 20 МЛН
How To Build Your Own Bike Work Stand in Just 30 Minutes
4:11
Singletracks Mountain Biking
Рет қаралды 615 М.
Tiny Truck Bed Bike Rack: INNO RT202 / RT201
4:31
RunBikeMike
Рет қаралды 37 М.
Bike Mount Inside Vehicle DIY - No More Bike Rack!
8:03
Dirt Tramp MTB
Рет қаралды 73 М.
Small Truck Bed BIKE RACK with Additional Storage
6:20
Specific Love Creations
Рет қаралды 35 М.
Simple Homemade MTB Bike Mount - £30 & 30 Minutes - Just Brilliant
6:34
Mike's MTB Adventures
Рет қаралды 42 М.
This DIY Bike Rack Hack Saved Me $250!
10:03
Neil Koch: Dig-Drive-DIY
Рет қаралды 48 М.
How to Build the Ultimate Overland Truck Bed Kitchen Drawers for Camping!
20:50
Blake Weber (The Weber Woodshop)
Рет қаралды 7 МЛН
5 Better Tips For Transporting Your Bike
12:26
Daily MTB Rider
Рет қаралды 1,1 МЛН
9 Genius Garage Hacks In 9 MIN // For MTB and More
9:03
The Loam Ranger
Рет қаралды 606 М.
Try this prank with your friends 😂 @karina-kola
00:18
Andrey Grechka
Рет қаралды 9 МЛН