DIY | How to make Joystick and Buttons controlled Remote car using Arduino | nRF24L01

[@BhimSingh-vk4pv]

Thank you bhai bhaiya ji ye wala project dene le liye i love you bro

[@fouzanjaved5441]

sir, I really love your videos. keep the good work, sir.

[@ElectronicsisLife]

Thank you, I will.

[@marklee1907]

thank you very much for your fast response , i try it.

[@vyomarobotics8873]

working fine 😇 ! even tried this with nrf24 with antenna module and it is fine

[@amarnadhtechknowlogic7670]

Sir it is not working for me please help me sir please

[@marklee1907]

Thank you very much , I try to make .

[@marklee1907]

Hi , I according to your code and wiring diagram to build the car, but no any action, Pls, advice me,

[@ElectronicsisLife]

Do the connections using wires and soldering iron. Please pause the video to have a look at bottom side of the pcb to see how I did it.

[@Zdichck]

Can it be combined with HC-SR04 & Servo and work in two seperate modes: remote control and obstacle avoiding?

[@ElectronicsisLife]

It can be, but we need to attach ultrasonic sensor and then write code for it. It would be different project altogether.

[@tatchmeneses2545]

Is it okay to use both arduino nano?

[@ElectronicsisLife]

Yes. Same code can be use in that case too.

[@kenbiringer8071]

Hello. Is there a code to control speed?

[@ElectronicsisLife]

No.

[@manasrathod11]

I was finding the vid. Of Arduino based rc car which can steer it self with servo motor in the front just like an actual car, So the question is can i use servo in it, and if yes then tell me where to connect it.

[@ElectronicsisLife]

yes one can do that, you need to find the mechanism to connect servo at front. you can find it on KZbin itself.

[@marklee1907]

Hi, I fixed the problem, the car can work, but the speed not fast, too slow, would your advice me how to increased the speed. thank you.

[@ElectronicsisLife]

Glad to hear that its working, Check the voltage going towards the motor driver. Make sure to charge the batteries. I was getting decent speeds.

[@Ajay20100000]

Really awesome, But to control the speed?

[@ElectronicsisLife]

Thank you, Speed control not implemented yet.

[@Ajay20100000]

@@ElectronicsisLife Please update in next video.

[@ElectronicsisLife]

I shall consider it.

[@diyrobotronics]

Bro I can't extract the code so bro plz re-upload the code on video description

[@fouzanjaved5441]

sir, please make me a 4 dof Bluetooth-controlled robotic arm car project and give me the circuit diagram and code of the 4 dof Bluetooth-controlled robotic arm car project. sir, I really needed the 4 dof Bluetooth-controlled robotic arm car project.

[@ElectronicsisLife]

Yes will do it in future.

[@Bulbulle_lifestyle]

How to get code plz new suscriber

[@ElectronicsisLife]

Link for the code in the description.

[@fouzanjaved5441]

sir, can you still make me a line follower Arduino robotic arm car project and also give me the circuit diagram and the code of the line follower Arduino robotic arm car project. sir, I needed the line follower Arduino robotic arm car project.

[@fouzanjaved5441]

sir, can you till make me a joystick-controlled Arduino robotic arm car project and also give me the circuit diagram and the code of the joystick-controlled Arduino robotic arm car project. sir, I really needed the joystick-controlled Arduino robotic arm car project.

[@ElectronicsisLife]

Sure, It will take sometime.

[@fouzanjaved5441]

@@ElectronicsisLife thank you,sir.